Urgent How to Telecom 3G Shared Internet Access, a desktop, a laptop, if you can connect, add 50 to

Internet card - desktop - network cable - notebook, so connected.

Desktop Setup Dial-up Connection: Right-click Internet Neighbor Properties Select New Dial-up Connection on the left, select Connect to Internet, and then select Manually Set Connection, fill in your username and password after the name (such as CDMA), and remember to select your 3G network card when selecting Modem. When you're done, right-click on this connection (CDMA), select Properties, Share, and below allow other users to link to the Internet via the machine tick, and then OK.

In this way, after dialing in on the desktop, at the same time, the desktop also makes a ** server, and the notebook can also connect to the Internet through the desktop.

Then open IE on the notebook, Tools > Internet Options > Connect > LAN Settings > Auto-detect settings and tick it, and it's OK.

This method actually uses the system's tethering (i.e. your computer has at least two connections (e.g. your telecom wireless card connection and your computer's LAN connection)).

Let's take these two connections as examples:

1. Connect directly with a network cable (you need to set the IP, subnet mask and gateway of the two computers).

2. Dial up your telecom wireless network card to access the Internet (this one uses Telecom 3G to be in the first step to establish the network!) ）

3. Set up this notebook with Telecom 3G (online neighbor properties -> on the left "Set up home or small office network" - > ...... according to the wizard "Next".Until there is an option that says "This computer is directly connected to the Internet." Other computers on my network connect to the Internet through this computer. "Be sure to choose this one - > choose the connection of your telecom 3G network card - > select the local connection - > the next step ......Finally completed).

The main thing is that after the setting of the third step, two can be connected to the Internet (at least two more than one can also be a drop in network speed).

It is recommended that you check the LAN settings and gateway settings.

In the case of not increasing the device, you can allow other machines to access the Internet through the windows network card configuration, but the configuration is relatively complex, and the performance of the two computers will also affect each other, if the economic conditions permit, it is recommended to buy a 3G wireless router, 9611N of Shenhai Bell, Zhongguancun has a sale, about 450 or so, there are many compatible network cards, stable, and the configuration is simple, I am using it now, the effect is very good, and it saves a lot of trouble with configuration.

I also want to ask this question, you said you succeeded yesterday, how did you connect?

If you need to use your Unicom number to open QQ membership and other services, you can do so in the following ways:

Apply for QQ Yellow Diamond (i.e., "Home Improvement Consultant") SMS activation method: "QQH sent to 10661700". Information fee: 10 yuan per month, communication fee: yuan.

Apply for QQ Red Diamond (i.e., "Fashion Consultant") SMS activation method: "QQF sent to 10661700". Information fee: 10 yuan per month, communication fee: yuan.

Apply for QQ Green Diamond (i.e., "Entertainment Around") SMS activation method: "AD sent to 10661700". Information fee: 10 yuan per month, communication fee: yuan.

Apply for QQ Blue Diamond (i.e., "Game Secretary") SMS activation method: "QQY sent to 10661700". Information fee: 10 yuan per month, communication fee: yuan.

It seems that everyone tends to let you buy a route, and then set up a route sharing to surf the Internet. I'll talk about another way later, let's improve the router method first.

First of all, the hub in your hand does not have a basic memory function, so it can only be used to set up a local area network, to achieve the function of sharing the Internet, you can basically only rely on the router, as for the wireless and wired router, it all depends on whether your laptop has a wireless network card, and secondly, the difference between wireless and wired routers is about 20%, 6 ports have lines from generally around 120, and wireless 6 ports and 4 ports are about 150.

The wired router is relatively simple to set up, connect the WLAN of the cat to the WLAN port of the router, and then log in to the routing management page (the address is generally on the manual, and the broadband account password can be entered. Then connect the laptop to the remaining LAN ports of the router, and you can surf the Internet normally.

Wireless router, in addition to the previous connection with the cat,It's a little troublesome on the management page.,To set the password and the number of channels.,Then choose the communication protocol and wireless network card all the time,At present, the general is。 Then the other settings are similar and will not be repeated.

This involves the choice of wireless network card, generally 54MB is completely sufficient, unless your broadband is "10MB optical fiber", otherwise you don't have to listen to the computer dealer fool you into buying a 108MB network card.

I have perfected the method of the router in detail, you can refer to it.

My own method is to install a network card on your original computer, now the market 10 100MB adaptive network card is about 100rmb, and then log in to my computer - there will be 2 local connections, all set to connect and share, whether xp or vista have this function, and then connect the laptop and the new network card of the desktop to the network cable port to access the Internet.

Of course, there are pros and cons to each method, for example, the premise of my method is that the desktop must be on. However, it is recommended that you consider that it is more secure to use a router, and it is better for future wiring to expand your home network.

If you can't have a hub, you also need a router with routing function to share the Internet!

Connection method: The cat is connected to the router, and the router is connected to 2 computers.

Configuration method: 1 Router: Select PPPoe, fill in the username and password of your home broadband, select automatic dialing, and automatically redial when disconnected.

2 2 computers: The IP address of the network card must be in the same network segment as the router, and the two computers cannot be the same, otherwise there will be conflicts; The mask is the same as a router; The gateway is the router address; DNS asks telecom and he will tell you how much to fill in.

For example, computer A:

Mask gateway. DNS: Ask Telecom.

Computer B: Mask gateway.

DNS: Ask Telecom.

After this configuration, the router will automatically dial for you, you only need to turn on the computer to access the Internet, and the computer does not need to dial again

**Unclear discuss with me!

Give me the best for the following reasons:

Internet access mode: 1. Install broadband and use cable (current normal method).

2. Install broadband, buy a wireless router, your machine has a wireless network card, no need to plug in 3, buy a 3G network card, no need to install broadband.

According to your question, you already have broadband at home, you only need to install a wireless router, ** very cheap, within 100 is good... Easy to install, on the manual!!

Take a look at your adsl cat first

If you have an auto-dialing function, you can do it

Go to the settings to set the cat to automatic dialing, and you can access the Internet when you power on

Then connect the cat and the hub to 2 computers and you're good to go!

If you don't have autodialing, it's a bit of a hassle

It should be achieved with dual network cards

It is recommended to buy a wireless router that is also cheap, about 100

It's better to add a route, it's troublesome in other ways, and it's not too expensive.

A router is required.

2. Click on "Network & Internet."

3. Next, open the "Network and Sharing Center", here is the function that must be used for win7 computer networking, whether it is connected to a wireless network or a broadband network, you need to open this function to set up. There are also shortcut keys here, which can be opened by clicking on the window-like shortcut key in the lower right corner of the desktop.

4. Click "Set up a new connection or network".

5. Select "Connect to the Internet."

6. Win7 will automatically search for the corresponding wireless network, click on the network with the best signal "connection" and enter the password, if the wifi does not set the password. You can access the Internet by connecting directly.

"Wireless Connectivity" means a global voice and data network that allows users to establish wireless connections over long distances, and also includes infrared and radio frequency technologies optimized for short-range wireless connectivity.

Desktops require a wireless network card.

Just find a shareware for your laptop.

The wireless router will not be sent by Telecom, and the dial-up router can go into the web page settings, but it still needs to be dialed.

I'm giving it away, and I can only use it on a single machine, and it's useless for me.

You plug the modern cable into the router (the WAN port), then plug a network cable into the router (whichever LAN port you want), and connect the other end of the network cable to the desktop.

Then enter the router interface to set up, if you have a disc, use the disc, use the wizard mode to operate, it is relatively simple. If you don't have a disc, just do it manually, enter the address in IE, or this depends on the address behind the router.

The following operation,You read the router manual.,It's very simple.,I don't want to type.,If you can't get it.,hi me.。

Laptop wireless connection network, and then add a local connection, share the wireless network to the new local connection, the network cable is poor and connected to the desktop, pay attention to the new local connection to specify another IP segment, this is more troublesome Some network cards may not support it, it is recommended not to use this way.

Sharing Internet access can be shared through the network card module of the notebook;

It's best to buy a wireless router so that both notebooks and desktops can be used, sharing method: if the host is not turned on, the other one can't be used, which is a bit troublesome.

If your desktop is also connected to the Internet with a network cable, then your desktop needs to have two network cards to be able to achieve it! Please see: Dual network card win7 sharing Internet method - use network cable to bring another computer Internet access method strategy.

The telecom network cable is connected to the router WAN port, and the computer is connected to the LAN port or wireless connection.

According to the sticker prompt on the back of the router, enter the gateway entry route in the IE address bar, usually or on the username and password sticker.

After entering, select PPPoE Internet access mode in the network parameter WAN settings, enter your telecom account password, and save.

Give your wireless a nice name in the wireless parameters and set a password to save. ok‘

Buy a 4-port router, connect it to your cat for specific settings and read the manual, the router can choose a router with wireless function, so that your laptop can use wireless Internet access, more convenient, and other computers can be connected to the router.

Buy a router, a few network cables, and a few crystal heads. Connect the network output of the cat to the input of the router with a network cable, and output it to the network cards of the two computers with a network cable at the output end of the router. Then power it on, and then set up the network of the router.

Network settings (see image below):

1。Enter the IP address of the router in a web browser (this is the one that enters mine, you look at the instructions of the router, enter the password, and also see the instructions and log in).

Point Basic Settings - WAN Settings.

In the WAN connection type - select - PPPoE (dynamically fetch IP from the XDSL ISP).

In the PPPoe account - fill in - the account number given by the telecommunications bureau and click on the PPPoe password - fill in the password of the cat (the password given by the telecommunications bureau), and then dial it automatically.

2In the LAN settings.

DHCP Server Enabled.

IP pools from (1) to (128).

Lease time () days, any few days in parentheses, follow the need to fill in the dns ** server -select -start.

DNS provides -optional-using a **server or auto-introspected server DNS 1 - fill in and can be changed as needed) to restore.

Some cats have a lot of network ports, and if your cat has more than one network port, then only one network cable is needed.

Some cats can be cracked, after cracking, let the cat dial by itself, and then you only need to buy a switch and two network cables, and you can access the Internet again, except for that, you can only buy wireless routing, there is no other way.

Without adding a route, you can add a network card to the desktop computer, which can allow the desktop computer to share the Internet.

If you don't add a router, add a wireless network card to the desktop, connect two computers, and share desktop broadband with the laptop.

No router, only desktop dual NICs. Or get a wireless card for your desktop.

You have to buy a router, if you add a cat and a good LAN interface, plug in the network cable and dial up at the same time should be able to get on!

Must buy routing, desktop connection, laptop wireless.

This is easy to do, you can get an MF and you can connect to the Internet at the same time.

Whether you use a mobile phone wireless network card to access the Internet or use a mobile phone directly to access the Internet. There are several ways to dial the number.

If that's the case, don't listen to the nonsense! It's all a bunch of stupid people.

In that case, you can only use double-click to interconnect,Go to the computer store must explain that it is a dual-machine interconnected network cable,Don't make it an ordinary network cable in vain,And then go back to home after the two machines are connected and use the laptop to open the Internet connection to share it.。

Internet connections are shared as follows:

Just enable "Internet Connection Sharing" (Figure 4) in the "Internet Options" section of Internet Explorer in the Sharing column of the dial-up network properties.

Connect to the Internet via LAN and select Auto-detect settings in LAN settings. If everything is in order, you can browse the web.

If you still can't figure it out, find a friend who will get it down, or when you buy a machine, talk to the other party and let the other party get it for you, and find a computer company to get it for you, generally not more than 50 (20-30), unless it is a big city with high consumption.