What number of screws are installed on the license plate, and how to get on the license plate number

The screws for installing the license plate should be M6 size.

The license plate of a new car is generally four screws, and if it is caught with two, no points will be deducted and fined. Some of the new license plates of the car are four screws, and some are two screws, which are different.

For vehicles that have been manufactured or imported vehicles, as many license plate mounting holes as there are on the body, as many fixing screws are installed. Now that the new regulations are out, there will basically be four standard license plate fixing holes before and after the vehicle leaves the factory. These vehicles are installed according to the new regulations, if there are four mounting holes, only two fixed screws are installed.

The screws for installing the license plate should be M6 size. According to the "Motor Vehicle Safety Technical Inspection Items and Methods":

The self-compilation and arrangement combination of license plate number characters is divided into the following 3 types, which are three and three digits and must not be absent:

a) 3 English letters and 3 Arabic numerals.

Such as: ABC 123;

2) 3-digit Arabic numerals and 3-digit English letters, e.g. 123 ABC;

iii) 3-digit Arabic numerals and 3-digit Arabic numerals, e.g. 123 456.

The People's Republic of China Motor Vehicle Number Plate stipulates that:

a) The front license plate is installed in the middle or right of the front end of the motor vehicle, and the rear license plate is installed in the middle or left of the rear end of the motor vehicle, which shall not affect the safe driving of the motor vehicle and the identification of the license plate.

b) The license plate installation should ensure that the license plate does not have any deformation and covering, horizontal and longitudinal, basically perpendicular to the ground in the longitudinal direction, and the longitudinal angle is 15°.

The screws used for license plate installation are special anti-folding screws, estimated to be 4mm diameter screws. Generally speaking, it will be provided by the DMV when the license plate is pressed.

Hello: The screws used for the installation of car license plates are special anti-tamper screws, and the screws issued by the vehicle tube are 6mm diameter. Except for some special vehicles (such as Volkswagen Polo), the screw holes are not standard, and the others are standard screw holes.

It is 2 bags of 8 license plate screws that will be provided by the DMV when the license plate is pressed.

License plate screw installation method:

1. Prepare the screw assembly, including cushion blocks, screws, and caps, which need to be collected at the vehicle management office, and cannot be fixed with screws by yourself, if the screw assembly is not fixed in accordance with the regulations, you will face penalties.

2. The fixed point can be seen in the place where the car is hung with the license plate, and the side of the license plate with the license plate number that needs to be installed is outward, and then aligned with the fixed point of the car, and the hole in the middle is also aligned;

3. After that, insert the screws into the holes, and fix the screws with a flathead screwdriver, do not tighten them, and ensure that the screws do not fall off by themselves;

4. Then install all the screws on the other fixing points, and the screws at each fixing point are fixed first, do not tighten them, if they are tightened, it will be difficult to adjust the position;

5. After the screws are installed, adjust the position of the license plate, and then tighten all the screws;

6. Finally, press the cap to the cushion and press it into the screw, press it slightly hard, and then press the cap into and fix it, and the license plate will be installed;

7. But the car is generally two license plates, and the other can be installed after one is installed.

The screws for installing the license plate should be M6 size.

According to the "Motor Vehicle Safety Technical Inspection Items and Methods":

When registering for inspection, the license plate and license plate installation should also meet:

a) The vehicle should be provided with the front and rear license plate (frame) that can meet the installation requirements of the license plate, but the motorcycle only needs to be provided with the rear license plate (frame) that can meet the installation requirements of the license plate; The front license plate (frame) should be located in the middle or right side of the front (according to the direction of the motor vehicle), and the rear number plate (frame) should be located in the middle or left side of the back;

b) Vehicles manufactured from March 1, 2013 onwards, each license plate (frame) should be provided with at least 2 license plate mounting holes, and can ensure that the license plate is directly and reliably installed on the vehicle with M6 bolts;

c) For vehicles shipped from March 1, 2016, there shall be 4 license plate mounting holes on each license plate (frame) [except for the front license plate (frame) of three-wheeled vehicles and the rear license plate (frame) of motorcycles], and it can ensure that the license plate is directly and reliably installed on the vehicle with M6 bolts.

After the position of the license plate is corrected, fix each screw by means of a cross cone.

Prepare the license plate, screwdriver, license plate screw assembly to find the right to fix the license plate, and align the license plate with four fixed points. Rotate the screws into the anti-theft cap, then align them with the holes of the four fixing points, rotate and fix, but don't tighten too tightly, check whether the license plate is correct, adjust the alignment, and buckle the four screw caps.

The steps to install the license plate screws are as follows:

1. Prepare materials and tools: two license plates, a flathead screwdriver, and a set of license plate screw components.

<>2. Find the place where the license plate is fixed before and after the car, especially the 4 fixed points on the license plate.

3. Align the license plate with the fixed point of the license plate on the car, align the license plate, and prevent dislocation after alignment, which needs to be supported by hand.

4. Insert the screw rod into the hole at the fixed point of the car itself.

5. Use a flathead screwdriver to fix the screws.

6. Use the same method to screw all the other 3 fixing points, and pay attention not to tighten them too tightly.

7. Finally, check whether it is aligned and adjust it slightly.

8. Buckle the four screw caps in turn.

According to their own models, the Ministry of Public Security promulgated on September 19, 2008 and implemented on January 1, 2009 the "special sealing device for motor vehicle number plates" (GA804-2008) industry standard, which stipulates that at least two license plate sealing devices should be used for each license plate. Due to the different structure of the vehicle, if it is stipulated that each license plate uses 4 license plate sealing devices, it is inconvenient to operate.

In accordance with the provisions of the national standard, the motor vehicle license plate should be fixed with a special motor vehicle sealing device issued by the vehicle management department, and the 4 mounting holes of each license plate should be installed with a sealing device, except for the restrictions of the vehicle conditions, some vehicles only have two holes, and two screws can be installed.

The new regulations only clarify that the installation of license plates cannot be blocked, and increase the penalties for blocking license plates, which have changed from the original 6 points to 12 points at a time, and there are no specific provisions on the license plate on several screws. The last four screws were stipulated in a notice of the GA department more than a year ago, and they were not strictly enforced, and my vehicle passed the annual inspection in 12 years, and it did not say that it must be on the four screws.

The above content reference: Encyclopedia - special fixed sealing device for motor vehicle number plates.

The car supports several installation screws, so you have to install a few, and there can be no gaps.

Order No. 123 of the Ministry of Public Security, which came into effect on January 1, 2013, has strictly stipulated the deduction of points for road traffic safety violations, in which 12 points will be deducted at a time if the motor vehicle driven by the driver of a motor vehicle is not installed with a motor vehicle number plate in accordance with the regulations. However, according to the relevant provisions of GB7258-2012, starting from the 43rd month from the date of implementation of the standard, each license plate (frame) of newly produced motor vehicles (except motorcycles) (except for the front license plate [frame] of three-wheeled vehicles) shall be equipped with 4 license plate mounting holes. According to the provisions of the public safety industry standard GA36-2007 "Motor Vehicle Number Plate of the People's Republic of China" and its No. 1 amendment list, the installation holes of metal material license plates shall be installed with a fixed sealing device in accordance with GA804, except for those that cannot be installed due to vehicle conditions.

According to the relevant experts of the municipal traffic management department, the most basic requirements for the installation of fixed screws on motor vehicle license plates are: 4 screws must be installed if there are 4 holes in the vehicle number plate frame, and only 2 holes need to be installed with 2 fixed screws. If there are only 2 holes, it should belong to "except for those that cannot be installed due to vehicle conditions".

The car supports several installation screws, you have to install a few, there can be no vacancy, some cars are 2 in front and 4 in the back, depending on the actual situation of your car!

The most standardized: installed in a designated location; The front and back should be fixed with 4 screws (the fixing screws have disposable special screw caps); There is no word on the license plate holder. But look where you are.

For example, in Chongqing, as long as it is installed in the designated location, the word "good brand" is not blocked. Henan may be stricter, and any of the above may be punished if there is a discrepancy.

There are 4 anti-theft screws on it, and the license plate frame should not be brought.

It doesn't seem to be deducted points now, and the new requirement is to install four screws. However, some license plates cannot be fitted with four, and the back part is suspended.

The car supports several installation screws, you have to install a few, there can be no vacancy, the specific situation of your car shall prevail!

It doesn't seem to be deducted points now, and the new requirement is to install four screws. However, some license plates cannot be fitted with four, and the back part is suspended.

Those who can go up to 4 must go to 4, and those who can't go up to 4 must go up to 2.

The front and back should be fixed with 4 screws (the fixing screws have disposable special screw caps);

After getting the license plate, in fact, someone in the vehicle management office is responsible for the license plate, if you want to save trouble, just let them help you get on it. Let's talk about the installation method of the license, generally speaking, there are four ways to get the license.

1. Use self-tapping screws for installation.

At present, this method is the most common, and the advantage is that the installation is simple and convenient, as long as there is a change cone, it can be installed smoothly. Disadvantages: The firmness is slightly poor, and it is easy to lose screws or license plates according to the road section that has reacted to the stagnant water.

The method is: first put the license plate buckle on the license plate holder, and then add a rubber pad or stick several layers of double-sided tape behind the license plate, (the main purpose is to prevent the license plate from colliding with the bumper when driving), and then the self-tapping screw passes through the anti-theft - through the license plate holder - through the license plate (- through the shock absorbing rubber pad) - the expansion plug of the bumper, tighten it directly, and after the above two self-tapping screws are tightened, cover the cover of the anti-theft risk. The law is the same as that of the front and rear licenses.

2. Use self-tapping screws + anti-theft bolts for installation.

The advantages of this installation method I have are: firm installation, rust-proof, and anti-theft ability. Cons:

Anti-theft bolts need to be solved by themselves, especially stainless steel anti-theft bolts, nuts, gaskets, and spring gaskets need to be made of stainless steel. The installation is more complicated, it needs to be punched, and the car needs to be installed on the shelf or on the ditch.

Installation method: the top uses self-tapping screws, the following uses anti-theft bolts, the installation method is basically the same as the self-tapping screws, it needs to be explained that the front bumper needs to be punched under the 2 screw positions, you must be careful, the original position is for long self-tapping screws, there is a barrel-like plastic column. It is best to go to 4S to let the masters help you get the anti-theft bolts, to remove the plastic partition under the front of the car, and then put your hand into the upper gasket-spring gasket-nut.

The back bumper is relatively simple, remove the 2 plugs on and below the bumper, the screws can be directly inserted in, and the gasket-spring gasket-nut can be applied from the inside of the bumper by hand.

3. Riveting. At the DMV, it can help you rivet the license plate to the bumper. The advantages are: firm installation and beautiful appearance. Disadvantages, it is difficult to find tools by yourself, and after the bumper is damaged, I am afraid that you will have to re-rivet it or install it by other methods.

Install the French side and rivet it directly with a riveting gun.

4. Bonding. I guess this method is rarely used, but I think it's a very simple way to glue the license plate to the bumper. Pros:

The method is simple, no need to use rubber pads and other shockproof, easy to operate. The downside is that if the bumper is broken, I don't know if it will get thicker when taking pictures. If you choose adhesive, you need to be able to bond metal and plastic, and be waterproof and oil-resistant.

Tools required: matching screws, screwdrivers.

1. First of all, find the screw holes on the front face of the car, as shown in the figure below

2. After that, attach the license plate to the screw hole, as shown in the following figure:

3. Insert the screw rod into the hole at the fixed point of the car itself.

4. Then use a screwdriver to tighten it slightly, but not too tightly, so that it can be adjusted for a while.

5. Twist the screws of the remaining 3 holes at a time.

6. Then adjust the license plate to make sure the license plate is correct.

7. Then cover the screw cap, as shown in the figure below

8. In this way, the license plate is installed, as shown in the figure below