There is always residue in the blender, what should you do to clean the blender thoroughly?

In our daily life, we always use a blender to stir the minced meat, but every time after use, cleaning is a particularly big problem, and we want to clean the blender quickly, in fact, there are many small tricks. usYou can put the egg shell in the blender, and then add some water to it to stir, so that it is easy to clean the blender after stirring for a while.

Pour a few drops of detergent and appropriate warm water into a blender。Warm water breaks down grease more effectively and helps remove oil stains. If cold water is used, it may need to be repeated twice to achieve the degreasing effect.

After that, start the mixer and let it start mixing the detergent with the added water. Note that it only takes a few minutes. When the mixer stops working, turn off the power.

Remove the blender, rinse with clean water, and check again. If you still feel scum or greasy, repeat until clean. Finally, turn the blender upside down to dry.

You can also put the steamed bread in a blender and use the steamed bread to clean it. Throw the steamed buns in, cover them, and continue stirring for about half a minute. You can see it during the stirring.

Okay, stop. I'm not teaching you how to make steamed bread. Look, pour it out.

The oil in this blender is sucked out by the mantou crumbs. Did you know that this steamed bun is used to absorb greasy and residual meat residue in the blender? This blade is also found in the cylinder.

It doesn't look as greasy. After washing in this way, the mixer will be cleaned after a simple rinse.

If the blender is really dirty, you can also mix baking soda, vinegar and detergent, stir for a while, then let it sit to soak overnight, then stir so that most of the stains will be washed off。For stubborn stains, you can try brushing it with a toothbrush.

If you want to clean the blender thoroughly, you can add the appropriate water and dish soap to it, and then start the blender and let him mix it himself.

You can grind it with a stone first. According to the capacity of the concrete mixer, measure a certain number of stones (for example, 2 tons of stones in 2m groups), turn for a while, and make some concrete with low strength grind down quickly. Then the people who enter the city use iron drills and steel hammers to clean up.

Remove the blender and clean it with clean water. Or use some scrubbing tools to clean the blender and slowly scrub it with clean water.

A quicker way is to add water to the blender, turn on the switch of the blender, let it stir in the water for a few minutes, and wait until the water becomes cloudy and cleaned.

It is recommended to rinse it on running water, and then carefully clean it with a brush, and finally there will be an automatic cleaning function on the mixer, which must be used reasonably!

Place the egg shells in a blender. Then, pour in clean water and start stirring, you can see that the eggshell is stirred into fine crumbs, and at the same time, countless small crumbs have washed away all parts of the inside.

Doesn't the current blender have a cleaning button, if there is no cleaning button, the food must be cleaned immediately after stirring, and it will be very clean and cannot be left for a long time.

In fact, this is relatively simple, and it must be cleaned up in time after each use, otherwise it will become more and more difficult to clean.

1.Hidden dangers:

1) The internal parts and screws of the mixer are easy to loosen, which may lead to the failure of mechanical and electrical equipment;

2) The mixer may have the danger of high temperature, high pressure and explosives failure;

3) The mixer operator may be injured due to improper operation of the mixer;

4) The mixer may have the danger of polluting the surrounding environment;

5) The mixer may cause the machine to run unsteadily, increase the noise, etc.

2.Precautionary measures:

1) Check the parts of the mixer regularly to make sure the screws are firm;

2) Check the voltage and temperature of the mixer regularly to ensure safety;

3) The mixer operator should master the correct mixer operation skills;

4) When the mixer is running, effective preventive measures should be taken to prevent environmental pollution;

5) The mixer should be maintained regularly to ensure that the spike file of the machine is stable and the noise is low.

The best way is to disassemble and clean, in general, the mixer in order to take into account the problem of cleaningWhen making parts, it is more inclined to be suitable for disassembly and cleaning, so after using the mixer, if there is really a lot of residue in it, then if you want to clean the mixer thoroughly, only this method is now the simplest and cleanest, but this method will definitely consume our time and labor, so friends with less labor and time may feel more headaches, so I have summarized several for you according to my own experience to be relatively easy. The cleaning method is shared with you, I hope it will be helpful to you:

1. Use special cleaning agents

First of all, we can use a special cleaning agent to clean it, because in view of this cleaning problem, there are now many places selling this special cleaning agent, the price is not very expensive, only need to mix it in a certain proportion in water, pour it into the mixer, and then turn the mixer in an open state for 3 5 minutes and stir it, you can let these cleaning agents clean the residue in the mixer, and then we can pour it out.

2. Use baking soda

We all know that baking soda has a strong corrosive cleaning effect, so we can also use baking soda to clean some of this thing, but relatively speaking, although baking soda is cheap, it may be difficult to clean too large tools, so this method is only suitable for some small and medium-sized mixers, so it is still more difficult for large mixers.

3. Use alcohol or sulfuric acid

Alcohol or sulfuric acid has a very strong cleaning effect, so for the residue in the mixer, if we really have no way, we can also use an appropriate amount of alcohol or sulfuric acid to clean, but both of these substances are very dangerous, so we must pay attention when using, especially try to avoid this kind of thing, direct contact with our **, or should be away from the fire.

Prepare a large basin of water, which can accommodate the mixer, and then put the mixer in the basin, the water should be full, and the residue will automatically surface the water, and you can rinse it with a high-pressure water column.

I think it's just a matter of rinsing with water after stirring. Because if you want those residues to not stick to the mixer's mixing center. This one is more difficult.

The blender should be rinsed several times with clean water immediately after use, so that the residue can be washed off more easily

The mixer must be disassembled and cleaned, and the detergent with good oil effect must be put in the cleaning process, only in this way can it be thoroughly cleaned.

Wait until the blender dries naturally, then use a small brush for the blender to brush on the blender, and finally put the blender into the sink and rinse it with clean water.

This method is suitable for all concrete mixers!

There will be residue every time the concrete mixer is discharged, if it is not cleaned for a long time, it is easy to bond, especially the position of the mixing shaft and the discharge port, the commonly used cleaning method is to flush with water, but due to the nature of concrete, it is simple that water flushing can not well clean up the residual concrete, so let's introduce a super simple method to deal with the residue of the main engine of the mixing plant.

We take a concrete mixer as an example, according to the ratio of the choice of kilograms of stones (note: only need to use stones, other materials do not need), stirring stones for 2 3 minutes, the purpose of which is to make the concrete that has just been bonded or has low bonding strength grind down, generally cleaning once a day or cleaning once a shift is better; If it is not cleaned for a long time, then the strength of the bonded concrete is high, in addition to rubbing with stones, it also needs to be cleaned with iron drills and hammers. Cleaning the concrete mixer is a job to be done every day, so once you find it, you have to clean it in time.

Great Wall Construction Machinery reminds everyone to remember: when workers clean up the residue of the mixer, all power should be cut off, the door of the control room should be locked, and at least 2 people should work together during the internal cleaning, and there should be a special person to take care of it to avoid accidents.

1.It is forbidden to remove the concrete accumulated in the concrete mixer barrel by hammering, and can only be removed with a chisel;

2.After the concrete batching plant stops working, pour water and stones into the mixing drum for 10 15 minutes for cleaning, and then remove the water and stones. Note that when cleaning, the power supply should be cut off;

Before the mixing plant needs to clean the mixer, make these preparations and work in it safely!