I want to know how to operate a dump truck, how to draw a dump truck

Hello, glad to answer your questions.

The operation steps and precautions of dump truck are as follows:

1. The driving operators of the motorized dump truck must be trained in professional safety technology, pass the examination, and hold the "Special Operation Certificate" to work. It is strictly forbidden to drive on the highway without the examination and certification issued by the traffic department.

2. Check whether the fuel, lubricating oil and cooling water are sufficient before operation, the gear lever should be in the neutral position, and the heating water should be preheated when the temperature is low.

3. After the engine starts, it should be idled for 5 10min, and the first gear can start when the water temperature rises to more than 40, and it is strictly forbidden to start in the second gear and step on the accelerator to the end.

4. Be concentrated when driving, and do not carry people, smoke, or joke while driving.

5. The width of the transport component shall not exceed the width of the vehicle, and the height shall not exceed the calculation from the ground). When transporting concrete, the plane of the concrete should be 1o cm lower than the bucket mouth; When transporting bricks, the height shall not exceed the bucket plane, and it is strictly forbidden to overload.

6. In rainy and snowy weather, you should drive at low speed at night, and it is strictly forbidden to slide in neutral gear and go down a steep slope of more than 25° when going downhill.

7. When pouring material at the edge of the pit, a safety shield (20 cm 20 cm wooden square) must be set up from the edge.

8. When the dump truck goes up the ramp (horse road), the ramp should be smooth, the width should not be less than, and protective railings should be set on both sides, which must be inspected and accepted before it can be used.

9. When overhauling or brushing the car after shift, you must turn off the ignition and pull the hand brake.

I don't know what brand you're going to buy, it's hard to be clear.

Regardless of the brand, it's about the same, and the body lift is hydraulically operated, and the hydraulic tie rod is usually next to the driver's seat, which is very simple.

Hope it helps.

What brand of car do you want to buy and how big is it? What is the main pull? I can explain it to you in detail!

A B2 license is required to drive a dump truck.

B2 driver's license can drive the model for heavy, medium-sized trucks or large, heavy, medium-sized special operation vehicles, heavy, medium-sized trucks are mostly trucks, such as the usual road often seen to pull muck trucks are heavy trucks. Large, heavy and medium-sized special operation vehicles refer to vehicles equipped with special equipment or appliances, such as sprinkler trucks, concrete mixer trucks, fire trucks, etc.

Other permitted driving types of B2 driver's licenses are C1 (small cars) and C2 (small automatic cars).

C3 (low-speed truck.

C4 (three-wheeled vehicle) and M (wheeled self-propelled mechanical vehicle) are the same as B1 driver's licenses.

Hello, it is a pleasure to serve you and make the following answers for you: Vertical solutions to the Flip Bucket Bird Bureau: 1

First, check that the wheels of the dump truck are installed correctly, making sure that the axes of the wheels are perpendicular to the ground and that the distance between the axes of the wheels is consistent. 2.Secondly, check whether the bracket of the dump truck is installed correctly, make sure that the axis of the support belt frame is perpendicular to the ground, and the distance between the axes of the bracket is consistent.

3.Finally, check whether the distance between the bracket and the wheel of the dump truck is consistent, and ensure that the distance between the bracket and the wheel is consistent to ensure the verticality of the dump truck. Personal Tips:

During the installation of the dump truck, it is necessary to ensure that the distance between the wheels, brackets and axles is consistent to ensure the verticality of the dump truck. In addition, when using dump trucks, it is necessary to pay attention to safety and avoid accidents.

Hello, it is a pleasure to serve you and give you the following answers:1Reason:

During the use of the dump truck, due to improper operation, excessive load of the wheels or impact by external forces, the body may be deformed, resulting in the body not being kept horizontal. 2.Workaround:

1) Inspect the wheels and replace the damaged ones. (2) Readjust the body so that it is level. (3) Check the wheel bearing, replace the damaged bearing, and ensure that the wheel can rotate normally.

4) Check the tires of the car as early as possible, replace the damaged tires, and ensure that the wheels can run normally. 3.Personal Tips:

When using dump trucks, it is necessary to pay attention to the reliability of the wheels, and frequently check the wheel bearings and tires to ensure the normal operation of the wheels.

A dump truck pants Zheng is drawn as follows:

1. Draw first, the 'bucket' of the dump truck. Outline it with a combination of horizontal and diagonal lines.

2. Then, under the 'bucket', draw wheels on the left and right sides.

3. Connect the wheels with a horizontal line and outline the chassis line.

4. Outline the parts of the front of the car on the left. Draw with a combination of horizontal and vertical arcs.

5. Above the fitting, connect it to the left end of the 'bucket' with a diagonal line.

6. On the right side of the left wheel, use the combination of oblique and horizontal lines to outline the shape of a cup superimposed on the bottom of the bucket.

7. On the left side of the right wheel, draw a small circle, and then on the left side of this shape, draw two parallel diagonal lines to the upper left, and connect to the bottom edge of the bucket close to the figure of step 6.

8. Use horizontal and diagonal lines to outline the parts below the 'bucket'.

9. In the front part of the car, the details of the field of view window are outlined with two vertical lines and oblique lines below the 'bucket'.

10. Draw a ladder-like figure at the front of the car to outline the details of the 'bucket'.

Techniques and methods of drawing

1. Start with the simplest shapes. This is the basis for accumulating drawing skills, and only when you have the simplest shapes can you draw more complex paintings in the future. Therefore, before learning to draw, it is necessary to draw the basic shapes of various shapes and draw them in place, which is the key to ensuring that you can further improve your drawing skills in the future.

2. Follow the order of drawing from largest to smallest. Drawing the large parts first, and then the small aspects, is the key to ensuring that the overall painting is more beautiful. The key to ensuring that there are no flaws in the details of the painting is to draw the whole part first, draw the large part and then modify and improve the small part of the details, so as to be able to draw well, which is also one of the skills of painting.

3. Copy more paintings of famous artists. By constantly copying the paintings of various famous artists that you like, you can constantly improve your understanding of various shapes and lines and the feel of painting, so as to improve your painting skills. And improve your drawing ability in a targeted manner.

In short, it is not easy to draw a good picture, I recommend starting with the simplest shape, then following the order of drawing tigers from the largest to the smallest, and finally copying more famous paintings to improve your painting skills.

How to draw a dump truck:

1. Draw a horizontal straight line, and draw the outline of the front and chassis of the dump truck above the straight line.

2. Draw the body of the rice car.

3. Draw the details of the windows and goods of the Fandu car.

Fourth, give the corresponding color to the drawing, and a dump truck is done.

Dump truck refers to a vehicle that conveys materials over a short distance with a hopper that can be tipped over. It is suitable for short-distance transportation of concrete, sand, earthwork, coal, ore and other bulk materials such as construction, water conservancy, road construction, and mining. The hopper is installed in the front of the tire travel chassis and is tipped and discharged by the gravity of the material in the bucket or the thrust of the hydraulic cylinder.

It is composed of a sakura hopper and a walking chassis.