My computer screen is always flashing, the refresh rate is adjusted to 85 or flashing, and my eyes a

Updated on number 2024-03-03
9 answers
  1. Anonymous users2024-02-06

    I've done this too.

    1. On my computer, right-click - Properties - Advanced - Performance - Settings - Visual Effects - Customize - Use a Shadow for Icon Labels on the desktop and tick it.

    2. If the above does not work, right-click on the blank space of the desktop, select the "Arrange icons", and remove the tick before "lock the web project on the desktop".

    3,If it still doesn't work,Desktop,Right click,Properties,Desktop,Custom desktop,Select web and remove the tick of the web page in the web。

    4. If it still doesn't work, Desktop, Right-Click, Properties, Settings, Advanced, Monitor, Frequency set to higher Hertz.

    I guess yours can be solved with the 3rd one.

  2. Anonymous users2024-02-05

    There may be 3 aspects to judge:

    1.Graphics card issues.

    Replug it in, clean the gold finger, and see if the fan is normal.

    If it doesn't work again, it will be replaced free of charge during the warranty period).

    2.Cable problem (replugging, checking VGA or DVI interface) 3Display issues (Check if the electrical outlet is powered on.) If it's convenient, connect it to other computers to see if it's normal).

    It's not possible to restore with one click. If you don't have a system disc ready, the optical drive can be used. Start the computer and press the DEL key, set it to a disc boot in the BIOS, insert the system disk and reboot, basically complete it automatically according to the steps.

  3. Anonymous users2024-02-04

    Repair the display, or replace it.

  4. Anonymous users2024-02-03

    The monitor has a field scan part that is faulty, replace the monitor

  5. Anonymous users2024-02-02

    Is there a magnetic field next to the monitor, such as a subwoofer or something?

  6. Anonymous users2024-02-01

    Summary. display, the possibility of hardware failure is relatively small. Lift the display DP cable socket up, which means that the DP plug should be plugged in tightly, so that the operation can eliminate the fault, and it should be the interface contact problem.

    There is no problem with 60Hz because the frequency is low and the data is relatively less susceptible to interference, while the refresh rate of 144Hz more than doubles the amount of data transmission, so it is susceptible to infection.

    If you have this kind of problem, it is recommended to replace a high-quality brand DP signal cable, which should solve the problem.

    Why does the refresh rate of the computer screen flash when it is turned up and it does not flash when it is turned down, and the 144 hertz that has been used all the time suddenly flashes away.

    display, the possibility of hardware failure is relatively small. Lift the display DP cable socket up, which means that the DP plug should be plugged in tightly, so that the operation can eliminate the fault, and it should be the interface contact problem. There is no problem with 60Hz because the frequency is low and the data is relatively less susceptible to interference, while the refresh rate of 144Hz more than doubles the amount of data transmission, so it is susceptible to infection.

    If you have this kind of problem, it is recommended to replace a high-quality brand DP signal cable, which should solve the problem.

    If your monitor has a black screen and a flickering screen, one reason is that your voltage is not very stable, and another reason is that you adjust the 144Hz to be relatively high!

  7. Anonymous users2024-01-31

    The computer refresh rate is 60 without flashing 120 rear screen flashing card.

    Hello! The computer refresh rate is 60 without flashing 120 after the screen flashing card solution 1, right-click on the desktop - > properties - > settings - > advanced - > monitor - > the screen refresh rate, CRT to 75Hz or above, notebook computer LCD screen LCD to 60Hz. 2. In fact, the main reason for the screen shake of the LCD screen is that the refresh rate of the LCD is set below 75Hz, at this time, the screen often shakes and flickers, we only need to increase the refresh rate to more than 75Hz, then the phenomenon of the computer screen shaking will not appear again.

    3. Sometimes due to the age of the LCD monitor, there will also be jitter. In order to check whether the electronic components inside the display are aging, you can connect the faulty monitor to someone else's computer for testing, if the fault still disappears, it means that the monitor is broken and needs to be repaired.

  8. Anonymous users2024-01-30

    Hello landlord. = =

    If this situation arises, I will give you four ways to do it (and I have successfully solved this situation).

    1. Right-click "My Computer" Properties Advanced "Performance" bar and click "Settings" Visual Effects Check "Use shadows for icon labels on the desktop", and click "Apply" to exit.

    2. Right-click the desktop -- arrange the icons -- remove the tick before locking the web project on the desktop.

    3. Right-click on the blank space of the desktop, click the "Properties Desktop Customize Desktop Web" option in turn, and then select the "Current Home Page" and "http ..." in the "Web Page" columnWait for all the checks in front of each item to be removed ("http......"In order to add web pages or ** addresses from the Internet, generally not needed, you can delete them all), and remove the tick in front of the "lock desktop project" below, click OK to complete the setting, and you can see the cute desktop icon again.

    4. Another situation is that after installing a certain program (such as the system prompt: whether to add the active desktop item to your desktop), the desktop text becomes opaque. In Run, enter " to open Group Policy; In "User Configuration Administrative Templates Desktop Active Desktop", click Enable Active Desktop, then click "Properties" to select "Disabled", click "Disable Active Desktop" "Properties" to select "Enabled"; After that, open the Control Panel, open the system in Classic View, and in the "Performance Advanced Options Performance Visual Effects Make Desktop Text Transparent" (equivalent to performing the first method later).

    — Over.

  9. Anonymous users2024-01-29

    What kind of display,Generally adjust the refresh rate of the display,60Hz of LCD,CRT display to keep about 75,If the refresh rate is right and flashing,It depends on whether there is a problem with the graphics card or the display。

Related questions
23 answers2024-03-03

It depends on what resolution you can brush up to 120

Low resolution can brush high brush heart rate, which has a bandwidth problem. >>>More

8 answers2024-03-03

It's either a software problem or a hardware problem. First soft and then hard to solve, you try the method I said, if it is successful, you will give me points. >>>More

13 answers2024-03-03

Nothing you shake with it on the line!

16 answers2024-03-03

It may be that your graphics card is not compatible with the game.

10 answers2024-03-03

I've had this phenomenon before, especially when it's dry, and it's more likely to happen when I hit someone's arm, and they were both shocked at the same time, and once I turned on the TV and sparks went from the tap. >>>More