Newman Jingyin King NO3 how to adjust the volume 5

Didn't my no3 also break Enci, and it was repaired again and again, and finally it collapsed.

If it's the same with other computers, that's Newman's problem. Turn on and off repeatedly, and then there is a string of English.

Otherwise, I knew I had been in this situation. I mean illegal formatting, which is to turn on, turn off and back on. Until a string of English appeared.

It's good if you don't qualify.

Newman's stuff is really not very good, it always goes wrong, I have you no3, it broke for a month, I got a new one, and then I fell down, and it went on strike.

Formatting, which is a system issue with the machine. Everything is back to normal after formatting.

It's not slow, if you want to adjust the sound effect, it's very simple, that is, you first go to the settings and there is a sound quality adjustment, find the one that shows EQ, and then adjust the high and low tones separately.

Generally, you can only adjust the volume.,If you adjust the sound effect, it should have been set in the factory settings.。

If you have to adjust the sound effect of the performance, go to his settings, and then click on the sound effect, and then you can adjust it.

How to adjust the sound effect, you can adjust it directly to this speaker, you can adjust it, you can adjust it.

20hz--60hz

This section of the ascension can give a strong feeling and give people a very loud feeling, such as thunder. It is a strong and powerful feeling in **, if the volume of this frequency band is too small, the feeling of abundance and surging must not be there; In addition, it will lead to the prominence of mid and high frequencies, which will make the sound lose its balance and make it difficult to listen to for a long time. If the boost is too high, it will be cloudy and cause poor clarity, especially in audio equipment with poor low-frequency response and heavy low-frequency.

60hz--250hz

This section is the low-frequency structure of **, and they contain the basic notes of the rhythmic part, including the fundamental tone and the main tone of the rhythmic tone. Its ratio to the high midrange constitutes the balanced character of the timbre structure. Elevating this segment will make the sound fuller, and over-boosting it will make a rumbling sound.

Attenuating these two segments makes the sound thin.

250hz--2khz

This section contains the low-frequency harmonics of most instruments, and if you boost it too much, it will sound like the sound in **. If you raise 600hz and 1khz too much, it will sound like the sound of a horn. If you raise 3kHz too much, it will mask the recognition sound of speech, i.e., slurred speech, and make it difficult to distinguish the labial "mbv".

If you raise 1kHz and 3kHz too much, it will give the sound a metallic look. Since the human ear is sensitive to this frequency band, it usually does not adjust this segment, and raising this segment too much can cause auditory fatigue.

2khz--4khz

This frequency is in the midrange, and if it is raised too high, it will mask the recognition of speech, especially if the 3kHz is raised too high, which can cause listening fatigue.

4khz--5khz

This is the frequency band with a sense of presence, which affects the clarity of sounds such as speech and musical instruments. Increasing this frequency band makes the sound source appear slightly closer to the listener; A 5kHz attenuation will make the sound feel more distant; If you raise 6dB at around 5kHz, you will increase the sound power of the entire mix by 3dB.

6khz--16khz

This frequency band controls the brightness, macro brightness and clarity of the tone. Generally speaking, raising these segments makes the sound loud, but not clear, and is unlikely to cause excessive tooth sounds, and the sound becomes clear when attenuated, but the sound is not loud.

When adjusting the equalizer, it is best to combine the isophonic curve with the frequency response curve of the headphones. For example, if the frequency response curve of the headphones is ideal, i.e., a straight line, then the equalizer can be adjusted to a graph of the isophonic curve similar to the corresponding sound pressure level, so that the loudness of the sound heard in each frequency band is basically balanced; In fact, there is no pair of earphones The frequency response curve of the earbuds is ideally straight, and it is also affected by the different wearing conditions of each person's ears, so it takes a while to adjust the equalizer to grasp the respective sound characteristics of the ** machine and the earphones in your ears.

This requires a firmware upgrade to solve it, you go to Newman's official website to see that there is a special one, in addition to this problem, other can still pull.

If the contact is not good, your MP4 cable may be broken, maybe it is touching some position that causes it to shut down automatically.

The Newman brand is not bad, can you confirm that you are buying the real thing? It's definitely not a garbage brand, do you know that it's a product there?

It is made in Beijing, please do not insult the brand of the Chinese OK, thank you!

Newman's problems are normal, garbage brand.

Find customer service or see if the format is wrong.

Top 1Click Start - Control Panel, 2Tap Voice, Voice, and Audio Settings 3Click Audio Configuration 4The lower right corner is to adjust the sound mode, and you can choose a pop**. There is an adjustment of the sound environment above, choose no trial, it should be OK; Finish.

Either you just get the key on the outside of the phone, and if the button is broken, you can get it in the phone settings.

The buttons on the outside of the phone can be adjusted.

Press the two keys above the on/off key.

The volume button on the outside of the phone.

The first and second shuttlecocks on the other side.

1. Open your phone, find the "Settings" option in your phone, click to enter the "Settings" option 2, enter the "Settings" option on your phone, find "Scenario Mode", click to enter "Scenario Mode" 3, enter "Scenario Mode", find the "Standard Mode" option, and click to enter the "Standard Mode" option.

4. After entering the "Standard Mode", find the "Volume" option to facilitate the next operation5. After finding the "Volume" setting, adjust the volume as needed, and click Confirm after the setting is completed.

1.First of all, change the mess and slide away from the movie king phone"Settings"；

2.Click on it next"Sound"- The volume of nuclear wax"；

3.Here you can dress up to turn down the volume of various types of phones.

I hope mine can help you a little!

1.It may be caused by the lack of SD card driver, you can use the tablet to put the card first, and install the driver.

2.Then there is the SD card itself that has been corrupted, resulting in the loss of the town state.

3.You can try to change the card.

Looking, seeing, and naming...