How to install the inner strings of the erhu? How to restore the original tune?

Hook the ball at the bottom of the barrel and thread the other end into the hole in the shaft (note that the outer strings are on the outside and the inside strings are inside), and then turn. ** When holding the string with your right hand. On the Internet, a timpani system can be set.

<> "This is the timpani. ^ω

At first glance, you are a beginner. Erhu can't disassemble both strings at the same time and reinstall the pro

You can put the end of the inner string without a loop into the hole of the top handle, and then pass through the daughter, and then put the bow between the two strings, and then pull the end of the inner string with a circle all the way to the bottom, and put it on a bolt below, so that's it, as for tuning, if you have the conditions, go to buy a tuner, or go to the next standard tone on the Internet, I have this I can send to you, when tuning, you can hurry up at the beginning, and take your time when it's a little tight, and use the greatest strength to turn the smallest amplitude, One is to tune out the standard tone, and the other is to prevent the string from breaking.

Pull the strings with color and space, the thicker strings, up from the bottom, put the horse away, put the bow between the two strings, then pass through the gold, pull to the tuner, then put the tuner up, pull it to the top, go through a small hole, and it is installed.

Tuning, if the standard amplitude of the tone is small, use a tuner.

Find a tuner on the computer, or find a piano**c, the d on the right side is the tone of the strings, as for how it depends on whether you are a wooden shaft or a machine shaft.

The length left on it is as long as it doesn't get in the way, there are no hard and fast rules.

1. Open the string package, pay attention to the strings are divided into inner strings and outer strings, the outer string is a small one, and the inner string is a thick one. Be careful after opening the ramp to prevent the strings from bending.

2. Install the outer strings first, and put the small ring at the end of the outer strings (thin strings) on the screws under the erhu bottom bracket, not on the piano shaft first, and then straighten it up to the piano shaft. The outer string is fixed on the lower shaft, insert the string head into the line hole of the lower shaft, pass through and then pull back to insert the headstock, note that the beat accompanies the state to never pass through the exposed string head, turn the shaft, and make it clockwise.

from the inside out) around the shaft and tightened.

3. Install the inner string again, put the inner string (thick string) string tail ring on the screw in the middle at the bottom of the erhu, and then straighten it to the piano shaft, the inner string is fixed on the piano shaft, insert the inner string head into the wire hole of the upper shaft, pay attention to the string head not to be exposed, turn the piano shaft, wrap it counterclockwise (from the outside to the inside) around the piano shaft, and tighten it.

4. After installing the inner and outer strings, tighten the small screws that hold the strings at the bottom of the erhu to prevent the strings from loosening. Tie the strings with a thousand pounds, pad the sound muffling pad, do these things, the string installation is completed, and finally adjust the timbre, you can play the music.

Maintenance of erhu strings:

1. After each playing, use a cotton cloth to remove the sweat and rosin on the strings.

Wipe it clean in time, because slightly inferior strings rust quickly, and rusty strings will affect the pronunciation of the erhu; For example, empty strings.

The pure fifth is very accurate, but when pressed to the middle octave of the string.

The same finger note will be slightly lower when the outer string is dirty, which means that the string vibration frequency is reduced due to dirty or rusty strings, and such strings need to be replaced.

2. In ordinary times, you should develop the habit of rubbing rosin before pulling the erhu, and make sure that the bow hair is white, but not too much, because if you rub too much, there will be noise. The pronunciation of the erhu is transmitted to the saddle by the vibration frequency generated by the friction between the bow hair and the string, so that the resonance between the skin and the barrel and the sound.

How to install the erhu strings:

1. First of all, we open the packaging of the strings, pay attention to the strings are divided into inner strings and outer strings, the outer strings are thin, the inner strings are thick, after opening, be careful to prevent the strings from being bent.

2. Install the outer strings first, change the outer strings (thin strings) strings to clear the tail and put the small ring on the screws on the outside under the erhu bottom bracket, do not wear the shaft first, and then straighten the strings to the top of the shaft. The outer string is fixed to the shaft underneath, insert the string head into the wire hole of the lower shaft, pass through it, and pull back into the headstock. Be careful not to cross the string head, and then turn the shaft, clockwise around the shaft.

from the inside out) to tighten it.

3. Insert the inner strings, put the small ring at the end of the inner string (thick string) on the screw in the middle at the bottom of the erhu, and then straighten it up to the piano shaft. The inner string is fixed to the upper shaft, and the inner string head is inserted into the hole in the thread before the upper shaft nucleus is slipped. Be careful not to expose the head of the string, then turn the shaft and make a circle around the shaft counterclockwise (from the outside) and tighten it.

4. Tie the strings to a thousand catties.

The inner chord of the erhu is installed on the upper chord shaft in order to leave the distance on the upper part of the jack rope, which is convenient to operate when the tone is aligned.

The two strings of the erhu are divided into inner and outer strings, the inner strings are wrapped around the upper shaft, which is counterclockwise when wound, and the outer strings are wound in the lower shaft in a clockwise direction when tightened, and are counterclockwise when tightened. In this way, in order to leave the distance on the upper part of the jack rope, it is convenient to operate when the tone is right, and after winding, it is required to tie the jack rope, and you can start to match the tone. The inner string of the erhu is wound around the upper axis, and the outer string is wrapped around the lower axis.

Introduction and use of erhu

The erhu is a bowed string instrument of the Mongolian people in northern China, also known as strings.

or Huqin. It is composed of a barrel, a holder, a stem, a jack, a saddle, a stem, an inner and outer string, an inner and outer string, and a bow and a bow.

The erhu is generally played in a sitting position, holding the piano in the left hand, the tiger's mouth is stuck at the jack, the four fingers are pressed on the strings respectively, the right hand carries the bow to play, and the bow hair is rubbed against the strings to make a sound. Playing the erhu should pay attention to intonation and rhythm. There are also erhu performance techniques.

For example, the fingering of the left finger is changed, and the right hand bow is the pause bow, jumping bow, throwing bow, and even the bow of the right hand.

After using the erhu, wipe off the float, put it in the piano case, and then put it in a ventilated and dry place. The bow hair of the erhu should retain the rosin fragrance that has not been washed away.

But not too much. The strings of the erhu are changed once a year or so. If the skin of the erhu is dry, rub some vegetable oil.

Erhu outer stringsHere's how to install it:

Step 1: Open the newly bought strings, try to be careful when opening them, and don't bend the strings.

Step 2: Install the outer strings, first put the small ring of the outer string (thin string) string tail on the screw under the bottom bracket of the erhu, not first wear it on the piano shaft, and then straighten it up to the piano shaft, the outer string is fixed on the piano shaft below, insert the string head into the line hole of the lower shaft, pass through and then pull it back and insert it into the piano head, pay attention to Zhaoyou do not pass through, just hide the string head in it, turn the piano shaft, and tighten it clockwise (from the inside out) around the piano shaft.

Step 3: Then turn the inner string, put the inner string (thick string) string tail ring on the screw at the bottom of the erhu, and then straighten it up to the top of the piano shaft, the inner child is fixed on the upper shaft, insert the inner string head into the line of the upper shaft, in the middle, turn the piano shaft, and wrap the first counterclockwise (from the outside to the inside) around the polyshaft to control it. Note that it should not be tightened too tightly, it is easy to break the strings, and you can straighten it.

Step 4: The small ring of the string is set on the bottom bracket screw and then goes to the end of the piano shaft to be fixed and easy to run, you can hook the string on the screw and clamp the barrel with both legs to prevent the string from falling out, you can easily install the other end. Poor front.

Supplement] The strings of the erhu are divided into inner strings and outer strings, the inner string is a string close to the inside when we play the erhu, so it is called the inner string, the outer string is the same, the inner string is the relatively thick one, and the outer string is the relatively thin one.

Summary. The A sound (440h) of a small character group of standard articators (timpani, whistle, tone, etc.) is used as the standard tone, which is the 5s tone in the D key.

According to your own judgment of the outer string tone, by rotating the outer string axis of the erhu, (if it is low, the string is twisted, if it is high, the string is loosened), the rotation amplitude is not too large, and the outer string is gradually adjusted to a pitch equal to the standard tone while listening.

Then, using a standard articulation device, the same method is used to tune the inner string tone to the D note, which is the 1do note of the D key.

How to adjust the inner and outer chords of the erhu?

Hello, I have seen your question and am sorting out the answer, please wait a while

The A sound (440h) of a small character group of the standard pronunciation dismantler (timpani, whistle, tone, etc.) is used as the standard tone, which is the 5s tone in the D key. According to his own judgment of the outer string tone, by rotating the outer string axis of the erhu, (if it is low, the string is twisted, if it is high, the string is loosened), the amplitude of the rotation of Lu Sui Nian is not too large, and the tuning family Jane gradually adjusts the outer string tone to a pitch equal to the standard tone. Then, using a standard articulation device, the same method is used to tune the inner string tone to the D note, which is the 1do note of the D key.

Hello dear<>

The answer you are looking for: The method of erhu installation and tuning is as follows:1

Installing the Bow: Insert the bow into the barrel and tighten the bow hairs. 2.

Attaching the strings: Tie one end of the string to the post, then cross the string over the bridge and tie the other end to the tuning shaft. 3.

Adjust the strings: Tune the strings in a standard pitch order, starting with the treble string and up to the bass string. You can use a tuner or tuning fork to assist with tuning.

4.Adjust the bow history: Tighten the bow, then gently pull the string with the bow to check whether the bow hair is even, if it is uneven, you need to adjust the bow hair.

5.Adjust the tone: Adjust the tension of the strings as needed, which can be adjusted by plucking the small rings on the strings.

It is important to note that care needs to be taken when installing and tuning the strings to avoid damaging the bow and strings. If you are not familiar with the operation of installation and tuning, it is advisable to seek help from a professional instrument repair shop or teacher.

Summary. First, take out the inner strings (slightly thicker) and outer strings (slightly thinner) of the erhu, straighten them straight, and hook the heads of the rings of the inner and outer strings on the left and the outer strings on the right according to the inner strings on the left and the outer strings on the right, respectively, and then lift them up along the card slot. When you arrive at the approximate position of the Qianjin line, you will still follow the previous order, and do not entangle the strings, otherwise it will cause the erhu sound quality to be unavailable.

First of all, take out the inner strings (slightly thicker) and outer strings (slightly thinner) of the erhu, and straighten them straight, according to the inner strings on the left and the outer strings on the right, respectively, the ferrule head hook sedan slid the inner and outer strings into the two screw ports under the erhu bottom bracket, and then lift them up along the card slot. When you arrive at the approximate position of the Qianjin line, you will still follow the previous order, and do not entangle the strings, otherwise it will cause the erhu sound quality to be unavailable.

Then, the string heads of the inner and outer strings pass through the shaft hole respectively, according to the upper shaft rotate clockwise, and the lower shaft rotates counterclockwise, that is, the principle of "up, inside, down, outside", turn the strings in turn until the vertical oak finally the strings are straight and do not slide for good leakage.

You have to pay attention to the following points: 1. Turn the strings to master the strength, and do not turn the strings too much and cause the strings to break and hurt your eyes. 2. The strings wear through the shaft hole, pay attention to pressing the string head when winding the strings behind to prevent the string head from piercing your hands.

3. When replacing the strings, you should take off one first, and replace one first, so that it is not easy to loosen the kilogram. 4. After replacing the strings, if there is noise in the empty strings, it is basically certain that the thousand moves are loose. It is recommended to re-tie a thousand pounds.

5. After replacing the strings, if there is noise in the inner strings, it may be that the inner strings are twisted and uneven. It is necessary to loosen the inner chord from the bottom bracket, straighten the inner chord, and then tighten it.

Oh. This is already more detailed.

It's a hard wound.