Is there anything I need to pay special attention to during the installation process when replacing

And the installation of we should pay attention to the following points: do not replace the turbocharger with a new one until the cause of the damage to the turbocharger has been determined and these causes have been eliminated.

If you do need to replace the turbocharger, follow the requirements and steps below.

To guarantee the correct and reliable installation of the turbocharger, the following procedure should be followed:

1.Pre-check turbocharger:

The turbocharger part number should match the engine.

The turbocharger should be in good condition, the rotor rotates flexibly, and the impeller is not rubbed against the shell.

2.Drain the engine dirty lubricating oil.

3.Remove the oil pan and clean it, then install it on the engine.

4.Remove the inlet and return pipes of the turbocharger, remove the oil and debris in the pipe, clean the inner pipe wall, and then install the engine.

5.Fill up a new, filtered lubricant that meets the engine manufacturer's specifications, or fill a filtered oil with a CF grade or higher.

Ensuring that the lubricant entering the turbocharger is clean is key to ensuring the life of the turbocharger.

6.Replace the lube oil filter and replace the air filter as recommended by the engine manufacturer.

Lubricants and their filters must be manufactured using products recommended by the engine manufacturer, as the use of substandard products will damage the turbocharger and engine.

7.Pre-lubricate the turbocharger inlet with clean lubricating oil.

8.Replace all seals connected to the turbocharger when installing the turbocharger. The turbocharger box contains some of the gaskets that are provided free of charge for replacement.

9.The turbocharger should be installed in the order recommended by the engine manufacturer or in the order in which the engine is **.

10.During the replacement of the turbocharger, any foreign matter should be prevented from entering the turbocharger and the various pipeline connections connected to it.

11.Start the engine at low idle for a few minutes.

12.When entering normal use, the lubricating oil and its filters and air filters should be replaced regularly according to the requirements of the engine manufacturer.

The first professional auto parts turbocharger in China, auto1998 supercharger**. At your service!

Note that the important thing is not to pay attention, the supercharger is mainly lubricated and cooled by oil, if not on the oil supercharger will be damaged in a few minutes, check the oil on the most important.

Problems such as loss of power, excessive smoke, high fuel consumption, overheating, high exhaust temperature, and oil leakage may indicate a faulty turbocharger. Changzhou E&E Turbo reminds you to correctly identify the cause of the failure before replacing the turbocharger

1.Excessive smoke.

6 1 Dirty air filter.

6 1 Air Intake System Limitations.

6 1 Flange cracked gasket fell off.

6 1 Fuel pump injector valve timing error setting.

6 1 The actuator mechanism is set incorrectly.

6 1 turbocharger damaged.

2.The engine lacks power.

6 1 The air filter is not clean.

6 1 Air Intake System Limitations.

Exhaust gas limit. 6 1 burn valve and or piston.

6 1 Flange Gasket is missing and ruptured.

6 1 Fuel pump injector valve timing error setting.

No oil leakage, no air leakage.

In performance modifications, replacing high-performance turbines or adding turbos is one of the most direct and effective means to increase power. The same self-priming engine, after adding a turbo and rewriting the computer, can often achieve the power that even a higher displacement self-priming engine can achieve. It is for this reason that many modification enthusiasts want to increase their power and run faster in this way.

The installation process will not be described here, just place the replacement kit in the designated position, tighten the screws, link the pipeline, and reset the other parts that have been removed. According to Master Huang, a tuning shop, he and his apprentice changed a turbine, and the whole work took about five hours to complete. If the owner needs to replace the intercooler or make other modifications to the engine, they will lift the engine out in its entirety and install it, which is much faster than replacing the turbo alone.

Although this article only describes the process of replacing the turbine, there are still many important points to note for fans who want to modify the turbine. First of all, not all models can be equipped with a turbine or a larger turbine to achieve the purpose of improving power, such as engine compartment space, cylinder block bearing capacity, installation matching and other problems will cause problems for construction or future use. So I recommend doing your homework before installing a turbine, looking for a success story or a ready-to-match kit that can be used, and then considering whether you need to modify the turbine.

Of course, there is also the question of whether you have enough money in your pocket to support you in doing so.