The bathroom is damp and moldy, do you know what causes it?

The bathroom is damp and moldy, do you know what causes it?

1.Due to the lack of air circulation, the toilet must be ventilated in time after use. Bathroom floor drain.

Inadequate installation: The installation of floor drains in the bathroom is very important, especially in the shower location. When installing, make sure that the floor drain coincides with the sewer pipe, so that the ground drainage can directly enter the sewer pipe, and there is no problem that the floor drain is disconnected from the sewer pipe.

When installing, the floor drain is placed directly on the cement mortar.

layer, and then when bathing, it will enter the cement mortar layer to drain it, which will naturally leak out, causing the floor to be damp.

2.Bathrooms are the most frequently used and humid home environments, and often produce pungent musty odors due to poor ventilation, humid climate, etc. Restroom humidity and mildew are mostly caused by poor ventilation.

In order to enhance ventilation, we all install exhaust fans above the restrooms.

Most modern apartments have a limited bathroom area. If it is not installed properly, there will be problems such as messy countertop flooring, moldy rust, and difficult to clean sanitary dead corners, which reflects the importance of dry and wet separation in the bathroom. The "bathroom" with dry and wet separation is becoming more and more popular.

In addition to drying and hygiene, it is more important to alleviate the pressure of home use during the morning and evening rush hours, and bring comfort and convenience to the family.

3.Separating the dry and wet areas of the restroom can better block water vapor.

It is also very convenient to clean, which effectively prevents the problems of mildew, dampness and odor in the bathroom. Every home will have a "peak period" of restroom use. The reasonable design of dry and wet separation is convenient for families to use the toilet at the same time, which greatly improves the efficiency of using the toilet.

In fact, it is not difficult to understand that there is moisture regain and mildew at the door of the bathroom. The main reason is that the moisture in the bathroom penetrates into the wall outside the door, and the reason for the water leakage must be that the waterproof work is not in place. If the bathroom has heating, the underfloor heating pipes must be under the floor tiles.

Once the water pipe is damaged, it will leak and the wall must be wet.

Because the air inside the bathroom is not circulated, the humid gas cannot be volatilized after washing and bathing, and his position is also more oriented to the cold and damp corner, it may also be caused by water seepage on the ground, and the bathroom is too wet.

Poor ventilation in the bathroom, no ventilation equipment is installed, water stains are not cleaned up in time, and it is in a damp state for a long time, all of which will lead to dampness in the bathroom, and the separation of dry and wet in the bathroom can effectively solve the problem.

This is due to the fact that the waterproofing is not done well, and it is also related to the air permeability, and there is no good exhaust system, so this situation is caused.

The separation of dry and wet is not done, the air is not circulated, the ventilation is not in time, the waterproof and moisture-proof materials are not used, and the sanitation is not thorough.

If the yellow dirt generated on the surface of the toilet bowl cannot be cleaned with a brush, you can use waste nylon socks to tie it to one end of the brush, and take up some foaming detergent for brushing, and clean it once a month, which can make the toilet as bright as new! Hardware devices have been used for a long time, and may produce some green dirt, but in fact, they are not mildew, but more rust stains. For this problem, it is common to cut half of the lemon, squeeze the lemon juice on the rust stain, soak it for 10 minutes, brush it off with a brush, and finally wash it off with clean water.

What should I do if the bathroom is always moldy? Recently, it has been raining, and the bathroom has been growing mold, which really makes me feel a headache! How can this be addressed and prevented?

Today, Feimojun will share with you some tips for preventing moisture and dealing with mold in the home The bathroom is the most humid and moldy place in the home, and it is quite difficult to keep the bathroom dry and not moldy! But in fact, it can be prevented in this way: the toilet should be ventilated frequently and cleaned frequently.

The dregs of brewed coffee can be placed in the toilet or refrigerator to remove odors, and charcoal can absorb moisture.

There is a problem with waterproofing. If the bathroom waterproofing is not done well, it will lead to a large amount of water vapor in the air infiltrating into the wall, the whole space will be extraordinarily damp, and there will be mold for a long time. Broken water pipes.

Nowadays, the general water pipes are hidden pipes, and if the water pipes are broken, they cannot be found in time, and the water will slowly enter the wall and soak the wall, affecting the entire bathroom. In the case of a broken water pipe, it is treated in the same way as waterproofing.

For the bathroom with a reasonable layout, it is best to have dry and wet separation. Wet areas are not suitable for storage, even in dry areas, toilet paper, towels, bath towels, etc., if they are placed for a long time, they must be stored in moisture-proof storage boxes to avoid moisture. If the mold is not very serious, just tear off the wallpaper, and remove the moldy putty on the wallpaper, then brush the waterproof emulsion, and then re-batch the putty, brush the base film; Glue the inside of the bathroom to close all the joints between the tiles to prevent moisture from penetrating into the walls.

It may be because the ventilation effect of the bathroom is not good, so it will cause the bathroom to be damp and moldy, and you can usually put some desiccant or activated carbon in the bathroom.

Because the windows are not opened for ventilation, and the water is not cleaned up when the bathroom is usually cleaned, this will make the bathroom damp and moldy.

It is generally caused by the fact that the door of the bathroom is usually closed, and the humid air inside cannot be discharged.

It is caused by poor air circulation, and the toilet must be ventilated in time after use.

1. To remove mildew, first wet the moldy wall or floor with water, then sprinkle laundry detergent or toilet cleaning liquid, wait for 5-10 minutes, and then mop it repeatedly with a mop.

2. However, it is inevitable that there are corners or crevices that are difficult to clean, or mildew is difficult to remove at one time for too long.

3. To prevent such problems, first of all, you should check the shower head and water pipe to ensure that there is no leakage or dripping, and secondly, you should open the doors and windows or exhaust fans to ensure that the bathroom is ventilated. Finally, it is necessary to clean frequently to prevent accumulation over a long period of time.

During the spring rainy season, many people's rooms will be damp and moldy, so what should we do? Let's talk about a few solutions: 1. You can use desiccant and activated carbon to prevent moisture and absorb moisture.

There are many desiccants in supermarkets that are specially used for moisture-proof and dehumidification, and the most common are two types: moisture absorption boxes and dehumidification bags. 2. Use a small cloth bag to fill an appropriate amount of lime, tie it into a small bag and place it in all corners of the room, the lime itself has the effect of moisture absorption, and can also slow down the indoor dampness, at the same time, the lime also has the effect of disinfection, killing two birds with one stone. 3. Buy an air dehydrating breather, it is like a vacuum cleaner, it can concentrate the wet air together, and when the moisture is wet, it will turn into water many times.

4. Use air conditioning to dehumidify. Air conditioners used in the home generally have the function of dehumidification, but the way of adjusting the humidity of the indoor air is slower, generally takes two or three hours, and it will make the people in the room feel cold. 5. When the indoor humidity is too heavy, if you do not use the computer or TV, it is best to make a protective cover to prevent the rear of the electrical appliance from contacting the moist air.

And these appliances should be turned on more often, because the heat generated when the machine is running can also effectively dissipate moisture. 6. When the outside moisture is heavy, the doors and windows should be closed to prevent moisture and moisture. In normal times, windows should be opened for ventilation to reduce the indoor water vapor content.

Especially in newly renovated houses, the moisture is particularly high, and it is necessary to ventilate more to remove moisture. The above has introduced so many points, I hope you can use it when the room is damp and moldy in the future, thank you.

Mold is mainly caused by moisture, which is fine, but how to solve it, in fact, it is not very difficult.

Moldy, as long as the mold time is not long, the mold has not completely died and dried to leave a very serious mold, it is very easy to solve, as long as you buy a bottle of mold remover spray a few times, use the strong oxidation effect of the mold remover to oxidize and decompose the mold.

Another word is prevention, which is simpler, is to use anti-mildew spray, spray a few times, so that the wall has the effect of anti-mildew to ensure that there will be no more mildew.

Mainly ensure the ventilation of the bathroom;

Find something that absorbs water;

Waterproofing should be done well, and alkali will appear when water penetrates into the wall;

Open doors and windows to ventilate.

For the mold of the bathroom can be treated with white vinegar, white vinegar not only has the effect of sterilization, but also can take away the stains attached to the surface of the tile, for the mold of the tile gap in the bathroom, you can use a toothbrush dipped in baking soda to clean up, during daily cleaning, spray the multi-functional mold remover on the corner of the bathroom, wipe with a rag, not only can take away the musty smell, but also leave a faint floral fragrance.

1. When the faucet in the bathroom is moldy, mix it with white vinegar and baking soda, soak it completely with toilet paper, wrap the faucet and stand still for half an hour, wipe it with a soft rag, or rinse it with running water.

2. Lemon can also clean the moldy wall well, and can also leave a faint lemon fragrance, squeeze the lemon juice on the moldy place, wait for 10 minutes to brush with a brush, and finally wipe the wall with a soft rag.

3. When there is mildew in the corner of the bathroom, it is necessary to spray it with 84 disinfectant, wait for 5 minutes and rinse it with water, pay attention to the cause of mildew in the moldy location, because of the problem of water storage, and sweep the water with a broom in time after taking a bath.

4. Most of the moldy conditions are caused by dampness, the ground or wall is in a wet state for a long time, pay attention to the dryness of the bathroom, when the mildew spot is serious, you can put the dehumidifier at home in the bathroom, and then take it away after working for an hour.

1. Mold remover + disinfectant. If you don't use glass glue, you may think of using a mold remover at the first time. The cleaning effect of the current mold remover is actually not very good, it only eliminates the mold spots on the surface, and the bacteria are still hidden in the places you can't see, so you also need the help of disinfectant to clean the moldy area.

2. Adhesive strips. If you find cleaning too cumbersome and don't want to buy mold removers and disinfectants, here's another very portable way to get rid of mold spots from the roots, and that is to apply a layer of adhesive strips. The adhesive strip has a strong seal, and sticking it to the mold-prone area can isolate the moisture in the air, so it will not become moldy.

3. Edible vinegar. Vinegar is a must-have condiment in the kitchen, and you may not expect that vinegar can be used to remove mold in addition to cooking and seasoning! The acetic acid in the vinegar can corrode away the mold spots, so as to achieve the effect of mold removal.

And this method is also very simple, you only need to fill a small amount of vinegar in a spray bottle and spray it on the moldy spot.