If the watch accidentally gets into the water, how to deal with it urgently?

The watch accidentally got into the waterThe first thing to do is to empty the water in the watch and use a hair dryer to dry it.

If there is a lot of water, you should immediately go to the watch shop to wipe the oil and remove the moisture from the surface to avoid corroding the parts. Open the back cover of the watch, handle the movement inside the watch, and then oil the various parts inside. As a result, the water in the watch causes the moisture in the moving parts of the watch to melt, which causes the parts to melt.

Therefore, the maintenance of the watch water inlet not only removes the steam from the watch, but also maintains the inside of the watch to prevent rust on the parts.

If there is not much water in the watch, which will only fog up the glass surface and will not harm the watch, at this point, you can wrap the bag tightly with absorbent toilet paper or several layers of cloth and bake it at a distance of 15 cm from a 40-watt bulb for about 30 minutes to remove the moisture. Gas. Do not bake the mirror directly next to the fire to avoid deformation of the mirror.

Alternatively, you can place the watch outwards on the inner and bottom cases and wear it on your wrist, which will remove the water after 2 hours. In life, there is also a "soil method" that is to put the incoming table in a rice pot and bury it in the dry rice for a period of time. In one night, you can see noticeable results.

Or blow dry with a hair dryer, but pay attention to the heat evenly and don't blow it into place. If the amount of water is severe, it is best to immediately send the watch factory to remove the water from the playground so as not to corrode the parts. The only way to add water to the watch is to open the back cover of the watch, process the movement inside the watch, and then oil the various parts of the movement.

As a result, the water in the watch causes the moisture in the moving parts of the watch to melt, which causes the parts to melt.

Therefore,Maintenance of the watch water inlet not only removes the steam from the watch, but also maintain the movement inside the watchto prevent rust on the parts.

What should I do if water enters my watch? Star Awareness Project

If you find that the watch is flooded, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it about 15 cm near a 40-watt light bulb, and bake for about 40 minutes, and the water vapor in the watch can be eliminated. Do not bake the watch directly near the heat, so as not to deform the glass by heating. Because although there is no moisture on the dial, there may still be water in the movement, and the movement will rust and cause damage to the movement after a long time.

After the watch is flooded, it is recommended to find a professional repair outlet as soon as possible for the master to check and deal with it, which can reduce your unnecessary losses.

Put the granular silicone gel in a closed container with the watch that has accumulated water, and after a few hours, remove the watch and the water will disappear.

Quickly wipe with alcohol to let the water evaporate, and then blow it with a hair dryer.

If the watch accidentally gets into the water, just dry the watch and put it in raw rice.

If the watch accidentally gets into the water, take it out and dry it immediately, and put it in a steel rice bag for a day.

If the water is not serious, but there is a layer of mist in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the table tightly, and bake it for about 30 minutes at a distance of 15 cm from the 40-watt light bulb, which can eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating. Send the watch shop to wipe the oil, the above three methods can not remove the water vapor, you should immediately send the watch shop to wipe the oil to remove the water of the movement, so as to avoid rust on the parts.

See if it's a waterproof watch It's okay if it's waterproof It's okay to soak it for a few minutes.

Pick the watch out of the water as fast as possible and expose it to the sun.

Quickly take it out and use the sun to blast it, and then take it to the place where the watch is repaired and repair it.

If it's waterproof, don't worry, it's useless to repair it if it's not waterproof, just replace it.

Hello, glad to answer for you!

Generally speaking, there are only three places where water can enter the watch movement: the handle (handle), the watch mask and the back cover. The waterproof device is also installed in these three places: add a rubber ring to the shank, add a rubber ring on the threaded edge of the back cover of the sealing ring, shank and other parts, and make the surface tight.

Water and fog into the watch has the greatest impact on the watch movement, and it should be dealt with in time to prolong the service life of the watch. If not treated in time, the residual moisture will easily cause the internal movement to oxidize and rust, resulting in inaccurate watch timekeeping and watch failure.

If the watch is seriously flooded, please send it to the repair center immediately for treatment, otherwise it will cause many metal parts inside the movement to oxidize and rust due to water vapor, causing greater damage.

If you are using a vivo watch, wearing the watch for hand washing, swimming, etc., water droplets may enter the speaker opening of the watch, it is recommended to throw out the water droplets from the watch speaker with a little force, and then wipe the body with a clean soft cloth and wait for the water droplets to evaporate. If the watch cannot be used normally, please go to the vivo customer service center for testing.

Customer service center address: enter the vivo official website vivo**app--my--service outlets after-sales outlets--select provinces and cities to inquire about the customer service center address) It is recommended to call the customer model Kaifeng service center in advance to confirm relevant matters and understand the working time, so as not to delay the precious time between grandchildren.

If the watch gets into water, the following measures should be taken:

Stop using the watch immediately and avoid pressing any buttons or turning the crown to avoid further water entering the inside of the watch.

Gently wipe the watch surface and strap with a dry, soft cloth, and place the stove dial facing down in a dry place to allow the moisture to evaporate naturally.

If the water ingress of the watch is serious, the watch should be sent to a professional repair center for overhaul and repair as soon as possible to avoid rust or damage to the internal parts.

Before sending it in for repair, you can try to put the watch in a sealed bag and add some desiccant, such as dried rice or silicone, to absorb the moisture inside.

In short, water ingress into the watch is a troublesome thing and needs to be dealt with in time. If the water ingress of the watch is more serious, it is best to send it to a professional repair center for overhaul and repair.

1. After the watch fell into the Xinxiao water bend, immediately take the watch out of the water and wipe the water on the surface with a dry towel.

2. Prepare a hair dryer and turn on the switch. Switch the hair dryer to the hot air setting, use the hair dryer to blow the watch, and slide the balance so that the water inside can evaporate. When the moisture is almost gone, it should be fine.

4. If you don't have a hair dryer, you can also take it to the sun to dry, and the water will also evaporate, and the drying speed may be slower. As long as the moisture is gone, there should be no problem with the watch.

The solutions to the water in the watch are: wrap the watch in toilet paper, turn the watch upside down, put it in a rice bucket, put it with desiccant, and put it with silicone.

1. Wrap it in toilet paper.

If the watch is soaked in water, you can wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, put it at a distance of about 15 cm near a 40-watt light bulb, and bake it for about 30 minutes. Do not bake the watch close to the fire, so as not to deform the watch by heat.

2. Turn the watch upside down.

Put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

3. Put it in a rice bucket.

You can also put the watch in the filial piety rice bucket, the rice bucket is generally relatively dry, and the rice grains will also suck out the water vapor in the watch and leave it overnight.

4. Put it together with desiccant.

If the watch gets into the water, you can put the watch and desiccant together and wrap it in plastic wrap. After 24 hours, the watch will dry and will not be contaminated by dust.

5. Put it together with silicone.

Stir the granular silicone with the water accumulation watch and put it in a closed container, and after a few hours, take out the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch. The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the ability to absorb water and bend can be renewable, and it can be used again and again.

Since some watches are not waterproof, they are prone to water ingress. What should I do if the watch gets water? PChouse will take you to find out.

1. Dry the granules with silica gel. If water enters the case, you can use a granular substance called silicone to put the watch in an airtight container with the waterlogged watch, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

2. Bake with a light bulb. If the water ingress is not serious, but there is a layer of mist in the surface glass, then you can use several layers of potato toilet paper or flannel cloth that is easy to absorb moisture to wrap the table tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes, which can eliminate the water and gas. Do not bake the watch mask directly close to the fire, so as not to deform the watch due to heat.

3. Wear the watch backwards. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe. (It is not recommended to use the above methods to deal with it, it is recommended to go to the after-sales center for maintenance).