How to replace the computer mechanical keyboard switch?

How to disassemble the shaft of a mechanical keyboard.

Since the switch of the keyboard is the most important part of the mechanical keyboard, how to skillfully and accurately disassemble the mechanical keyboard switch has become a lesson that everyone must learn. First of all, for those high-end, mechanical keyboards with steel plates, we need to use a solder rod and an electric soldering iron, use solder after heating the electric soldering iron, after the solder is sucked up, use small tweezers or other tools to clamp the shaft tightly, and at the same time clamp the bayonet of the steel plate, so that the shaft can be smoothly disassembled, after completing such steps one by one, and finally continue to use the electric soldering iron and solder to re-solder the contact point just now. If your mechanical keyboard is not a high-end mechanical keyboard and does not have a steel plate design, then the step of removing the small tweezers to clamp the bayonet in the previous step is done.

What to pay attention to during the disassembly process.

For most people, the mechanical keyboard is an exceptionally "delicate" peripheral product, how to avoid damage to the keyboard as much as possible in the process of disassembly? First of all, we have to master a small trick, that is, after the keyboard is unpacked, we must leave the original gift buckle, and when disassembling it, we have the buckle as a gadget, which can avoid a lot of damage caused by excessive force. Secondly, when using the key puller, try to avoid other foreign objects falling into the keyboard shaft at this time, otherwise the mechanical keyboard will be repeatedly cleaned, and the damage to it will be very large.

How to disassemble the mechanical keyboard switch body.

1. First of all, for those high-end, mechanical keyboards with steel plates, we need to use solder rods and soldering irons, use solder after heating the soldering iron, and after the solder is sucked up, use small tweezers or other tools to clamp the shaft tightly, and at the same time jam the bayonet of the steel plate, so that the shaft can be successfully disassembled;

2. If it needs to be replaced, just use an electric soldering iron and solder to re-solder the contact point after replacing it;

3. If your mechanical keyboard does not have a steel plate design, you only need to remove the small tweezers to clamp the bayonet to disassemble it;

The key switches of some mechanical keyboards can be plugged and unplugged directly, as long as you buy the plug-in switch keys and plug them in. The axis of your mechanical keyboard should not be directly plugged and unplugged, so the shaft cannot be changed directly.

First of all, of course, it is necessary to disassemble the keyboard first - I found that the shaft, the steel plate, and the shaft circuit are all one, and if you don't start from the bottom, you can't take any of them.

The following gives the method of disassembling the axis of the mechanical keyboard:

Materials required: keycap puller, shaft puller, mechanical keyboard.

1. Prepare the two gadgets in the picture below, which are the keycap puller and the shaft puller.

Second, the keyboard needs to remove the keycaps first, and then use the keycap puller to clamp the two sides of the keycaps and pull them up to remove them.

3. Then use the shaft puller, insert the two tips of the shaft puller into the hole of the key shaft, and then pull it up to pull it out.

The mechanical keyboard shaft changing tutorial is as follows:Materials: mechanical keyboard, tweezers.

Step 1: Open the outer spike hand shell of the mechanical keyboard.

Step 2: Use the tip of the tweezers to align the gap between the satellite axis axis and the space chrysanthemum, stabilize the space bar with your hand, and use the tweezers to pin the lower edge of the space to warp upward, a section of the space has gone up to the family resistance, and then use the same method to warp the other side, left and right evenly force, a few times the space will come down.

Step 3: Pry open the upper cover of the mechanical shaft with tweezers, pin the left and right buckles of the upper cover with the tip, and warp it hard to get the shaft down.

Step 4: Take out the spring, replace it with a new one, put it in, and close the lid.

Most mechanical keyboards need to disassemble the keyboard and remove the keycaps when changing the shaft, if only one switch body is replaced, there is no need to remove all the keycaps, only one keycap can be pulled.

1. First plug the soldering iron into the power supply, then wait for 1 minute to reach the appropriate temperature, take out the disassembled mechanical keyboard circuit board and reverse the back, and see that a key switch is fixed at the position shown in the figure below.

2. Then use the heated soldering iron to dissolve the tin in the back.

3. After dissolving the tin, use a tin suction device to absorb the tin.

4. Then use the empty mandrel to pass through the key shaft hole below and rotate it slowly.

5. To the corresponding keyboard axis on the front, gently pry it open with tweezers to take out the shaft on the mechanical keyboard.

Mechanical keyboard quick disassembly and shaft replacement.

OK. Changing the shaft has basically become one of the essential skills of the DIYER of the mechanical keyboard. As long as you master this skill, you can replace the stinky shaft (the shaft body with a sense of passage loses the sense of paragraph), or replace the shaft body that is astringent or stuttering.

In addition, it is also popular to replace the transparent shaft cover and install the paper between the shafts. Replacing the transparent shaft cover can make the light more uniform, and the paper between the shafts can effectively prevent the volatilization of the lubricant inside the shaft body, and the visual effect is also very prominent.

Theoretically speaking, it is possible, of course, the normal mechanical keyboard needs more tools to change the shaft. Didn't there be a lot of keyboards that could be plugged and unplugged last year?,It's very convenient.,Change the shaft directly.,It's done in a few seconds.。

Some are hot-swappable and can change shafts, most of them are not, I use Rapoo's V510 Internet café version.

The mechanical keyboard is too simple to change the axis, and the beauty network discipline can be changed by yourself once.

The A-axis of the keyboard doesn't feel good, so I need to change it.