Bicycle meter Chinese setting, 26 bicycle computer how to set?

Chinese no, what do you want to set up?

Mine is also 26*, the computer is set to 2050, you can make a mark on the tires and the ground, and then roll around and measure the distance, mine is about 2050

1. Install the battery in the battery slot on the back of the meter head;

2. Press the right button within 15 seconds to enter the tire circumference setting;

3. The Duke uses 26* tires, set to 2055 - 2060, according to the air pressure is a little different, you can use 2060 first

4. Right-click OK.

This computer will jump around at a speed of 30 per hour, or buy a sigma or something, Duke 600 is good, I ride the 08 version of the Duke.

Press the two together to enter the settings page, there is a four-digit setting, adjust to 2114, and the time you set by yourself.

As long as the computer you buy is not the one with temperature display in the Shundong computer 548, it will be fine, and that one has the problem of high-speed random jumping.

The computer speed will jump randomly after 30 per hour, you can try to install the sensor as far as possible to the center of the axle, set you can find ** on the general computer instructions to see, is Chinese, the setting method is the same.

Refer to someone else's instruction manual online.

How to install and set up the bicycle computer has always been the majority of riders to think about, today this article will be the first bicycle computer installation and setting method, teach you how to install the bicycle computer. It is relatively simple, and I hope that the majority of riders can participate in the discussion.

One end of the cable is connected to the sensor, and the other end is the base of the computer. Induction magnet and two rubber bands (the large one is used to fix the sensor, and the small one is fixed to the base, which will be used later), and a few ties will not be described in detail, and the installation steps of the computer will be directly started.

1. Let's start the first step and install the base of the computer.

The first thing to do is to determine whether you want the computer to be installed in or in . The manufacturer is installed by default, if you want to install it anywhere, you don't need to adjust it; If you want to install it, you need to remove the base with a screwdriver and rotate it 90 degrees before installing it.

There is foam glue on the back of the base, and the yellow rubber surface can be glued to the handlebar by tearing off the yellow rubber surface, and then use a rubber band to wrap around the handlebar, stuck in the card slots on both sides of the base, and firmly fix the computer base on the handlebar.

2. Next, install the induction head.

The induction wire winds around the brake line all the way to the point where you need to install the sensor, which can be mounted halfway between the axle and the brake on the front lever.

The installation method is similar to the installation base, after selecting the position of the sensor, press it tightly with your fingers, and then use a large rubber band to circle the car bar, and fasten the rubber band in the card slot of the sensor.

3. Install the induction magnet again.

The induction magnet should be mounted on the wire banner of the tire, so that it can face the position of the sensor. After the soft magnet is put on the steel wire, the iron ferrule in the installation package is stuck in the groove of the magnet from the bottom to the top, and the angle is adjusted so that the magnet can be facing the sensor when the steel spokes pass through the sensor, so that the induction effect is the best.

Now that the computer is installed, the next step is to adjust the circumference of the wheels of the computer so that the data read out is accurate.

Place the computer on the base at an angle of 45 degrees, press it down slightly, and rotate it counterclockwise to fix it.

Then find a straight line on the road, the general cement ground has, people ride to the car, adjust the valve core of the tire to make a mark on the nearest position of the ground, keep a straight line to ride 1 lap, and wait for the valve core to stop when it is closest to the ground, measure the distance that passes is the circumference of the wheel, so that the measurement is more accurate than directly looking at the reference value of the tire on the manual, because when the person rides on it, the tire pressure will change, so that the average value can be taken. For specific settings, you can adjust the computer to the wheel size menu and fill in the preset values.

The parameters of the computer are determined by the circumference of the wheel, and the mark is made to walk around the flat road, and then measure it with a meter ruler.

I'm here to find the lookup parameter setting, because I forgot which key to press, and I didn't expect to see such a stupid question from you. The computer of the bicycle reflects the data differently than the motorcycle one, so it is strange that you can set the same record. What kind of broken motorcycle are you, you can't record the kilometers yet.

The landlord must first determine whether the computer you use is calculated by the diameter of the wheel or the circumference of the wheel, and I have installed it on the car for 3 years, and there is no problem with the speedometer of the car.

This one is a bit more cumbersome here because there are a lot of things involved.

This is a difficult technique!

The sensing head is close to the sensor and can react to the odometer, regardless of the radius. The wheel is only 250 300mm, it seems that it is generally not possible to set this value, but it can also be set in this way, such as the wheel circumference is 300mm, the watch is set to 2100, and the display value is divided by 7 is the actual speed or mileage.

The wheel circumference is calculated according to mm, and the position of the induction head of the road bike 2155 should be combined with the signal entry part, which is generally not more than 5mm

"When the battery is installed in the watch, there will be 4 value jumps, and the initial value is 2060" Aren't there two buttons on the speedometer? You press and hold the left button to start the setup.。。 If you don't understand, you can go to the mountain bike shop or ask a rider, they usually will!

Speedometer - it should be a computer computer, right? Different brands of computer adjustment methods are also different, you can search on the Internet for the brand and model of the computer you have, usually, you must first set the wheel diameter or circumference, time, etc., the language is generally set to you are more familiar with the line.

I have a click first, and the number table won't be adjusted.

In power-saving mode, press and hold the right button to adjust the time, press the left button to change the hour, minute and second, and press the right button to adjust.

You can try to press and hold a certain key on the odometer, you can try it out.

How to adjust the time of the mountain bike odometer to 0 if you accidentally put it.

220 10 1 21.

Since there is no starting point and no end point, it should be subtracted by 1 There are a total of 21 service stations.

Mounted on the front wheels, the main thing is to find the right clearance. The sensing head is mounted on the fork next to the macro, and the magnet is mounted on the steel wire, ensuring that each turn of the magnet and the sensing head can be sensing, the number changes, and if you want to calculate the speed mileage correctly, you also need to set your wheel ruler fluid size and circumference.

I've got you a picture of the burial shed.