The phone screen protector is pasted on whether the blistering is slowly gone

The phone screen protector is blistered and will not be slowly gone.

First, the solutions to the above problems are as follows:

1. If this situation is encountered, first paste the torn surface to the protective layer as much as possible, pause the attachment work, and gently stick out the lint and particles with the adhesive side of the tape (the adhesive tape is more gravitational than the adsorption layer). Then continue to attach, the tape used to remove lint and particles can only be used once, and the next time the tape is needed, it will be torn out of the tape roll again.

2. Be cautious when applying the film to the last edge, as bubbles are most likely to appear. Try not to use cards and wipes to scrape this step, try to press the protective film obliquely with both hands, so that the film is slowly adsorbed, the middle part tries to ensure that there are no bubbles, and the edge part is not in a hurry, and then deal with the bubbles on the edge after the whole film is adsorbed, and then use a small scraper to gently drive the air out.

Second, the reasons for the above problems:

1. Because of the uneven force, the air is not completely excluded, at this time, the middle layer should be lifted to the position with bubbles, and the bubbles can be gently driven out with a cleaning cloth or small scraper.

2. The bubbles are generated because there are residual micro dust particles on the screen, (the middle layer occasionally adsorbs suspended particles in the air). This kind of bubble is not easy to drive out, and it is easy to find that it is caused by lint and particles.

It won't be slowly gone, it will always be. You can follow these steps:

1. Clean up the dust and oil stains on your hands first, and wash them with hand sanitizer first.

2. Wipe the surface of the mobile phone with a glasses cloth or a soft cloth that does not shed a small amount of water, and clean up the dust and fingerprints on the surface.

3. Tear off one side of the protective film, then aim at the phone, align the top and left sides and paste the lower film.

4. When sticking the film, try to maintain a uniform speed, and please pull back less when bubbles appear to ensure that there are no bubbles on the surface of the film. What should I do if there are bubbles on the phone film? Then use a wool felt scraper, or a padded scraper, to avoid scratching.

Slowly press the film little by little on the surface of the phone, in this case, there will be few bubbles instantly.

5. After pasting, repair the bubbles in some areas. Wrap the credit card with a hard card, credit card, etc., with the soft cloth that just wiped the screen, and then slowly exert force to scrape the bubbles out of the edges.

Immobility will always exist. Set off a repost.

It doesn't go away on its own, but it can go away on its own.

Specific steps: 1. Prepare the tools: scissors, scotch tape and a small piece of cloth.

2. This is a mobile phone sticker with bubbles. Use a piece of cloth to push off the air bubbles that can be squeezed out first. Fold the cloth a few times and push the bubbles with its edges.

3. There are also these bubbles that can't be pushed off. Why can't they push it away? Because there is dust in it, it is the dust that forms bubbles in it, and we have to take out the dust and remove the bubbles.

4. Cut a piece of 1 2 inch long scotch tape and stick it to the film next to the foam dust, and then cut a small piece of scotch tape and stick it to your face.

5. Then use your hand to pull up the scotch tape and stick it to the film, pull a slit, as long as you pull the seam, you can make the tape of the other hand, here in order for you to see clearly, put some big, too big and easy to pull in more dust.

6. After pulling it up, you can see if there is dust on the film or on the phone screen. Look closely, the dust is very small, and then glued to the other hand with scotch tape.

7. The dust will stand out, and you see that there are no bubbles.

8. Let's use the same method to get the other dust out.

Q: Why is there a bubble when the mobile phone screen is broken and the tempered film is pastedAnswer: Hello, I have found the following 3 reasons for you: 1. The glass is uneven, which causes the mobile phone tempered film to be in contact with the mobile phone screen.

This situation generally appears on the hot-bending tempered film and the cold-carved tempered film, we can try to extrude whether the bubble can be squeezed off if the tolerance is small, and the tolerance is too large is a defective product. The hot bending process of Peisheng Technology has been produced for two years, and the technical aspect has been quite mature, and the probability of this situation is only. 2. The dust on the mobile phone is not cleaned or there are bubbles caused by dust in the tempered film of the mobile phone itself, which generally cannot be removed.

3. If the AB glue is not flattened, the bubble squeeze in this case can be removed.

The treatment method of the mobile phone tempered film blistering is as follows. 1. First of all, you can use the card to scrape off the bubbles.

2. Then the bubbles are eliminated.

3. Then, if there is a bubble that cannot be pushed off, it is because there are bubbles in the internal shape of the film, which can be slowed down to paste the transparent adhesive on the film.

4. Then, gently pull the transparent glue and pull up one side of the film.

5. Finally, use another piece of transparent glue with the other hand to stick the dust off.

<>2. Then put the mobile phone on a flat desktop, and use the hard cardboard at one end of the paper towel to gather the small bubbles in the screen together, so that the big bubbles can be driven out at the end;

3. But after the above steps, some bubbles can not be completely driven out, that is, there are dust particles in those bubbles, and the dust forms bubbles in them, and we only need to take out the dust particles to remove the bubbles.

4. Cut the scotch tape one to two inches long and stick it next to the dust bubbles on the film, and then cut a small section of the scotch tape with the glue side up.

5. At this time, use one hand to pull up the transparent tape attached to the film, and use it to pull up a slit in the film, as long as you pull a seam, you can let the tape in the other hand go in.

6. After pulling it up, you can see whether there is dust sticking to the film or dust sticking to the mobile phone screen, look carefully, the dust is very fine, and then use the transparent tape on the other hand to stick the dust.

7. Done.