When the heating of the newly renovated house is tested for water, what happens when the last set of

If it is the last group of heaters, there is no water and no gas, there are only two possibilities.

The first possibility is your radiator.

The blockage has been found inside, and at this time the radiator can only be replaced, because there is no way to remove the clogged items with something like this.

The second possibility is that the pressure of the water is not reached. Because our radiators are extended from low to high angles, when it comes to the last group, the pressure of the water may not meet the requirements, so at this time we generally use two ways. Add booster pumps.

Or adjust the angle. It can also raise the water level of our heating.

In the newly renovated house, when the heating is tested and there is no water in the last group of heating, then it may be that the pipeline is not connected, and it is best to check the pipeline.

In the case of your home's heating, it may be that the last set of heating is blocked, or it may be holding the air. You first deflate the last set of heaters, and see if it can be good after exhausting, if it is not good, you have to find a professional repairman to dredge it.

The laying of heating pipes is more demanding, the pressure test must be strict, can not be sloppy, you said the last group of radiators water, gas is not passable, that is, the radiator is blocked, if you are not sure where there is blockage, just replace it, and then replace it with a group of unobstructed on the line.

If it is a newly installed heating, you have to find a heating installation to see, if the heating is original, find the property to check it, generally new heating, you have to suppress the test.

You should thoroughly check that there is a possibility of air in it. Just let the air out, and you can get in the water.

It should be caused by the valve being closed and not ventilating

Newly renovated house, when the heating stops bleeding, the last group of heating has no water and no gas garbage on the heating pipe is equipped with problems, there is a problem in the middle of the way, the phenomenon, how can you ask the maintenance master to come and inquire about the reason.

There must be no passage, or there is air in it.

Check if the valve is open, there should be no other problems.

Then you have to find the person who decorated your heating line to find faults.

It means that the heating installation method you installed is not right, there are rules for making socks jujube radiators**water inlet** water outlet, and the inlet and outlet water depends on the structure of the radiator. As shown in Fig.

The heating gas installed by yourself has been put into the water several times, and there is no water and no gas when the water heating is added in the middle of the destruction.

In the case of your family's Nasun heating, it may be that the last group of heating is blocked, and the cave chain may be holding its breath. You put the last set of heaters on the hono gas first, and see if it can be good after exhausting the gas.

Ask the great god himself to guess the heating installed, put the finch type water a few times, and then add water to the finch bridge to heat the water, there is no water, and there is no gas, what's going on? That's when the heating in your house is blocked, and it's not just when it's exposed.

Ask the great god to install the heating himself, put the water a few times, and then add water, the heating will run out of water, you have no gas, how can this number stop Bi Heng? It could be that you have a problem with your air pressure, or it could be that Jane is not working well with you.

I put water on the heating installed by myself a few times, and then there is a shortage of water, and the heating is filial piety without water, and there is no gas problem, I personally think that there is nothing without gas This is not terrible.

I feel that the heating installed in my home has been put in the water several times, and then the water heating is gone, and there is no water, so I should find a professional.

I installed the heating myself, put water a few times, and then add water and heater to have no water, and there is no gas, what's going on? You must have taken it wrong.

I think in this case, you still haven't picked it up, or you haven't handled it well, you find a professional to do it for you.

This is because its water is circulating, and if you pour it out, he will run out of water and will not be able to use it.

Are you heating yourself? If not, you can call the property ** to help solve it.