How to change the zipper of the clothes, and how to put the zipper back when the zipper of the cloth

1. First remove the old zipper, which can cut the needle and thread intermittently, and then slowly remove it.

2. Prepare a new zipper, preferably just the right length, at least not too short, because it is easy to do if it is long, and it will be troublesome if it is short.

3. First use the green thread to fix the new zipper on the padded jacket by simply sewing a few stitches.

4. Start sewing from the bottom left side of the padded jacket, and the stitches are best to be fine.

5. When sewing to the top, cut off the zipper part that grows out obliquely, and then slowly stuff it into the gap of the padded jacket.

6. The right side is also slowly sewn up like this. The right side can't be fixed, so it's a bit complicated to sew.

7. Also cut off the growing part and sew it into the crack.

8. Use scissors to remove the pins and threads used for fixing, and arrange the padded jacket.

Tools: scissors, thread, needle, new zipper.

1. First cut off the old zipper or broken zipper on the clothes from bottom to top with scissors, and you need to cut it neatly.

2. Then prepare the materials for scissors, thread, needle, and new zipper.

3. Then thread the needle, reverse the clothes to the inside, and start sewing the new zipper from the bottom to the top.

4. Then you can see that when sewing, it needs to be tightly connected with a needle and a thread.

5. Then sew until the previous step, and if you can see that there is an excess, you can cut it with scissors.

6. Then after it is done, it is to tidy up the clothes, so that it is done.

How to change the zipper:

Buy a zipper of the same length on the garment, then remove the broken one and sew a new one on.

You can also take your clothes to a tailor shop that specializes in changing zippers, or a specialist repair shop for shoe repair and zippers.

If the zipper lock is broken, you have to replace it with a zipper lock. If it doesn't break, follow these steps:

First, pull off the top tooth of the zipper with pliers, and both sides should be dialed; Then pull the zipper lock to the top, then merge the teeth on both sides, and then put the zipper lock in, and put the big teeth on, and that's it.

When the zipper of the garment is not opened and closed smoothly, if the chain head is pulled hard, the tooth element bite will malfunction. At this time, paraffin wax or lubricating spray is applied to the surface and inside of the tooth, and then the slider is moved several times before sliding easily.

When opening and closing the zipper, sometimes the chain head bites the line segment or the fabric and the slider cannot be pulled, if you force the slider to pull, it will bite deeper and deeper, and the slider should be reversed on the one hand, and the fabric should be untied on the other hand. When you bite into it completely, do not pull the slider vigorously, but slowly reverse the slider. And when sewing zippers, don't leave hidden dangers.

First of all, let's take a look at the basic composition of the zipper head, which is composed of several important parts such as the pull tab, the pull tab lock, the zipper body and the zipper head lock. The function of the pull tab is to drag the zipper head, the function of the pull tab lock is to combine the pull tab with the zipper body, the important role of the zipper head lock is to prevent the zipper head from sliding due to other external forces in the case of non-artificial dragging, and the function of the zipper body is to interlock the two zippers. When the pull-tab is accidentally damaged, the best solution is to find an old zipper that is unused, remove the pull-tab and attach it to the new zipper.

In fact, the most critical part at this time is the disassembly and assembly method of the pull tab, use a screwdriver or other sharp tools to pry off the pull tab lock of the old zipper, and then you can remove the pull tab lock, the same is true when installing the pull tab, when the pull tab is installed, and then buckle the pull tab lock back to the zipper body in situ. Of course, in the case of emergency, directly use a thin wire to pass through the small hole between the zipper lock and the zipper body, and entangle the two ends of the wire, which can also be used urgently.

Dismantle first, memorize the structure of each position while dismantling, and then sew the new one back on.

Send it to a special place to change the zipper for two dollars.

Take it to the place where it is sewn and change.

Preparation materials Tools: forks, zip clasps, clothes.

1. Place the zipper buckle on top of the fork and place it in the middle of the fork.

2. Fix the zipper buckle in the middle of the fork, and pay attention to the front and back of the fixation.

3. Bring the clothes with the zipper off and insert the zipper buckle into both ends.

4. After putting it on, pull it down, pay attention to the reverse of the clothes here, pull the inner one, and turn the clothes back after pulling.

5. Finally, it was restored.

How to put the zipper back on the clothes, the old tailor will teach you a trick, and you don't have to spend money to find someone to repair it.

Hello dear! How to install the chain head off: First prepare a lighter, use the lighter to burn the cloth surface of the fallen off end to prevent it from falling off, and place the zipper on the table with the level facing up.

Pull the zipper head into the teeth with the teeth facing up, and pull both ends of the cloth belt together and pull it outward.

The zipper head will go down the tension of the cloth belt to the outside into the teeth, and the slider will be installed after the cloth belt is pulled out, pull out the excess teeth with oblique nose pliers, do not use too much force, so as not to break the cloth strip, install the lower teeth to prevent the zipper from sliding out.

When using it at ordinary times, if the zipper is loose and the teeth are missing, you can use a small hammer to gently knock a few times on the zipper head to make the upper and lower chain teeth bite tighter, and the teeth will not be removed again.

After the clothes are clamped with the zipper, you can use dish soap, candles, and knives to apply loose celery dish soap to the part where the zipper is clipped, and use its lubrication to pull the zipper out, or apply candles to the zipper teeth to reduce friction, and you can also use a knife to pry the clamped zipper open, and then reinstall it on the zipper.

1. Dish soap treatment

After the clothes are zipper clipped, the use of dish soap can be disposed of. Use a cotton swab dipped in dish soap, then apply it to the zipper of your garment, wait for the detergent to flow into the zipper, and then try to pull it to separate the zipper from your garment.

2. Apply candles

Clothes zipper clip clothes, may be the cause of excessive friction of the zipper, you can continue to apply candles to the zipper teeth to reduce friction, and then try to pull the zipper, you can separate it from the clothes.

3. Pry open with a knife

If you don't have candles and dish soap, you can use a knife or a coin to go deep into the bayonet of the zipper, and then force it outward to pry the zipper open, and then the clothes will be separated from the zipper, and then reinstall the zipper on the zipper.

The zipper of the clothes is off, and there are ways to install it:

1. The lighter burns the edge of the cut cloth belt to prevent it from falling off.

2. In the upward direction between the teeth, pull the zipper head into the teeth, and pull both ends of the cloth belt outward; The zipper puller will follow the outward tension of the tape into the teeth.

3. After the cloth belt is pulled out, the slider is installed.

4. Pull out the excess teeth with oblique nose pliers.

5. Install up and down.

Tips for maintaining zippersWhen you use them at ordinary times, you should pay attention to whether there are problems such as "broken belly", "tooth loss" and "crookedness" on the zipper. If the zipper is loose and the teeth are lost, you can use a small hammer to gently knock a few times on the zipper head to make the upper and lower chain teeth bite tighter, and the teeth will not be removed again. Do not overfill all kinds of bags, pockets or wallets with zippers.

When pulling the zipper, you should first align the teeth on both sides closely, and then pinch the zipper puller and gently pull forward along the track, without pulling too hard.

1. Use a lighter to pick up the edge of the zipper pull, so that the next steps will not be taken off.

2. As the front side, the left tooth should be higher than the right tooth. Put the zipper puller up, press down hard, and then pull both sides of the zipper, and the slider will slide down naturally, and it will be installed.

3. Tear off about 4 pairs of teeth with needle-nose pliers, clamp the U-size with needle-nose pliers, install it on the top of the tooth at the very end, and clamp it vigorously, the right side is the same as the left.

4. Next, to install the tail parts, first of all, tear off a few pairs of teeth, install the I-code, that is, install the pull tab on the zipper head, and also install the pull tab into the old buckle on the spicy zipper head, and clamp the open buckle with needle-nose pliers.