How to adjust the distance of Malibu high beam if the distance is not far enough

1. If you adjust it yourself, it is best to adjust it at night, but don't adjust it on the road, not to mention the danger, it is not easy to see the effect, try to choose it in the community or yard.

2. It is best to prepare a flashlight, which is not very clear at night.

Adjustment essentials: 1. Put the front of the car vertically against the wall, about 10 meters away from the wall.

2. Turn on the high beam tone, generally the high beam is suitable, the low beam is also suitable, it is best not to turn on the low beam tone, it is not easy to distinguish whether the high beam is suitable.

3. Cover the temporarily out of tune lamps with a cloth and tune them one by one.

Here are the steps:

1. After turning on the high beam, stand in front of the headlight, keep your feet as close to the headlights as vertically as possible, observe the position of the high beam on your feet, take the center of light (that is, the brightest light emitted by the headlights) as the center point, and write it down.

2. Then go to the wall, move vertically to the wall (don't go crooked), and mark the wall according to the position of the light center on the foot.

3. Use the screws to the scale teeth of the rotating headlight, and be sure to shine the light center on the engraved mark (the distance between the top and bottom should not exceed 10 cm).

4. If there is no other person in the car when the lights are adjusted, you can adjust the optical center slightly higher (generally not more than 5 cm), the reason is very simple, the empty car should be higher, and the car should sink a little bit.

5. Adjust up and down to find that the center of light moves obviously, if you adjust the left and right, the center of light is not obvious, I turned several times before moving a little, so don't worry if you see that the center of light is not moving left and right, continue to turn the screwdriver hard until the center of light shines on the mark you engraved.

6. After the center of light of the two lights is aligned with the scale, stand in front of the front of the car (slightly away from the car), pay attention to the lamppost emitted by the headlights, and it is easy to see the high beam at night to see if it is vertical forward, because it is possible that you have shifted when you walk to the wall to make a mark.

Supplement: 1. If you don't change the headlights, you generally only need to adjust the height, and the left and right are basically more accurate.

2. Adjust the headlights, please note that the left light (seen from the driver's seat) should be slightly lower than the right light, otherwise it will shine on other cars when driving, which will affect safety.

If you sit too much or have more goods, the light will not be far enough, according to the figure below, stop the car at night and try which gear is suitable (no need to explain it, just be comfortable).

1. Find Malibu's ignition stalk switch, step on the brake, and ignite the vehicle to start the vehicle.

2. Turn on the light switch on the left side and adjust the knob to the auto mode, which is the automatic headlight mode.

3. The button pointed at by the arrow is the headlight height adjustment button, which rotates upwards and the light irradiation height downward; Rotate downwards and the light shines upwards. Sitting in the driver's seat and watching the lights while rotating the button, you can see the obvious changes, and the operation is simple.

4. Malibu headlight height adjustment is divided into 0123, a total of 4 levels. Select 0 if there is only one driver in the car, 1 if there is a driver and one other person in the car, and so on, which keeps the vehicle's headlights in the optimal range.

5. Next to the headlight height adjustment switch is the brightness adjustment of the central control light of the instrument lamp, and the corresponding instrument light and the brightness of the central control have obvious changes in light and darkness when adjusting.

Malibu lights are not close and far as one, they are separated. The combination of far and near means that the high beam and low beam are on the same bulb, and there are two filaments inside the bulb, which can be switched at any time. The bulb that can only produce one beam of light in a single bulb is usually called a single lamp, and the double lamp is divided into a near and far (bixenon lamp) and a telescopic lamp, which refers to a bulb that can produce two different beams of light in a single bulb.

The working principle of the integrated lamp is: the light emitted by a group of beams is reflected by the lampshade mirror and shoots straight forward, which is commonly known as high beam; The other group is the polarized beam, the light emitted to the visor blocks the upper part of the lampshade reflector, and the reflected light is diffused downward to the ground, which will not cause dazzle to the driver of the opposite car, this light source is commonly known as low beam.

The high beam and low beam of the headlights of the car are through two light sources with different resistance in different positions, the positions are different, the focal length is not the same, and there are obstructions under the low beam light source, and only half of the light source is reflected in the low beam.

The lighting effect of headlights is mainly related to two factors: luminosity and angle. The car will have bumps and vibrations during driving, so the lights will be loose and misaligned, which is also the most common reason for the decline of lighting effect.

The angle of the headlights is adjustable, most of them are in the front cabin, behind the headlights, and are adjusted by positioning screws, and some are adjusted outside the car, or electrically adjusted in the car. Without the aid of a metering device, you can park the car on a straight road and start the engine, but remember that the generator must be used to generate electricity to keep the headlights working properly, and after each fine-tuning angle, switch between low beam and high beam until it feels good.

Photo by Li Xiongwei) @2019

The Chevrolet Malibu exterior light control is located on the instrument cluster on the left side of the steering column, and there is also a light switch lever on the left side of the steering wheel. Let's take a look at how to adjust the height of Malibu headlights.

Malibu is equipped with a manual headlight height adjustment control device, the finger wheel is located on the exterior light control device, which is divided into 0, 1, 2 and 3 gears, 0 gear means the front seat is occupied, 1st gear means all seats are occupied, 2nd gear means all seats are occupied, the luggage compartment is cleared with items, and 3rd gear means that the driver's seat is occupied and the luggage compartment has items. With this function, the headlights can be adjusted to a height that matches the vehicle's load. Properly adjusting the headlight height can reduce glare caused by other drivers.

To adjust the height of the positive headlamp, the low beam headlamp must be turned on. Turn your head clockwise or counterclockwise and muffle the thumbwheel to adjust the headlamp height.

Automatic headlight height adjustment, which automatically adjusts the headlight tilt according to the vehicle load. For vehicles equipped with a smart high beam system, the system can turn the vehicle's high beams on or off depending on the surrounding traffic. When it is dark and there are no other vehicles, the system turns on the high beams.

Summary. Pro-<>

We'll be happy to answer your questions. Generally, the high beam bubble of the Malibu left headlight fails. First of all, please check whether the high beam bubble of the Malibu left headlight is depleted, if so, you can replace it with a new high beam bubble; If not, you can check whether there is a problem with the high beam driver or circuit of the Malibu left headlight, and if so, you need to replace the driver with a new one or repair the circuit.

Malibu left headlight high beam is not right high beam what's going on.

Dear <> will be happy to answer for you. Generally, the high beam bubble of Malibu Zuo Da Sowei lamp has failed. First of all, please check that the high beam bubble of the Malibu left headlight is seeping and has not been exhausted, if so, you can replace it with a new high beam bubble; If not, you can check whether there is a problem with the high beam driver or circuit of the Malibu left headlight, and if so, you need to replace it with a new driver or repair the circuit.

In addition, it is generally a problem with the low beam and high beam switch of the right headlight, which needs to be checked and replaced.

The left high beam is not bright, the right high beam is bright, and the bulb has been replaced but it does not.

It is usually a circuit fault. Please check the vehicle circuit to see if there is any short-circuiting, poor contact, etc. Generally, it is necessary to inspect the bulb early to see if there is any damage or poor contact.

If there is no problem, it is generally necessary to replace the high beam controller or adjust the circuit connection to ensure that the circuit is running properly. <>

The height adjustment of the headlights is adjusted by using the wheel-shaped adjustment knob on the left side of the steering wheel, with the lowest gear at 0 and the highest at 3.

In terms of appearance, the 2018 Malibu is basically the same as the current model, with a family-oriented front design that incorporates headlights and an upper grille. In addition, the entire system has changed to a new nomenclature, and the rear of the new car will be marked with a new "530T" logo to identify it. Malibu adopts Chevrolet's new family-style front face design, with a U-shaped large mouth design combined with a honeycomb front grille, and the headlight design is somewhat similar to the current style of the Gijingk HIDEOGT.

The overall design gives people an atmospheric, calm feeling. The rear taillights are designed with LEDs. The rear of the car is inspired by the design of the Bumblebee, with square taillights and chunky twin exhaust pipes showing a strong sense of American power.

The new 2018 Malibu 530T Fashion Edition adds a number of practical and technological configurations to improve comfort on the basis of the current 530T Comfort Edition, including a multi-functional leather steering wheel, perforated leather seats (8-way electric adjustment of the driver's seat), keyless entry with one-button start, cruise control, electronic parking, rear exhaust air vents, etc. to further improve the cost performance.

Millions of car purchase subsidies.