How to fix faucet leakage, how to fix faucet leakage

Q: Should I replace a leaky faucet immediately? a：

There are many reasons for faucet leakage, once the leakage is found, you should first check which part is wrong, and replace the accessory. The most common is caused by damage to the water-stop tape that ties the faucet part (fixing screw). In this case, simply remove the faucet with a wrench and re-roll the new water-stop tape where the fixing screws are.

If the faucet is tightly tied, the cause of the leakage may be a leak at the outlet, which is generally caused by the wear of the shaft gasket in the faucet. In this case, you can use pliers to loosen the gland and remove it, take out the shaft gasket with a clip, and replace it with a new shaft spacer. In addition, it may be that the triangular gasket in the gland is worn and the water leakage in the lower part of the faucet tether.

In this case, you can loosen the screw and remove the tie, then loosen the gland and remove it, and then take out the triangular seal on the inside of the gland and replace it with a new one. Q: Why is it still leaking after I have replaced the entire faucet?

A: Some water leakage problems have nothing to do with the faucet itself, it may be caused by improper installation of the water hose and the faucet body. In addition, it can also be caused by problems such as aging, unstable water pressure, or corrosion of the water hose that supplies water to the faucet.

Once the water hose cracks, bursts and other problems, the consequences will also be serious. Therefore, experts recommend checking or replacing the water hose every 1-2 years or so.

Q: How should I use the faucet correctly? a：

Some citizens like to tighten the faucet tightly every time they run out of water, thinking that this will prevent water leakage. In fact, the correct use of the faucet should be turned off and opened as gently as possible, do not rotate the faucet knob vigorously and repeatedly, and should not rotate the faucet too tightly. In addition, the faucet should try not to bump into hard objects.

For the use of the bathtub faucet, the metal hose of the shower head should be kept in a natural stretched state, do not coil it on the faucet when not in use, and pay attention to the joint between the hose and the valve body when using or not in use, so as not to break or damage the hose.

What to do if the faucet is leaking? Teach you a trick to solve the water leakage problem easily.

The reason why the faucet is buzzing and leaking:

The faucet does not come out of the water smoothly, and the shock wave is generated, and the frequency of the shock wave is the same as the resonance frequency of the pipe, causing the pipe to resonate and make a sound.

The lack of pressure in the faucet pipe causes the sound of water in the water pipe flowing backwards.

You can see if the noise of the faucet is caused by the wrong size of the faucet gasket or if the gasket does not fit snugly on the faucet core. If this is the case, the noise can be eliminated by replacing it with a new gasket or by fitting it snugly.

Workaround:

Drain the air from the faucet pipes.

Faucet production process:

Copper ingots Dissolving Casting (low-grade castings, high-quality faucets are cast by gravity) Processing Cleaning Casting tolerance inspection after casting inspection Leak tester Electroplating surface inspection Electroplating inspection Assembly Water testing and leak testing Finished product inspection Packaging Factory.

Precautions: 1. Don't use too much force to turn the faucet on and off, just turn it gently. Even a traditional faucet doesn't require a lot of effort to wring it to death. In particular, do not use the handle as a handrail to support or use.

2. The metal hose of the shower head of the bathtub faucet should be kept in a natural stretching state, and it should not be coiled on the faucet when not in use. At the same time, when using or not in use, pay attention to the joint between the hose and the valve body to avoid breaking or damaging the hose.

3. Under the condition that the water pressure is not lower than that, after a period of use, if it is found that the water output decreases, or even the water heater goes out, you can gently unscrew the screen cover at the water outlet of the faucet to remove impurities, and it can generally be restored as before.

4. Experienced and qualified professionals should be invited to carry out construction and installation. When installing, the faucet should try not to bump with hard objects, and do not judge where to leave cement, glue, etc. on the surface, so as not to damage the surface of the surface plating gloss. Pay attention to remove the debris in the pipe and install the faucet.

The above content reference: Encyclopedia - Faucet.

A leaking faucet is an annoying thing, if it is a small leak, it is better, and you can cope with it for a short period of time with a small basin to catch water; If it is a big leak, a lot of water will be wasted, so what should I do if the faucet is leaking? If you know how to leak faucets, check the general first, and judge whether it can be repaired; If not, directly find a master to repair. Here are the repair methods for faucet leaks, you may wish to take a look.

1. What should I do if the faucet is leaking?

1. Faucet leakage will cause a lot of waste of water resources, but also bring a lot of inconvenience to life, in fact, the faucet structure is simple, under normal circumstances, as long as the new faucet, the internal shaft gasket, or triangle gasket and other gasket parts are good, you can solve the problem of water leakage.

2. If the faucet joint is leaking, mainly because the water-stopping tape that ties the fixing screws of the faucet part is damaged, you need to remove the faucet with a plate plier and re-roll the new water-stopping tape in the place where the screw is fixed.

Second, the faucet leakage repair steps.

1. The faucet is generally a press-type faucet, taking the press-type faucet as an example, a brief introduction to the faucet leakage repair method, first prepare the tools, there are pliers, screwdrivers, penetrating lubricating oil, movable wrench, and the gasket to be replaced.

2. Close the water inlet valve.

1) First remove the small screws on the top or back of the faucet handle, so as to remove the handle fixed on the main body of the faucet, some screws are hidden under the metal buttons, plastic buttons, or plastic sheets, and these buttons or plastic sheets are snapped into or screwed into the handles.

2) As soon as the button is opened, you will see the handle screws mounted on the top, if necessary, use some penetrating lubricating oil like WD-40 specification to make the screws loose and easy to remove.

3. Remove the handle.

1) Remove the filling nuts with large carp pliers or adjustable wrenches, do not leave scratches on the metal to avoid accelerating oxidation, and turn the valve core or shaft in the same direction as when you turn on the faucet to unscrew them.

2) Look at the parts of the faucet, remove the screws that hold the washer in place, and if necessary, use penetrating lubricating oil to loosen the screws. When inspecting the screws and spools, replace them with new ones if they are damaged.

4. Replace the gasket.

1) Replace the old gasket with a new washer that is exactly the same, a new gasket that almost exactly matches the old washer can generally stop the faucet from dripping, and also pay attention to the old washer, whether it has an inclined plane or a flat plane, and replace it with the same new washer.

2) The gasket designed only for cold water will expand violently when hot water flows through it, blocking the water outlet and slowing down the flow of hot water; Some gaskets work in hot and cold water, but make sure that the gasket you buy is the same as the original gasket.

5. Install the faucet parts.

Attach the new gasket to the spool, reinstall the parts in the faucet, rotate the spool clockwise, and when the spool is in place, reattach the fill nut so that the wrench does not leave scratches on the metal.

1. The faucet aerator is leaking. Water leaks around the faucet aerator, mainly because the gasket of the faucet aerator is worn or aged. Generally, there are gaskets in faucets, but in this case, you can just replace the gasket again.

Then remove the old gasket and replace the new gasket, paying attention to choosing a washer with the same size. Some faucets have washers that are fixed with nuts and screws, pay attention to them before replacing them, and remove them after loosening them.

2. The faucet is not closed tightly. If you find that the faucet is still leaking after replacing the gasket, it is likely that there is a problem with the ceramic sheet under the gasket. Then it is necessary to replace the corresponding ceramic spool.

3. Other reasons. If you feel that there is always a gap in your faucet that is leaking, it may be due to damage to the O-ring. The O-ring is at the point where the base and the faucet interface exit, if it is damaged, the O-ring can be replaced by the above steps.

The faucet leakage may also be the damage of the water-stop tape of the faucet part, at this time, it is necessary to replace the water-stop tape, after removing the faucet, roll the thread part with wind printing tape 5-6 times along the clock.