What is going on with the router that sends more data and receives less?

TTL doesn't care about it, just look at what the value of time is, what you see is time=1ms, which means that the response time from your computer to the router and back is 1 millisecond, which is already the best state.

As for the problem of sending and receiving data, it depends on your usage, when you are in a larger file, you should receive more and send less, if you still send more and receive less, there are two situations, one is that the computer software shares your files, such as the previous use of Thunderbolt will be provided to other people, that is, others have something to get some data from your computer, as long as the software such as Thunderbolt is turned off; The other situation is the external network problem, which you can't control, and the server of the positive thing is not powerful or the network operator is not powerful. It is recommended to install a 360 to minimize the software that runs on the boot, and only keep the programs it recommends to leave behind.

More data sent, less data received?? I don't know what it means!! Are you talking about the uplink rate vs. the downlink rate!!

If it's maybe some software installed with Thunderbolt, these pop** software will be uploaded when you open it!! You go to the service and turn off the pop service!! Isn't it a problem!!

But remember to look!! Just to show you!! Identify the problem!!

The wireless router only sends data but does not receive data Reason: Check whether the router dials up.

Check method: Method: Enter the router to check whether the WAN port status shows data, not all of it is displayed, the following figure represents that the router is normal.

If all displays 0, it means that the router dialing needs to be set.

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoE Dialing] (some are ADSL dialing), enter the username and password (provided by the network service provider) according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Go to the router settings page, enable DHCP in it, and set the computer to "automatically obtain IP address" and "automatically obtain DNS server address".

Use. Router settings.

Wi-Fi, sending less data than receiving, is the case.

Packet loss rate. High.

Packet loss, as the name suggests, refers to the loss of communication packets in communication.

Data is transmitted in packets on the communication network, and each packet contains frames that represent data information and provide data routing. This means that no matter how good the network is, the data is not transmitted continuously in a linear (like playing **), and there are always holes in between.

The transmission of data packets cannot be completed 100% because of physical grinding.

Line fault. Equipment failure.

There will always be certain losses due to virus attacks, routing information errors, etc. In this case, the network will automatically let both ends of the communication make up the packet according to the protocol. If the line is in good condition and the speed is fast, the loss of packets will be very small, and the work of repairing the packets will be relatively easy to complete, so the data can be approximated as lossless transmission.

However, if the line is poor (such as.

modem, the amount of data loss will be very large, make up.

package work. It can't be 100% done. In this case, the transmission of data is voided, resulting in packet loss.

Resolution. The solution is as follows: After disconnecting from the network.

Safe mode. Check and kill viruses, shorten the length of the network cable appropriately, check the network cable and remake it.

Crystal head. Reinstall the operating system, adjust the NIC or network device to work at the same frequency, change the NIC or change the environment of the network device, or change the network device.

Network operators. Settle.

1) If it is a problem with the broadband itself, first directly connect the broadband network cable to test, if it is a broadband problem, contact the broadband customer service to solve it.

2) If it is a problem with the router, if it can be used originally, it cannot be used for the time being, and my practice is to disconnect the power supply of the router and plug it in, and I will take a look. After there is a factory reset, it can be used from the new settings (this is on the premise that the physical connection is correct).

If it can't always be solved, it is recommended to call the customer service of the router, he has **** guidance, and when you encounter a problem that you can't solve, it is very useful to consult the advice he gave, and he will give correct suggestions for the settings or operations.

3) If it is caused by a system problem, it is recommended to restore the system or reinstall it.

4) If you turn off the wireless switch, if you use the software to connect the wireless, it is normal for the software to be difficult to use and often have problems, there is no better way, use a router. In addition, it is caused by the network card driver is not or is not suitable, and whether there is a problem with the network cable interface or network cable.

The meaning of sending packets: it is the number of data packets you apply, for example, you will have traffic on the meaning of receiving packets: you apply, and the server is yours. The problem for you may be that the internet is disconnected.

Slow internet speeds. It could be that the network is not working or there is a problem with the router**! And now the state-run network is blocked routers, you know this! (There is also a possibility that an ID in the LAN is using too much traffic).

If it is a network problem, you can call the broadband service** to report the problem.

If it's a router** problem: set up your router! (The easiest way is to restore factory settings) if the router is blocked:

Restarting your router can do the trick! If it is troublesome to restart the router, you can upgrade the router or replace it with a newer version to reduce the number of times it is blocked. (Nowadays, network operators use scanning engines, and "Network Warrior" is an immature software, and major router companies have many ways to deal with it.)

Of course, you can also rely on software"Cyber Aegis"Lie to it. As the saying goes, one foot high, one foot high).

Hope it helps. Hope to give, thank you.

What do you mean? I didn't get it.

Receiving network Didn't understand what was being said.