How to set bicycle speedometer SIGMA1606L

1. Install the battery in the battery slot on the back of the meter head;

2. Press the right button within 15 seconds to enter the tire circumference setting;

3. The Duke uses 26* tires, set to 2055 - 2060, according to the air pressure is a little different, you can use 2060 first

4. Right-click OK.

This computer will jump around at a speed of 30 per hour, or buy a sigma or something, Duke 600 is good, I ride the 08 version of the Duke.

2.Press and hold the "SET button" on the back of the computer for more than 2 seconds, and the screen displays "SET OPEN" to enter the setup mode.

3.The screen displays "size 2155", where the rim value is set. Press the "big key" once, and the screen will display "unit kmh", that is, the displayed value is "kilometers and hours".

4.Press the "big key" once, and the screen will display "dist 0", which is the total mileage. Press the "big key" once, and the screen will display "time 00:02", which is the time.

5.Press the "Big Key" once, and the screen will display "Scan Off", that is, the scrolling display mode is off.

6.Then go back to the "time" interface, press the "set button" once, the numbers will flash separately, and press the "big key" to set the numbers respectively.

7.After the time is adjusted, press the "SET button" again, the screen will display "SET OK", and the time setting is successful.

8.Press and hold the "SET button" on the back of the computer for more than 2 seconds, the screen will display "SET CLOSE", exit the setting mode, and then you can press the "big key" to switch to the time and check the set time.

The easiest way: make a mark on the tire, roll it in a straight line on the flat ground, and then measure the length with a tape measure, this can be accurate to within 5mm, what do you think?

According to my 1609 manual, it should be set to 2114

The surface of the tire should be imprinted.

1. First of all, install the base of the computer to determine where you want to install the computer on the bike, and then install it with tools and fix it with glue.

2. Fix the position of the sensor after selecting it, and then install the induction magnet.

3. The induction magnet must be installed on the wire banner of the tire, and it must be facing the position of the sensor, so that the installation of the induction effect is the best.

4. Find a straight road, ride to the car, adjust the valve core of the tire, mark the nearest position of the ground, keep a straight line to ride a lap, and measure the circumference of the wheel, so that the reference value of the measurement is more accurate.

5. When riding, the tire pressure will change, and the average value can be measured repeatedly.

6. For specific settings, you can adjust the computer to the wheel size menu and fill in the preset value.

Each brand of computer has an instruction manual on the Internet, and you can set it according to the manual. According to their wheels is 26 inches or inches and yes or the width of each brand computer has a list, each brand or even each model setting method may be different, there is no manual only one button to grope for the setting, but at least the computer has a variety of wheels of various widths of the parameter table.

Are you talking about Pro? A lot of models have a pro is a strengthened version, you see the parameters on your tires Yes or 26* according to this refer to your computer brand manual settings, your computer is not Merida's, Merida does not come out of this thing, are other brands sent to you by merchants, each brand has different settings and parameters, can not provide setting methods, mine is a Sigma brand of the computer table, the Internet is full of this brand of setting methods.

Normally, the instructions of the computer have the corresponding tire circumference can be consulted, such as 26* and the like, and there is a number after it, 2155 and other four-digit numbers, the unit is millimeters. This method is inaccurate and there are errors. The easiest and most accurate way to do this is to place it in place with a tape measure, and the wheel will roll around the tape measure to get the actual circumference of the wheel!

Yours and mine are the same code! Press the left and right buttons at the same time, hold down, and after a while an interface will come out, and you can set that value to 2100 and it's OK! Hope it helps!

In general, 2200 is fine. The error is not large

2.Press and hold the "SET button" on the back of the computer for more than 2 seconds, and the screen displays "SET OPEN" to enter the setup mode.

3.The screen displays "size 2155", where the rim value is set. Press the "big key" once, and the screen will display "unit kmh", that is, the displayed value is "kilometers and hours".

4.Press the "big key" once, and the screen will display "dist 0", which is the total mileage. Press the "big key" once, and the screen will display "time 00:02", which is the time.

5.Press the "Big Key" once, and the screen will display "Scan Off", that is, the scrolling display mode is off.

6.Then go back to the "time" interface, press the "set button" once, the numbers will flash separately, and press the "big key" to set the numbers respectively.

7.After the time is adjusted, press the "SET button" again, the screen will display "SET OK", and the time setting is successful.

8.Press and hold the "SET button" on the back of the computer for more than 2 seconds, the screen will display "SET CLOSE", exit the setting mode, and then you can press the "big key" to switch to the time and check the set time.

This car is obviously giant. ~

Look for a point on the wheel, such as a valve near the ground (facing up), perpendicular to the ground, and marked on the ground. Try to keep the cart in a straight line so that the valve is close to the ground again and perpendicular to the ground, marked. I measure the distance between two marks and can obtain the circumference of the tire approximately.

Or measure the center of the hub to the outer circle of the outer tire to get the radius and find the circumference. Probably, whether it is the error of the quantity or the computer meter, or the factors such as the flattening of the tire when riding, can only be a rough reference.

I don't know the diameter of the wheel, so I can't set it.

I went to the place where I bought the car and looked it up, and I found out soon after. Remember it when you're done!

Sigma's code table Look at the wheel diameter comparison table on the manual yourself, according to the number on the rim, compare the wheel diameter on the code table.

Wheel diameter and tire model need to know the width of the tire.

The key in the lower left corner has been pressed and held for three seconds to enter the settings menu, and my 1609 is set like this.

Speedometer - it should be a computer computer, right? Different brands of computer adjustment methods are also different, you can search on the Internet for the brand and model of the computer you have, usually, you must first set the wheel diameter or circumference, time, etc., the language is generally set to you are more familiar with the line.

I have a click first, and the number table won't be adjusted.

Generally, the induction of bicycle (computer speedometer) tachymeter is installed on the front wheel;

First, measure the distance traveled by the wheel in one circle, and enter this data into it;

If you can't enter it, please select a value close to it.

When the speed meter displays the time, press and hold the left button (gray), and then a beating 24-hour clock will appear, and the right button (white) is the OK key! Then it's time to left-click and right-click to confirm!

You look at the manual, there is a button to set, it's really not good, you don't have a button, you press and hold for 3 seconds, there will be a set to show up, that's it.