About turning on the low beam before starting at night

Start with low beams, then alternate.

Poor visibility at night, using lights is the key to safe driving. Therefore, the following should be paid attention to when using lights:

1. The turning time of the car lights should be the same as that of the street lights. If it is cloudy, foggy, windy or rainy, you should turn on the lights in advance to ensure good visibility.

2. Turn on the lights before starting and see the road ahead before driving. When parking, you should stop first and then turn off the lights.

3. If the speed is less than 30 kilometers per hour, low beams can be used, and high beams should be used if the speed is more than 30 kilometers. On roads with street lights, turn on the low beams.

4. When passing through an intersection with traffic police command or traffic lights, the headlights should be turned off at a distance of 30 to 50 meters from the intersection and small lights should be used instead.

5. When temporarily parked on the side of the road, turn on the small lights, tail lights and width lights.

The new regulations stipulate that the use of high beams when turning at intersections, the use of high beams when driving on roads with street lights and good lighting, and the use of high beams when passing through sharp bends, slopes, arch bridges, pedestrian crossings or intersections without traffic signal control, will be judged as unqualified if they do not alternately use high and low beams, and these points have been done by the trainees, which is very important, because at night when pedestrians cross the street is sometimes a shadow, not alternately using lights, it is difficult to ensure that the driver finds the situation in time, causing accidents.

When starting at night, of course, you have to look close, so turn on your low beams. If you turn on the high beams, you won't need it when you start. Low beams, as the name suggests, are to illuminate the entry and exit, and the start is just beginning, so use low beams.

If you're starting at night, I also recommend turning on the double flash and turning it off when the start is complete.

Personally, I didn't start at night either

Low beams are mainly in cities, first of all, cities have street lights. And if there is a vehicle on the opposite side, you should turn on the near lights, and turning on the far lights will affect the other party. Turn on the far lights in places with few people on the highway, so that you can see the distance more clearly.

When driving on the highway at night, do you turn on the high beams or low beams? Whether it is for old drivers or novice drivers, the three words "Yuanguang Dog" can be described as "deeply rooted in the hearts of the people"! Many new and old drivers have this question - do they use high beams or low beams when driving at high speeds at night?

Xiao Wan is here to tell you that if you are driving at high speed at night, it is best to turn on the high beams. First of all, most of the high-speed sections have isolation belts, and the use of high beams in general family cars and SUVs will not affect the oncoming cars on the opposite side, so you can use them with confidence. Secondly, most of the high-speed sections do not have street lights, if you use low beams, the lighting situation will be poor, in the case of fast speed, what conditions on the road may not have time to react, easy to cause accidents.

Of course, if you pass through a highway section without a separation zone, when there is an oncoming car on the opposite side, you still have to switch to low beam to avoid obstructing the view of the oncoming traffic. After the interaction between the cars, switch to the high beams and continue driving. If the other party's high beam gets in the way, you can switch the high and low beam three times in a row to remind the other party that if the other party cuts the low beam, you can also cut the low beam, and if the other party does not react, you can also continue to use the high beam, there is no need to be humble in this situation.

Apart from the highway, what sections of the road are it necessary to use high beams?

If the road lighting is not good in the non-high-speed section, you can use the high beam first, and the opposite car will switch in time to ensure safety.

In addition, we should also remind everyone to pay attention to one point, do not use headlights because the road lighting is enough, the headlights of the vehicle have two functions, the first is to let others see you, and the second is to illuminate the road in front of you, especially in the tunnel, it is recommended to turn on the headlights, so as not to cause accidents when other vehicles can not see your car when changing lanes. Rational use of lights, scientific use of lights, and standardized use of lights, so as to ensure the safety of car travel, I hope to help new and old drivers.

It must be on the low beam, just starting out to grasp the basic situation of the road, and try not to turn on the high beam when the car will be at night, it is not safe, turn on the low beam to help mediate their eyesight, if you turn on the high beam at the beginning, your eyes will be very adapted to the strong light environment, once you enter the dark area, your eyes can not recover quickly, it is recommended to keep the low beam, special circumstances open the high beam!

It must be a low beam, and a long shot is generally not used.

To open the low light, I just took the first exam yesterday and has this question, which is the original question in the question bank!

Should I use "high beam" or "low beam" when driving at high speed at night? The old driver tells you the answer.

That's right, dipped beams for indoor driving at night. Turn on the high beams when driving on the highway at night, but when you meet the car, you need to be 150 meters away from the other party, and change to low beams. Because the light of the high beams is relatively strong, there are more vehicles and pedestrians in the city at night.

Strong light exposure can affect the vision of pedestrians and drivers of vehicles on the opposite side, and it is easy to cause danger. When walking at high speed at night, drive high beams and keep a distance of 100 meters from the car. Turning on the high beam is convenient for the driver to observe the road conditions ahead, and turning on the high beam is also convenient for the opposite motor vehicle to detect it early and make a reminder of the alternation of far and low lights in advance.

Low beam. In night driving, if the speed is less than 30 kilometers per hour, low beams should be used, and under normal conditions, the lights can shine more than 30 meters. When passing through an intersection, slow down at a distance of 50 100 metres from the junction and turn on the high beams to low beams while turning on the turn signals to indicate the direction of travel.

When the opposite car is 150 meters apart, the high beam should be changed to low beam, which is to avoid obstructing the sight of the opposite driver, if the other party does not change to low beam, should immediately slow down and continuously use the method of changing the far and low beams to signal, if the other party is still bright and does not change, then should slow down and stop on the right to avoid, do not fight with strong light, so as not to damage the vision of both sides and cause a car accident.

When the car starts at night, do not turn on all kinds of lights, because the current required for the car to start is very large, and the current of other electrical appliances will suddenly weaken at this time, which will cause damage to the electrical appliances. In addition, starting the car is a split second, so there is no need to turn on the low and high beams.

You are talking about starting, not driving, starting the car at night, turning on the low beams, or small lights, when driving, in the mountains or places with a small number of cars to turn on the high beams, in the city roads or on the road with street lights to turn on the low beams and turn off the high beams, other lights generally can not be turned on, the width of the light fog lights can only be turned on when the fog.

Turn on the low beam, turn on the high beam when driving, and turn on the headlights when the car comes from the opposite side and change the low beam!

Before starting at night, the low beam should be turned on. （）

a.That's right. b.Mistake.

Zhengchang shirt has a hidden answer: a

Turn on the low beam before starting at night. The following are the precautions for driving at night: 1. Before starting at night:

Turn on the low beam before starting at night; Then observe the situation around the vehicle to make sure that it is safe before starting. 2. After starting at night: change to high beams according to road driving and visual conditions when the road allows.

The prerequisite is that the oncoming road is not following a moving vehicle or with its high beams on. 3. When driving at night: when the speed is less than 30 kilometers U002F hours, low beam lights should be used, and the lights can shine out 30 meters away under normal conditions.

When passing through an intersection, slow down at a distance of 50 100 metres from the junction and turn the high beams into low beams, and turn on the turning silver lights to indicate the direction of travel. When the oncoming vehicle is 150 meters apart, the high beam should be changed to low beam to avoid obstructing the view of the oncoming driver.