Do I need a professional to refill the printer?

1. First turn on the power of the printer, then open the printer lid so that the printer cartridge accumulates to the left, and then remove the ink cartridge that needs to be added

2. Take out the ink cartridge, feel the recess under the ink cartridge with your hand, disassemble the upper film, and the ink injection hole is under the film. The black cartridge has only one hole, and the color cartridge has three holes, which are red on the top and blue on the left.

Right yellow. <>

3. After tearing the film, find the ink injection hole, and use nails and tweezers.

and other workers pulling the ball out of it. After removing, it is ink to fill the holes, and the next step is to add ink.

4. Prepare some paper towels and put on the gloves that came with the ink, and then you can refill the cartridge. When refilling ink, use a syringe.

or other tools to draw the appropriate amount of ink, and then add ink through the ink filling hole. When slightly tilted, it is easier to fill the ink. The ink must be added slowly so that the sponge can absorb the ink. If it is urgent, it will cause the ink to spill.

5. After adding ink, put the beads back into the hole, and then paste the ***, and the ink work is completed. When attaching the label back, be careful not to cover the vent, otherwise the ink will not be able to circulate and not be able to print normally.

When adding ink, you need to open the upper cover of the ink cartridge and find the ink filling hole, there are usually two, one of which is for air intake, and you can add any small hole to it. The purchased ink needle is then used to inject ink into the small hole. Then close the lid and dip it firmly with 502 glue.

There are points for the model of your machine.

There are certain differences.

See for yourself first.

In the whoosh search.

Roewe continuous ink supply.

How to add water to the cartridge.

We have professional videos and tutorials.

1. First of all, the first step is to use the ink sink window to visually check the ink level of the printer.

2. The next step is to open the cartridge lid.

3. Then it is necessary to take the plug on the cartridge that is being filled under the Mori Dynasty. Note that at this time the stopper should be placed upside down on a piece of waste paper.

4. Then you should press and hold the nozzle on the ink cartridge, gently push it down, and then let the ink flow into the ink cartridge. Fill the cartridge to just below the lowest fill line on the cartridge.

5. Finally, after filling the ink cartridge, pull up the ink bottle vertically. Hold the cartridge upright, then push the cartridge plug into the slot on the cartridge and close the cartridge lid.

The specific steps to add TravelWise ink to your printer may vary depending on the type of printer and cartridge structure, but here are some common methods for reference:

Remove the cartridge. The cartridges on most printers can be easily removed with buttons, handles, or levers on the top or side of the printer. Be sure to follow the operating instructions for that particular model to avoid damage or accidental spills.

Fill the cartridge with ink. In general, you will need to pour ink into a small hole above the cartridge, usually with a corresponding label indicating a different color filler. Before filling, read the owner's manual carefully for the recommended ink volume and ink type, and make sure to use the appropriate ink for your printer's make and model.

Pay attention to the amount of ink. Never add too much ink when adding it, as this may cause the print head to clog or flow too much, which can then cause quality issues. At the same time, don't wait until all the ink is used up before adding ink to avoid additional line loss and waste.

Reinstall the cartridge. After proper refilling, slowly insert the cartridge back into place and make sure it is securely seated on the retainer.

Laser printer.

There is no need to use ink, the laser beam emitted from the laser source.

After being modulated by an acousto-optic deflector controlled by a character lattice information, it enters the optical system and rotates the drum through a multi-faceted prism.

Perform lateral scanning;

Therefore, an electrostatic latent image of the character or image is formed on the light guide film layer on the photoreceptor drum, and then the desired character or image is obtained on the paper after development, transfer and fixing. The main advantage is the high printing speed, which can reach more than 20,000 lines.

The printing quality is high, the noise is low, ordinary paper can be used, and characters, graphics and images can be printed. Due to the high print speed, it looks like one page at a time.

The printer needs to replace the ink cartridge to add ink, and the operation method is as follows:

Device: HP Printer M1005

1. After confirming that the printer has no powder, you need to take out the toner cartridge of the printer.

2. After taking out the toner cartridge, take the toner cartridge out of the drum cartridge and press and hold the green button on the left side to separate it.

3. Take out the newly bought powder cartridge from the package and shake it horizontally from side to side several times, mainly to shake the powder inside.

4. Then remove the yellow plastic cover in front of the new compact, 5. Put the new compact into the original drum box, and press it gently until the green card on the left side is stuck.

6. Install the installed toner cartridge into the printer as a whole, and the installation method is just the opposite of the method of taking it out.

7. After installation, close the front cover, then turn on the power of the printer for system testing, after the detection is successfully completed, the green light of the printer [ready] will light up. The installation is complete and ready to use.

Use a syringe to fill the cartridge with the following methods:

1. Material tools.

Inks, cartridges, syringes, ink absorbers.

2. Methodology. 1. Open the lid of the printer and take out the ink cartridge.

2. Confirm the injection point.

3. The syringe draws the ink from the ink bottle.

4. Slowly inject ink from the injection hole

5. Use an ink suction device to suck out a little ink

6. Put the cartridge back into the printer and add it.

Notes:1. Before adding new toner to the printer toner cartridge, be sure to pour out all the waste toner ink left over from the previous use, otherwise, if you add new toner and ink, the printed paper will be very blurry.

2. Add new ink to the toner cartridge, be sure to put the toner cartridge vertically, and then slowly add it inside.

Remove the label from the color cartridge of your HP printer.

After the label is removed, drill holes for the cartridge.

After drilling the hole, use a syringe to refill the cartridge with ink.

Be careful not to add the wrong ink: the colored one has three holes, the top one is red, the left one is blue, and the right one is yellow; The black one is a black ink hole: add 4ml to each of the colored ones, and add 8ml to the black ones.

Pay attention when adding: put the needle tube a little obliquely, gently, slowly, if you add too fast, it will flow out of the nozzle below.

Finish the diagram after loading it directly:

The printer in the factory is out of ink, so it's easy to add ink to the cartridge.

The printer in the factory is out of ink, so it's easy to add ink to the cartridge.

1. First turn on the power of the printer, then open the printer lid so that the printer cartridge accumulates to the left, and then remove the ink cartridge that needs to be added

2. Take out the ink cartridge, feel the recess of the ink cartridge with your hand and find that the silver is not closed, disassemble the upper film, and the ink injection hole is under the film. The black cartridge has only one hole, and the color cartridge has three holes, which are red, left, blue, and yellow.

3. After tearing off the residual film, find the small hole of ink injection, pull out the beads with nails, tweezers and other tools, and add ink to the hole after opening the dry banquet, and add ink in the next step.

4. Prepare some paper towels, bring gloves sent with ink, you can add ink to the cartridge, use a syringe and other tools to absorb the appropriate amount of ink through the ink injection hole, slightly inclined to inject ink. The ink should be added slowly to facilitate sponge absorption, and if it is rushed, the ink will overflow.

5. After adding ink, put the beads back into the hole, and then paste the ***, and the ink work is completed. When attaching the label back, be careful not to cover the vent, otherwise the ink will not be able to circulate and print normally.