In 2014, the new Sylphy wants to change the engine coolant, how to operate?

Hello, 2014 new Sylphy, replace the engine coolant first put the original clean, the inside of the cylinder block is also clean, add when starting, exhaust, you can go.

When replacing the antifreeze, Sylphy first removed the bottom cover of the engine, and then opened the radiator drain plug at the bottom of the radiator tank, which is located on the right side of the direction of the vehicle, so that the vehicle can be seen clearly when it is lifted. Then remove the tank cover, wrap a thick cloth around the tank cover, slowly turn the tank cover a quarter of a turn to release the accumulated pressure, and then unscrew it completely. Never remove the water tank cover when the engine is hot, high-pressure engine antifreeze will spray out of the water tank and may cause severe burns.

When filling antifreeze, clean and install the radiator drain plug, if there is a washer, it is best to replace the screw washer, check whether the hose clamp has been firmly tightened, raise the heater hose as much as possible, and fill the antifreeze into the "max" position of the reservoir (approximately, install the water tank cover, turn on the engine to warm up for ten minutes, idle 3000 rpm, and set the heater temperature controller at the "cool" and "warm" positions, check the sound of the engine antifreeze flowing, and continue to replenish after the liquid level drops.

Note: Some antifreeze coolant needs to be used proportionally with water to play an "effect", and many car owners buy it back and use it directly without reading the manual, which eventually leads to the engine "boiling", so no matter what kind of antifreeze coolant you buy, it is best to read the manual before use to ensure that nothing goes wrong.

If your 14th Gen Sylphy is running low on coolant, you need to take the following steps as soon as possible:

1.Check the cooling system for water leaks. It is possible to inspect the engine compartment for visible water stains or traces of water, or to check for signs of water leaks under the ground. If a water leak is found, it needs to be repaired or replaced in a timely manner. Congratulatory matching.

2.Inspect the cooling system's water tank, water pipes, pumps, etc. for cracks or breakages. If a problem is found, it needs to be replaced or repaired in time.

3.If the coolant is insufficient due to evaporation or consumption, the right amount of coolant can be added. However, it should be noted that when adding coolant, you should choose the same type of product as the original coolant, and add it in strict accordance with the requirements of the manual.

4.It is advisable to inspect the cooling system for impurities or dirt when adding coolant and to clean it if present.

It is important to note that if the coolant is in a constant state of insufficiency, it will cause the engine to overheat, which in turn will cause damage to the engine. Therefore, it is necessary to find and solve the problem of insufficient coolant in time to ensure the normal operation of the engine and driving safety.

The replacement method of Sylphy antifreeze is as follows: open the water tank cover, drain the old coolant, fill with new coolant, and install the water tank cover. To replace the antifreeze in some cold areas, you can warm up the car for about 5 minutes, but be sure to turn off the engine when replacing it, and replace it after cooling to avoid being scalded by high-temperature coolant or steam.

The specific operation steps are as follows: 1. Open the water tank cover: remove the engine bottom cover, open the radiator drain plug at the bottom of the water tank, and then remove the simple combustion cover of the water tank.

2. Drain the old Suiqi coolant: find and open the coolant drain screw, generally on the rear side of the engine, if you need to discharge faster and more thoroughly, you can add distilled water from the coolant filling port to clean, blow out the excess coolant with a Fengchailing gun, it should be noted that the air pressure should not be too large, so as not to damage the internal parts of the system. 3. Add new coolant

After tightening the drain screws, add new coolant from the filler port, which is generally recommended not to exceed the "max" position (approx. 4. Install the water tank cover: open the engine to warm up for about 10 minutes, idle speed 3000 rpm, if the fan starts to rotate, indicating that the coolant has reached the normal temperature, at this time, tighten the filling port cover, and install the water tank cover.

Ten years or 200,000 kilometers of coolant for the original car.

Nissan Sylphy antifreeze is located under the engine compartment near the fuse box, is a liquid tank with a white liquid filling port and blue coolant storage, the antifreeze reservoir bottle has the max and min letter logos, and the antifreeze can be filled to the middle of the two signs.

Nissan Sylphy antifreeze is located under the engine compartment near the fuse box, is a liquid tank with a white liquid filling port and blue coolant storage, the antifreeze reservoir has the max and min letter marks on the bottle, and the antifreeze can be filled to the middle of the two signs. The Nissan Sylphy is a compact family sedan owned by Nissan, this car has a wheelbase of 2712 mm, and the length, width and height are 4641 mm, 1815 mm, and 1450 mm respectively. The front suspension of this car uses MacPherson independent suspension, the rear suspension uses torsion beam non-independent suspension, and the rear suspension uses torsion beam to expand the rear seat space and trunk space.

The Nissan Sylphy coolant filler is white and the reservoir is filled with blue coolant. The coolant reservoir has the letters "MAX" and "MIN" on the body, and the coolant can be filled to the "MAX" position. When it comes to adding antifreeze coolant, there are precautions here, that is, do not mix antifreeze coolant between different brands and models to avoid the failure of antifreeze coolant due to different chemical compositions.

If you switch to a different brand of antifreeze coolant, it is best to drain the antifreeze coolant inside the engine beforehand and clean all cooling lines before adding it.

Photo by Q&A) M5 Trumpchi GS8 AION V Macchiato DHT PHEV Latte DHT Hiphi X @2019