Everyone help to provide what to pay attention to when making a shower room

The quality of the main material glass of the shower room is very critical, ordinary glass can not be used to make a shower room, tempered glass must be used, and the following four aspects must be followed: 1. There is a 3C certification mark, and it is better to print it directly on the glass with a laser; 2. The thickness of tempered glass is 4mm, 6mm, 8mm, 10mm and other specifications, generally 6mm and 8mm can be used; 3. Check whether the edge of the glass is damaged, whether the chamfering edge is smooth, and the probability of self-explosion after the installation of the problematic product will be much greater; Fourth, no matter how good the shower room is, there will be a self-explosion rate of 3/1000, so it is best to paste a layer of explosion-proof film on the glass, even if there is a real problem, the glass fragments will only adhere to the film and will not splash and hurt people; Now in addition to ordinary tempered glass, there are many businesses that have launched tempered glass or laminated glass with CCCS certification, which will be more expensive than ordinary tempered glass, and the product itself has explosion-proof function.

The aluminum of the shower room should be strong and poor, and the thickness of the aluminum is only, most of which are made of waste aluminum with the best in order to save costs, and the surface is more trachoma, pinholes, lines, dark color, soft texture, easy to deform or break, difficult to clean up at home, easy to rust, and easy to cause the shower room to explode. Good aluminum is not only strictly controlled in terms of material selection, but also has a multi-layer treatment on the surface, with a firm coating, bright tone, and no corrosion, and the thickness will be, and some can even reach 2mm.

The slide rail of the shower room should be smooth, and the slide rail of poor quality is difficult to pull, and the uneven force of the glass is easy to occur when pulling hard. Therefore, the wheel seat of the pulley should use compression-resistant and heavy-resistant materials, such as 304 stainless steel and high-end synthetic materials. The sealing of the wheel seat is good, and the water vapor is not easy to enter the wheel, so the smoothness of the wheel can be guaranteed.

The handle of the shower room should be safe, and the handle of the shower room should not be too abrupt, especially if there are elderly people and children at home, it is easy to be injured when hitting the handle with too sharp edges and corners when taking a bath. So it's best to choose one with a sleek appearance, easy to switch on, and effortless.

The following three points should be paid attention to: 1. In order to ensure the smoothness of the overall shower pulley, lubricant or peanut oil can be added appropriately. 2. When the pulley of the track-type shower room is loose or falling off, it is necessary to find maintenance personnel in time to adjust it to ensure that the pulley is effectively bearing the movable door, and then use a paper towel dipped in peanut oil to clean the foreign matter in the track to ensure smooth sliding; Avoid hitting the movable door too hard to avoid causing the movable door to fall off.

3. Do not hit the glass with sharp and hard objects, especially the four sides and corners. What you need to know is that the shower room is to be decorated to the later stage can be installed, but the shower room water strip is to be pasted into the floor tiles when the tiles, the reason for this is to have a good water retention, after the installation is complete, at this time it is necessary to use the back lyrical entire shower room to wipe clean, 24 hours must not be used, remember it to be quiet for a while, after completion, in the future use must also pay attention to cleaning and maintenance, so as to create a relaxed bathing environment.

The design of the shower room needs to pay attention to the size of the shower room, the way of opening the door, etc. Let's take a look at the specific precautions with life.

Size First of all, the shower room is where people stand inside and take a bath. It is limited by the small size of the bathroom. Generally, the size of the shower room is relatively compact, but in order to ensure that there will be no bumps when bathing, the length and width of the shower room should not be less than 800mm*800mm size.

The width of the shower room should be greater than 800mm to avoid crowding.

How to open the door.

Secondly, there are three commonly used ways to open the shower room: sliding door, inner door, and outer door. Among these opening methods, it is best to use the form of a sliding door, so that the opening will not have any effect on the inside and outside of the shower room; In general, it is not recommended to open the door inside.

The outdoor space is not affected, but if someone slips and falls in the shower and needs help, no one outside can push the door in. The best way to open the shower is to sliding the door.

The partition of the explosion-proof shower room is generally made of tempered glass, and the tempered glass will have a certain chance of self-explosion. Tempered glass can easily cause injury if it happens**. Just in case, it is advisable to put a layer on the glass of the shower room.

Explosion-proof film, so that even if the glass **, will not be scattered.

Water retaining strip design.

In addition to setting up a glass partition outside the shower to prevent water from splashing outside, it is also necessary to set up a water barrier under the glass partition to prevent water from flowing out on the ground. At the same time, this kind of water retaining strip can also be replaced with a long strip of floor drain + shower room partition combination. This design does not require a water barrier, allowing water to flow in and out of the shower room here.

Storage of bathroom items.

The shower room is mainly used for showers. At this time, hygiene products such as shampoo, facial cleanser, body wash, soap, etc. are also essential. The storage and storage of these items should also be considered when designing the shower room. Bathroom supplies are well stocked, making the shower room easier to use.

When making a shower room, you must choose marble, the glass of the shower room should be selected with C certification, and waterproof measures should be taken, the sewer treatment should be done, and some big brands of shower appliances should be selected, and dry and wet separation should be done.

We must do a good job of separating dry and wet, determine the location in advance, determine the decoration drawings in advance, purchase good materials in advance, and also make a budget in advance and pay attention to cost performance.

It is necessary to pay attention to the separation of dry and wet, the problem of drainage, the surrounding situation, the problem of waterproofing, and the need to pay attention to safety.

When designing the shower room, we must pay attention to the details, don't bring unnecessary trouble to ourselves, and when designing the shower room, we must design according to our own style, and when designing the shower room, we must design according to our own ideas, but I think the most important point is that when designing the shower room, we must find a professional to help us design, because those professionals know more than us.

1. When choosing a simple shower room brand, because the shower room is a non-standard production service product, it is necessary to choose a well-known and well-known shower room brand, so as to ensure the quality of the material selection for the shower room, and avoid choosing inferior shower rooms and unknown brands, these products often do not pay attention to after-sales service and quality. Don't be greedy when choosing, be sure to choose a product marked with the specific factory name, factory address and commodity certificate.

2. When buying a shower room in Zhengwang, the quality of the glass is particularly important, after all, it is related to the personal safety of the user, so it is necessary to strictly select the tempered glass.

3. The selection of aluminum is also very important, there are many unknown brands in order to reduce the cost of production, so they choose to make aluminum for construction, these aluminum materials are processed with very low aluminum ingot infiltration, that is to say, the use of waste aluminum for secondary processing, also known as copying aluminum, used in the door and window frames. Focal spine.

4. Check whether the pulley ball bearing is flexible.

The pulley of the sliding door of the shower room is also very critical, so the pulley must be flexible and light, and the screws are made of stainless steel. The Faenza sliding door shower room adopts high-grade pulleys, and its main materials, including bearings, are made of stainless steel, which is not rusty; Wear-resistant, smooth and free switching, no noise.

5. The purchase of shower rooms should be adapted to local conditions.

The choice of shower room should be considered according to the size of your bathroom space. Therefore, reserve the bathroom space before decoration, if the bathroom has 4 to 5 square meters, you can choose the shower room position of about 1 meter by 1 meter, and the bathroom has 8-10 square meters, then choose the one by meters, and the room height cannot be lower than the meter. Therefore, consumers should not only pay attention to the area and height of the room when purchasing, but also pay attention to the measurement and planning before the basic decoration, and reserve the location of drainage, water supply and wiring.

Otherwise, it will be reworked or inconvenient for future use.