Common faults of dust collector and treatment methods

Common faults and handling methods of dust collectors include:

Insufficient suction: It may be because the filter or nozzle is clogged and you need to clean the filter or replace it with a new one, or you can check if the motor is working properly.

Filter blockage: The filter needs to be cleaned, which can be cleaned by rinsing with water or spraying compressed air.

Power failure: Check whether the power cord is plugged in, whether the socket has power, and you can also check whether the motor is running normally.

Excessive noise: It may be because the machine parts are loose and need to be re-secured.

Motor failure: If you need to replace the motor, you can contact the after-sales service or replace it yourself.

Weakened suction power: It may be because the tip is worn out and needs to be replaced with a new one.

Air leakage: You can check whether the seal is in good condition and replace it if necessary.

Faulty cable: If the cable is damaged, a new cable will need to be replaced.

The above are some common dust collector failures and how to deal with them, but there are other possible faults. For complex problems, professional maintenance personnel should be required to repair them.

Excessive dust accumulation in the dust bag of the dust collector causes the filter hole to be blocked, so that the airflow is not smooth, resulting in the bag collector.

The suction power decreases or even disappears completely. Solution: Clean up the garbage in the dust bag.

The air duct of the dust collector is blocked. For example, the hose, the suction head or the suction inlet is blocked by garbage such as paper balls and cotton wool, which will also make the vacuum cleaner.

The suction power decreases or disappears completely.

The body of the dust collector may be caused by the air leakage caused by the unsealed accessories. There are the following two situations: the air inlet of the host in the main engine cavity of the bag filter is not properly assembled, or the rubber blocks or rubber rings around the host are not placed; Or the rubber seal is aging and displacement, causing the air flow to flow out from the edge of the tuyere of the main engine, and the wind pressure.

Minish. Solution: Promise to open the main engine cavity to eliminate the above phenomenon, or replace the rubber block and rubber ring.

Dust collectors.

Common faults of dust collector: 1. Small air volume and insufficient force. Solution: Replace the dust filter bag with a new one.

Second, the emission exceeds the standard. Solution: Reduce the air volume or replace it. New dust filter bags.

The blowback system does not work. Solution: Check whether the compressed air and blowback valves are normal.

If it is a flying elephant dust collector, there are generally three aspects of failure.

1. For power problems, check whether the circuit is short-circuited, damaged, leakage, unstable voltage and current or damaged motor.

Second, whether the bag or filter cartridge has not been cleaned or damaged for a long time.

3. The main body of the equipment is damaged.

Summary. Hello dear! There are the following reasons for the poor dust collection effect:

1. Filter bag material pulse bag filter bag material has a decisive role in dust collection efficiency. Many enterprises with 24-hour uninterrupted production have high requirements for the performance and use of dust collectors. Therefore, the filter bag material should have enough strength to withstand multi-frequency, high-pressure spray cleaning, good air permeability, good filtration effect, long service life, and high cost performance.

What are the reasons for the poor dust collection effect and how to deal with it.

Hello dear! There are the following reasons for the poor dust collection effect: 1. The filter bag material pulse bag filter bag filter has a decisive role in the dust collection efficiency.

Many enterprises with 24-hour uninterrupted production have high requirements for the performance and use of dust collectors. Therefore, the filter bag material should have enough strength to withstand multi-frequency and high-pressure injection cleaning, good air permeability, good bending effect, long service life, and high cost performance.

2. The relationship between the diameter difference between the filter bag and the keel is very important. The sliding gap between the mating is too small, and the expansion and contraction of the filter bag cannot meet the requirements, which will cause poor cleaning effect; When the gap is too large, the filter bag will increase friction with the keel, resulting in the accelerated width of the filter bag to let the cloth wear, generally when the filter bag and the keel are closely matched but leave a certain gap, usually the filter bag is 10mm to 20mm longer than the circumference of the keel, and the length is consistent. In addition, when the keel is broken, deformed or there are burrs in the weld, it will also cause accelerated wear of the filter bag.

In addition, the filter bag should be made of cloth bag with elastic ring, so that the pattern plate and the filter bag are tightly sealed, and the wear of the reverse fold at the top of the filter bag is reduced. When assembling, confirm that the position of the blow pipe and the filter bag is aligned, so as to prevent damage to the filter bag caused by the mechanical friction of the upper section of the filter bag caused by the improper position of the blow pipe.

1) The dust is damp and compacted or sticky, which leads to the blockage of the outer surface of the filter bag, and the resistance of the filter bag increases in addition to the dust toucher, which affects the dust removal efficiency, and generally extends the spray cleaning for 10-20min after the shutdown.

The main reasons for the lack of prudent cleaning of filter bags mainly include excessive frequency of ash cleaning and long ash cleaning time. The number of ash cleaning is too frequent, and it is easy to loosen the fiber structure of the filter bag, thereby increasing the fine dust in the gas to block the filter bag, and the ash cleaning time is too long, and the initial powder layer on the surface of the filter bag will be cleaned off together.

The main reasons are as follows: 1. The air volume is small 2, the pipeline is 3, the dust filter bag is 4, the dust removal range is too large and many other factors.

Generally, it can be solved by increasing the resistance of the new filter bag, so that the resistance of the new filter bag is close to that of the old filter bag.

Generally speaking, poor sealing of the area under the rotor is one of the main causes of dust in the crushing plant. It is proposed to add the remnants of the inclined baffle cluster with both diversion and buffering functions at the discharge port.

May you have a light when it's dark, an umbrella when it's raining, someone to accompany you on the road, and if there are no other problems, I wish you a happy life!

In other words, you can choose a suitable dust bag to solve the problem.

In addition, the fabric and design of high-temperature dust-resistant bags should pursue high-efficiency filtration, easy dust peeling and durable effect as much as possible.

What are the reasons for the poor dust collection effect and how to deal with it.

There may be several reasons for poor dust collection:1Excessive air backflow.

2.The filter element is not fine enough. Judge the skin stupid 3

The air velocity is too slow. 4.Dust outbreaks are frequent.

To deal with these causes, check for over-controlled air backflow, replace finer filters, speed up the air, and take steps to control the frequency of dust outbreaks.

Summary. There are five main reasons why the vacuum cleaner does not work: 1. The vacuum hose is blocked; 2. The dust bag is full; 3. The filter bag is blocked; 4. The bristles of the rotating brush are worn; 5. The fan blades are not fixed.

There are five main reasons why the vacuum cleaner does not work: 1. The vacuum cleaner is blocked; 2. The dust bag is full; 3. The filter bag is blocked; 4. The bristles of the rotating brush are worn; 5. The fan blades are not fixed.

1. Blocked vacuum hose It is necessary to know that the vacuum cleaner sends dust to the dust bag through the hose, so during the work of the vacuum cleaner, it is inevitable that it will vacuum some things that are easy to clog, such as larger hard substances and strip-shaped objects. If so, we should disassemble the vacuum cleaner, shake off the dust inside the hose, and clean up their blockages in time. 2. If the vacuum cleaner is used for a long time, the garbage will reach the upper limit if it is not cleaned up in time, and the vacuum cleaner will not work.

3. The dust filter bag is blocked Generally, the vacuum cleaner has been used for a long time, and the dust filter bag will be covered with dust, and the dust filter bag will be clogged slowly. At this time, you only need to shake off the dust from the dust bag. 4. The bristles of the rotating brush are worn out Although the motor of the vacuum cleaner rotates, the rotating brush cannot be dusted, so the suction power is very weak.

If so, disassemble the brush, adjust the position of the brush assembly, so that the bristles of the brush are close to the ground, and the rotation can fully dust, if the wear is serious, the brush can be replaced with a new one. Changyu 5. The fan blades are not fixed properly When the fan blades slide on the motor, it will also affect the dust collection effect. If this happens, you should tighten the positioning screws of the fan blade, and if you can't solve it yourself, you should go to a professional maintenance personnel for repair.

Dust collection in industrial dust collectors can be caused by a variety of issues, some of which may include: Clogged filters: If the filters in the dust collector are clogged with dust, they will not be able to capture dust effectively.

Airflow Restrictions: If airflow is restricted, such as blocked pipes or ducts, the dust collector will not be able to effectively remove dust. Leaks:

If there is a leak in the dust collector, the dust may leak and cannot be captured. Motor issues: If the motor powering the dust collector fails, it may not be able to generate enough airflow to capture dust effectively.

Electrical issues: If the dust collector has an electrical problem, such as a circuit breaker trip or a faulty circuit, the dust collector may not function properly. Improper maintenance:

If the dust collector is not properly maintained, it may not be able to capture dust effectively. Inadequate design: If a dust collector is not designed to handle the specific dust it collects, it may not capture effectively.

Overload: If the dust collector is overloaded, it may not be able to capture dust effectively. It is important to note that the problem of discontinuous dust collection can be caused by one or more of the above problems.

It is best to consult the dust collector manual or contact the manufacturer for specific troubleshooting steps.

Hello dear <>

Happy, I'm glad to answer for you According to your question, what happens to the discontinuous dust collection of the industrial dust collector, whether the air intake channel is blocked, and third, whether the filter screen for dust collection and the filter screen of the motor should be cleaned up, and the dust sells more slowly, and the filter screen is full of dust, so it has to be cleaned. Hello and kiss I hope this service can help you <>

<> you can click on my avatar to follow me and give me a like, and if you have any questions in the future, you can consult me again, and look forward to serving you again. Wishing you well; Have a good life and all the best! If you are satisfied with my service, please give a thumbs up<>

Once again, I wish you all the best! Peace and joy.

There are several reasons why an industrial dust collector does not collect dust continuously:

Clogged filter: If the filter of the dust collector is clogged with dust and debris, it will block the flow of air and dust, resulting in discontinuous dust collection by the dust collector. The solution is to clean or replace the filter.

Fan failure: If the dust collector's fan fails, such as a muffled motor or stall, it can cause the dust collector to collect dust discontinuously. The solution is to repair or replace the fan.

Dust collector air leakage: If the dust collector is not tightly sealed, air and dust will leak out of the dust collector, resulting in discontinuous dust collection. The solution is to check and fix the sealing problem.

Altered airflow: If the airflow of the collector changes, for example due to increased or altered ductwork resistance, it may result in discontinuous dust collection in the collector. The solution is to adjust the piping system lease to accommodate changes in airflow.

If none of the above methods work, you need to ask a professional dust collector maintenance personnel to check and repair.

Determine whether the dust collector is working properly. First of all, it depends on whether the suction power of the dust collector is running normally, and secondly, secondly. It is necessary to see if the ash cleaning system is normal.

Again. It depends on whether the ash discharge system is normal.

Finally, look at the overall dust removal system. Whether the operation is abnormal.