How to use high and low beams correctly when driving at night

How to use the high beams and low beams of the car correctly at night? There's an answer!

1. When meeting traffic on roads without central isolation facilities or center lines, high beams cannot be used within 150 meters from oncoming vehicles in the opposite direction.

2. High beams cannot be used when meeting non-motorized vehicles on narrow bridges, narrow roads without central isolation facilities or center lines.

3. When a motor vehicle is driving at night without street lights, poor lighting, or in low visibility conditions such as fog, rain, snow, sand, etc., the rear vehicle driving in the same direction and the front vehicle are driving in close proximity, and the high beam cannot be used.

4. Through sharp bends, slopes, arch bridges, pedestrian crossings or intersections without traffic signal control, high and low beams should be used alternately.

Here's how to use the night running lights.

1. The motor vehicle passes through the intersection controlled by the traffic signal and turns on the low beam at night;

2. When a motor vehicle is driving at night without street lights, poor lighting, or in low visibility conditions such as fog, rain, snow, dust, hail, etc., the headlights, marker lights and rear position lights should be turned on, but the high beams shall not be used when the rear vehicle driving in the same direction is driving in close proximity to the front vehicle. When driving in foggy days, motor vehicles should turn on fog lights and hazard warning flashers;

3. When a motor vehicle passes through a sharp bend, slope, arch bridge, pedestrian crossing or an intersection without traffic signal control at night, it shall alternately use high and low beam lights;

4. In the event of a motor vehicle breakdown or traffic accident on the road, the illumination light and the rear position light should be turned on at the same time at night;

5. On roads without central isolation facilities or without center lines, low-beam lights should be used at night when meeting vehicles in the opposite direction 150 meters away, and low-beam lights should be used when meeting cars on narrow roads, narrow bridges and non-motorized vehicles.

<> "How to use lights correctly when driving at night?

Some people think that the horn is the most direct language of the car, but the day does not understand the darkness of the night, driving at night, more important than the horn is the light, the correct use of the light is a necessary skill for the driver.

1. How to use the vehicle's own lights?

Before driving at night, vehicles should turn on their illumination lights and low beams before entering the highway. If there is a vehicle in front of you while driving, you should not use the Tono Banquet lights for a long time. When driving at night, it is necessary to check in advance whether the emergency lights, warning triangles and other necessary and commonly used tools are complete and effective.

2. How to use the "light" of the road?

When the light moves from the middle of the road to one side, it indicates that there is a curve ahead. When the lights move from one side of the road to the other, it indicates that the vehicle has entered a continuous curve. The color of the light illuminating the ground can reflect the condition of the road surface seepage, generally speaking, white is stagnant water, black is potholes, and the normal road surface is mostly gray, usually gray does not go white, and slows down in black.

3. How to use the "reflection" of the other party?

The body reflective sign is an important safety protection facility for trucks, trailers and other vehicles, and it is also an auxiliary facility for vehicle lights. Reflective markings are used to outline the body to maximize the visibility of the vehicle. Therefore, when driving at night and finding that there is a "body reflective sign" in front of you, you need to increase the safety distance in time to prevent rear-end collisions.

4. Use lights for starting and stopping at night.

After starting the engine, turn on the small lights, headlights and low beams, and then turn on the left turn signal before starting. When parking at night, use the right turn signal to pull over and slow down, then turn on the low beam to pull over, and turn off all lights after stopping.

Temporary parking needs to be turned on double flashes to indicate temporary parking. Keep this night driving knowledge firmly in mind!

Alternate operation method of leakage low beam in the distant world:After moving the light lever outward, you can turn on the high beam all the time, and then dial a gear inward, and then move a gear inward, and then move a gear inward, and the high beam will flash once to search, and after releasing the lever, the lever will automatically return to the low beam gear.

The Road Traffic Safety Act stipulates that when driving at night, drivers use high and low beams alternately in sharp curves, slopes, overtaking, arch bridges, pedestrian crossings, and intersections without traffic lights. When overtaking at night, turn on your turn signals and use your high and low beams to warn the vehicle ahead. When passing through a crossing, you need to use the high and low beam lights to change to alert the left and right vehicles at the intersection.

The first is that the high beams can be used alternately when used at night, if necessary. Do not use high beams on city roads at night. The lighting facilities of the general roads and elevated roads in the urban area are relatively good, and it is difficult to encounter dark roads at night.

Generally, when driving in such road conditions, try not to use high beams. In some roads with poor lighting conditions, in order not to affect the oncoming vehicle, the high beam and low beam can be used alternately, and the opposite vehicle should be switched immediately. When driving on the highway at night and the road ahead is unclear, you can use the high beams to illuminate the road signs and then immediately switch back to the low beams.

The second is to use high beams when meeting with cars at night. The duration of blinding varies depending on the driver's own vision and surroundings, but lasts about 2 seconds at the earliest. For these two seconds, the driver appears to be driving with his eyes closed, and his ability to observe pedestrians and oncoming vehicles is greatly reduced.

If your night vision is not good, your eye's ability to judge the speed of oncoming traffic will be affected. In this case, the interference of the high beams with the human eye accelerates the decline of this judgment.

In addition, it is important to know that high beams can improve the line of sight and expand the field of vision. On a dark road without street lights, the visible range with the high beams on is much greater than when the low beams are turned on alone. Therefore, in such an environment, it is very necessary to turn on the high beams.

From the renderings below, we can easily see the advantages of high beams.

Secondly, if you encounter the oncoming vehicle abusing the high beams to make a lot of dust, you can try to "flash" the lights to remind the oncoming vehicle to switch the high beams back to low beams. If the other party is still indifferent at this time, the driver should not act aggressively or turn on the high beam to shoot at the other party. The best way to deal with this is to reduce your speed and overtake slowly and carefully, without moving the steering wheel to avoid stray from the lane.

However, the current abuse of high beams is quite serious. Using high beams at the wrong time will not only not improve driving safety, but will increase the probability of dangerous accidents.

If there is no lighting and there are no cars or pedestrians around, you can use the high beams appropriately, but be sure to alternate the high and low beams when you meet a car.

If the road ahead is unclear and there are no other street lights, you can use high beams, but if there is a traffic situation, you should switch to low beams.

When driving at night, turn on your headlights if you encounter oncoming traffic, and turn on your high beams if you are on a poorly lit road.

Driving at night, I was deeply touched by the incivility of some people. Last Sunday, I went to my sister's house. After dinner, it was already 8 p.m.

My sister lives in Jiazhu Village, Zhifu District. There are no street lights for three or four miles north from the village. The road was not wide, potholed, and pitch black.

There are many factories on both sides of the road, so there will not be too few pedestrians. Cautiously moving forward, a car passed by, and the bright light blurred the eyes. Suddenly, when he saw someone walking in front of him, he slammed on the brakes, and later found that the person was only a few steps away from the car.

I couldn't help but break out in a cold sweat. It's dangerous!

I rarely use high beams on brightly lit city roads in Lamp Hill, but I usually use them when driving in poorly lit suburbs. However, when I encounter a passing car, I always switch the high beams to low beams. When the vehicle in front keeps the high beam on, I will use the high beam-low beam-high beam-low beam to remind the other driver to change the light.

In general, I would get the other driver's attention and change it to a low beam. But there are drivers who don't respond no matter how much you flash their lights, and they keep walking with their high beams on.

The Road Traffic Safety Law stipulates that on roads without ** isolation facilities or center lines, high beams cannot be used within 150 meters of oncoming vehicles, and narrow bridges and narrow roads without ** isolation facilities or center lines cannot be used in case of non-motor vehicles; At traffic signal-controlled intersections, high beams cannot be used when turning.

But looking at the road, some people ignore the rules and only care about the brightness in front of their cars, regardless of the safety of others. Even if the street lights are bright, the high beams are always on, and some have also modified the xenon headlights, and the low beams are not turned on and off during meetings. The oncoming light was a piercing white light, and the sky was suddenly white.

After the meeting, it was pitch black in front of me, and blind spots appeared in an instant. After a while, I reacted only to the deserving of the come, and I couldn't see the road ahead at all. As we all know, it is often this short moment that traffic accidents are likely to occur, which seriously affects driving safety.

For the illegal use of high beams or unauthorized modification of xenon lamps at night, in addition to the strict investigation of the traffic police department, the most important thing is to rely on the self-discipline of the drivers. Appeal to the majority of drivers and friends to use the high beam correctly, switch the low beam when encountering the car, and raise their hands. For the safety of others, it also adds to the security of one's own.

Millions of car purchase subsidies.

The use of night driving lights is very particular, and the use of night driving lights also conveys a lot of information.

When using a car at night, when the street lights are turned on or there are shops on both sides of the road, do not use high beams, use low beams first, and when there are no lights on both sides of the road, you should turn on the high beams to avoid timely detection of road conditions. When driving at night, the high beam should be turned into low beam in time, and if the opposite vehicle is on the high beam, it will cause instant blindness, and it is easy to be dangerous, so when the two cars are about 150 meters apart, it is necessary to switch the high beam to low beam. In the case of unclear road conditions, in order to warn oncoming traffic, high beams and low beams can be used alternately.

Especially in two-way lanes without a separation zone, it is important to alternate high and low beams. Do not use high beams on foggy days, because the lights will have a diffuse reflection effect on foggy days, which will affect the driving vision even more. Use fog lights and four-flashing lights when driving in foggy days!

Pay attention to safety when driving at night, and be sure to use lights correctly. According to the Road Traffic Act, when passing through intersections at night, the requirement for using lights is to flash alternately. This is to use flashes of light to alert other vehicles and pedestrians passing or preparing to pass in the intersection area, and to alert them to avoid conflicts when a car is coming.

If you don't use flashing, the lights at the intersection are not eye-catching enough to reflect that there are cars approaching the intersection. All traffic laws are exchanged for a lesson with plenty of blood, and an agreement is a guarantee of safety.

Be sure to pay attention to the situation when driving at night. Pay attention to the speed control of non-motorized vehicles on the right side, the traffic flow on the road at night is small, and the interference of pedestrians and bicycles is relatively small, and the driver is generally easier to drive at high speed, so traffic accidents are likely to occur at low speed; In case of bad weather such as late rain, snow and fog, you should drive at a low speed and be careful. Increasing the following distance, drivers must be ready to stop at any time when driving at night.

In this case, in order to avoid danger, it is necessary to pay attention to appropriately increasing the following distance to prevent collisions between the front and rear vehicles. If you are sure of the road conditions and feel that the speed of the vehicle automatically increases and the engine sound becomes brisk, it means that the drag is reduced during driving, and the car may be driving on a downhill road. Prepare emergency lights, and when you make an emergency stop in case of a breakdown, you can create a safe area for your vehicle.

The high beams need to be turned off when meeting the car, the low beams need to be used when meeting the car, and the high beams cannot be used when following the car.

Nighttime driving lights are very particular: when driving at night, when the street lights or shops on both sides of the road are not lit, do not use the high beams, use the low beams first. In the case of unknown road conditions, in order to warn the oncoming traffic on the opposite side, high beams and low beams can be used alternately.

Night driving lights are very particular: If you travel at night on city roads, the street lights are on, you should use low beams at this time, and if you are on a more simple and simple route, you can turn on the high beams with trousers. But none of the high beams can be used for a long time.