My lure throws out how it always messes up the line

The following is a personal summary of 5 drop wheel throwing skills, I hope it will be helpful to lure novices.

1. The wire cup winding should not be too full, about 2 3 or so.

2. Adjust and fine-tune mechanically first, and re-adjust mechanically every time you replace the bait of different weights, and mechanically fine-tune until the bait slowly falls.

3. Adjust the brakes again, adjust the magnetic force or centrifugal force to the maximum (if it is a double brake, all of them are adjusted to the maximum), and then slowly adjust the decrease if it does not explode, so that you can throw it farther.

4. The star-shaped force relief wrench should be adjusted well, and the unloading force is very critical when the fish is in the middle, especially for medium and large fish, I personally like to adjust the strength of about 2 catties.

5. Don't throw violently, so it's easy to blow up the line, and when the bait is about to fall into the water, hold down the line cup to prevent the line from being blown up, and practice throwing more to achieve the ability to flexibly control the line cup with your thumb, which is very effective in preventing the line from being blown up.

Spinning wheels are when you go online, the thread is twisted, so that the thread is twisted, a throw is messy, put the thread in the water as much as possible, and then reel the thread several times to use, and then don't put the thread too much, the luya nylon thread should be soft, hard, not good.

1: The memory of the thread is too strong, and the thread is naturally wound.

2: The center of gravity of the bait is not well shifted.

Summary. Hello, <>

1. Lure and fishing rod also reserve 5 to 10cm of space. 2. Hook the fishing line with your index finger, pull the wire gauge to position, and swing your arms back to make a preparatory position. 3. The casting is the same as the previous action, the fishing rod stops from 1 o'clock to 10 o'clock and releases the index finger, and throws the lure out with the elastic force of the fishing rod.

4. After throwing, use your left hand to slightly resist the outlet wheel, and use your fingers to give it a friction force to avoid the explosion of the line too quickly. 5. After Lure falls into the water, the winding gauge will be rebounded and the rocker arm will be rolled to collect the bait.

How to adjust if the line is not smooth.

Hello, <>

1. Lure and fishing rod also reserve 5 to 10cm of space. 2. Hook the fishing line with your index finger, pull the wire gauge to position, and swing your arms back to make a preparatory position. 3. The casting is the same as the previous action, the fishing rod stops from 1 o'clock to 10 o'clock and releases the index finger, and throws the lure out along the elastic force of the fishing rubber rod.

4. After throwing, use your left hand to slightly resist the side regret out of the line wheel, and use your fingers to give it a friction force to avoid the line being too fast. 5. After Lure falls into the water, the winding gauge will be rebounded and the rocker arm will be rolled to collect the bait.

Hello, <>

1. Lure and fishing rod also reserve 5 to 10cm of space. 2. Hook the fishing line with your index finger, pull the wire gauge to position, and swing your arms back to make a preparatory position. 3. The casting is the same as the previous action, the fishing rod stops from 1 o'clock to 10 o'clock and releases the index finger, and throws the lure out along the elastic force of the fishing rubber rod.

4. After throwing, use your left hand to slightly resist the side regret out of the line wheel, and use your fingers to give it a friction force to avoid the line being too fast. 5. After Lure falls into the water, the winding gauge will be rebounded and the rocker arm will be rolled to collect the bait.

Lua throws off the line, I often call it a gun, the main reasons are as follows: violent throwing, in fact, Lua does not need violent throwing, as long as the angle and strength are appropriate, the line is smooth, and the throwing distance will not be too close. When throwing, the cavity orange line is entangled with the guide ring at the top, causing the line to be unsmooth.

The bait and line are not matched, and the thin line and large bait are easy to get out of the line, and the line is damaged.

Summary. Hello , I am very happy to answer your questions for you , Mr. Xiaoshuo has helped you find the answer , the answer is as follows; Dear, after checking that the fingers are loose too late, correct: 1. Put the line and extend the distance between the bait and the tip of the rod.

2. Loose fingers earlier (recommended), it is more appropriate to loosen when the pole is perpendicular to the ground. When the spinning wheel throws the bait, the wire cup is fixed, the axis of the line cup points to the direction of the line, and when the bait drags the fishing line to fly, the fishing line is dragged out of the line cup and flies out in a spiral.

This type of delineation has no additional resistance other than the weight of the line itself, so the lure flies the farthest and has the least drag. This performance determines that the spinning wheel can throw lighter baits, but the casting accuracy of the bait is reduced.

When using the spinning wheel to cast, you should hold the rod handle, place the supporting column of the reel between the middle finger and the ring finger, and turn the spinning wheel with the other hand. When traveling during the epidemic, please be sure to do a good job of epidemic protection. I hope that Mr. Xiaoshuo's reply will be helpful to you and I wish you a happy life!

Lua is not out of the line.

Dear Hello, I am a life expert teacher Xiao Shuo, has provided consulting services for nearly 10,000 people, your question I have seen, and now I am sorting out the answer, probably Brother Xiao will take about three minutes, please wait patiently

Hello , I am very happy to answer your question , Mr. Xiaoshuo has helped you find the answer, the answer is as follows; Dear, after inquiring that the fingers are loose too late, correct: 1. Put the line, and extend the distance between the bait and the tip of the rod. 2. Loose fingers earlier (recommended), it is more appropriate to loosen when the pole is perpendicular to the ground.

When the spinning wheel throws the bait, the line cup is fixed and not ready to be stared, the axis of the line cup points to the direction of the line, and when the bait drags the fishing line to fly, the line is dragged out of the line cup and flies out in a spiral. This type of delineation has no additional resistance other than the weight of the line itself, so the lure flies the farthest and has the least drag. This performance determines that the spinning wheel can throw lighter baits, but the casting accuracy of the bait is reduced.

When using the spinning wheel to cast, you should hold the rod handle, place the supporting column of the reel between the middle finger and the ring finger, and turn the spinning wheel with the other hand. When traveling during the epidemic, please be sure to do a good job of epidemic protection. I hope that Mr. Xiaoshuo's reply will be helpful to you and I wish you a happy life!

If I'm helpful to you, please give it a thumbs up, okay? Thank you here.

You can choose to choose 10 levels of brakes to control the speed of the wire cup to the greatest extent to reduce the chance of blowing the line.

Friends who are new to Lure are prone to some situations in the process of fishing, among which the fried line is a relatively easy situation. The fried thread of a straight handle rod with a spinning wheel usually refers to the knotting of the thread, which will be more difficult to untie due to the unique spiral way of spinning the wheel. PE thread is a braided thread and is easier to knot than a nylon thread monofilament thread.

The reason for the explosion of the spinning wheel is the problem of the upper line, the upper line is too full, the upper line is uneven or the upper line is too loose. With the bait, the heavy question is clever, and the bait is too heavy to cause the thread to be buried. The GT knot is not tied properly, and the angle of the throw is incorrect.

Due to the weather, the weather is too cold and the line body is frozen. Medium and large fish, hanging bottom, putting guns, improper operation and other reasons caused by the buried thread.

Avoid reducing the frying line

Don't be too full or too little when going online, and be flat and tight according to the capacity of the wire cup and the number of wire diameters. Match the appropriate bait according to the bait weight parameters on the straight rod and tie the GT knot. Master the correct throwing posture and technique, slowly retract the line to the knot after frying the line, and then retract the bait.

If it is a submerged bait, it must be withdrawn, otherwise it is easy to hang on the bottom and cannot be rescued. After placing it on a flat place, pull out the knot and gently pull the knot to untie it slowly.

In the case of serious knotting, you can add some water to make the thread smoother, and do not vigorously resist wide wax pulling and nail touch to hurt the thread. After untying the thread joint, straighten it to see if the thread is seriously damaged. If the damage is very serious, it is necessary to re-tie the GT knot, otherwise it is easy to release the gun during the throw and run the fish when the medium and large fish are thrown.

After straightening and straightening the line, it should be leveled to prevent the secondary explosion of the line.

The adjustment method takes the magnetic brake wheel as an example, first of all, the magnetic adjustment knob is pointed to the scale 10. Let the wheels have the maximum braking force next to Yunhong. Lift the pole 45 degrees, adjust"Spindle adjustment screws"It is better to let the lure fall quickly and smoothly, and it is better to continue to rotate the spool after the lure falls into the water, only in this way can you get the best throwing distance.

The star-shaped plate can be adjusted to the tightest or has a take-up and unloading state.

The reason for the water drop wheel fried line:

The water drop wheel is a kind of horizontal wheel, and the rubber wheel next to the water drop is mainly used for lure fishing, so it is also called the lure wheel. Compared with spinning wheels, the throwing accuracy of water drop wheels is higher, the volume bridging is small, and the outlet is easy to control. The disadvantage is that the throwing is not easy to master, easy to blow up the line, the lure unloading is too loose to imitate the bait will decline rapidly, when the bait lands, the spool will be reversed to eliminate the submersion and turn to the section Na, resulting in the often said fried line.