If you can t turn it on, the screen will go black when you turn it on5

Updated on number 2024-04-28
14 answers
  1. Anonymous users2024-02-08

    Did you have an alarm on the motherboard in this situation? If there is no alarm, it may be a problem with your graphics card, this has nothing to do with the CPU, check the connection between your graphics card and the motherboard and the connection between the color display and the graphics card. If not, it may be that you have adjusted the resolution too high in the system beyond the scope of use of the color display, and the solution is to enter the system security mode to modify.

    If none of the above is true, it is likely to be a motherboard problem, find a professional to test it!

  2. Anonymous users2024-02-07

    Memory is reinserted.

    Don't use the graphics card at all, and after removing it, see if it's a black screen to know if it's a graphics card problem.

  3. Anonymous users2024-02-06

    It's generally a memory and graphics card issue.

  4. Anonymous users2024-02-05

    CPU problem, I've suffered. There is a deep experience.

  5. Anonymous users2024-02-04

    This should be a malfunction of the mobile phone, or go to the store to find the master to see.

  6. Anonymous users2024-02-03

    It should be caused by insufficient memory, like this situation to flash the machine, generally between 30 and 40 flashing fees.

  7. Anonymous users2024-02-02

    It's hard to judge if this isn't described.

    The suggestions are as follows: 1. Whether the computer is out of power, check the power supply, etc.

    2. Check whether the lower wire is in poor contact.

    3, still not work, conditional replacement parts test, one by one to check 4, not will be sent for repair, back-end detection.

  8. Anonymous users2024-02-01

    There are generally three phenomena that cause computer crashes: first: the computer power supply is insufficient, the power supply voltage is unstable, or the power supply is broken.

    Third: the system is broken, and the system needs to be reinstalled to solve the problem.

    Fourth: The cause of the problem is the oxidation of the gold finger of the memory module or graphics card or the poor contact of the slot, which causes the computer to fail to boot up. Solution:

    You can turn off the power first, open the computer case, dial out the memory module, use the eraser to wipe the part of the gold finger (that is, the place where there is a copper sheet) back and forth a few times, and then insert a memory slot back in, and you're good to go. If you don't turn on the computer after doing this, you have to check the graphics card, explain that it is a problem with the graphics card, and you can do it in the same way as above.

    Fifth: Check to see if the cable between your computer and the monitor is loose.

  9. Anonymous users2024-01-31

    Press and hold the power button at the same time as the up and down keys to reset your phone.

  10. Anonymous users2024-01-30

    There are many reasons for the failure of the black screen on boot, such as damaged monitor, damaged motherboard, damaged graphics card, poor contact of graphics card, damaged power supply, damaged CPU, etc. For the treatment of the black screen of the computer, the method of eliminating and replacing is basically adopted, and the principle should be based on replacing and eliminating the most suspicious parts first.

    Unplug the data cable connected to the monitor and the console, and turn on the power switch of the monitor separately. Generally, if the display is normal, it will display the manufacturer's information of the display or a prompt that the monitor is not connected, if it can be displayed normally, it indicates that the display is unlikely to be damaged.

    Check that the exposure is good. You can check whether the contact between the graphics card and the monitor is good, whether the contact between the graphics card and the motherboard IO slot is good, and whether the contact between the memory module and the motherboard slot is good.

    If the black screen still appears, take out the components installed in the computer, leaving only the CPU, graphics card, and memory sticks, and the cause of the fault can be limited to the CPU, motherboard, and memory. Generally, if there is a fault in the memory, there should be an alarm sound. If the memory fault is ruled out, only the CPU and the motherboard are left.

  11. Anonymous users2024-01-29

    It is recommended to bring the phone and warranty card to the local official customer service center for testing and repair after the phone is fully charged.

  12. Anonymous users2024-01-28

    There may be batteries or lines, systems. The last time my phone couldn't turn on, it was a cable problem.

  13. Anonymous users2024-01-27

    The computer crashed, and the system needed to be redone.

  14. Anonymous users2024-01-26

    See if there's something wrong with the system.

Related questions
8 answers2024-04-28

The phone screen goes black when it is turned on.

Processing methods and steps: >>>More

15 answers2024-04-28

The phone has a black screen. Splash screen, blurred screen, white screen, recommended: >>>More

35 answers2024-04-28

According to what you said, that is, it is easier to start in the case of a hot engine, I think there should be two points, first, the power supply problem, the power supply of the chassis is somewhat aging, and there may be a problem with some capacitors, resulting in the initial power supply is sufficient. Second, the main version of the problem, I have encountered this phenomenon before, to the store for a professional to check, said that there are cracks on the motherboard, it is not easy to energize, after the machine is hot, the current between the gravitational force, coupled with the thermal expansion of the motherboard, the contact between the cracks will be a little better. It is recommended to take it to a professional to see.

7 answers2024-04-28

Problem analysis: There are two situations when the computer boots up the black screen: the display is not powered on (the power indicator is not on) or the display is powered on (the power indicator light is on) but there is no signal or the screen shows "no sighal", the former means that the circuit is not connected, or the power interface or power cord is in poor contact or damaged, and the latter is generally a loose or oxidized memory module and poor contact, or the display data cable is not in good contact, or the memory, graphics card, display or data cable is damaged. >>>More

5 answers2024-04-28

Ringing at startup: Constant ringing (long sound): The memory module is not plugged in tightly or damaged. Reinsert the memory module, or replace the memory. >>>More