The capacity of the portable hard disk does not match the actual capacity

First of all, you can first go to computer management - disk management to see, whether there is no space that has not been partitioned, if there is a partition first, and then see if there is a hidden partition, the general computer manufacturers in the computer before the factory, will set up a hidden partition, used to place the system factory state of the mirror, about a dozen g... Computer management interface: Enter "in "Run" to enter.

If it still doesn't work, you can see if there are a lot of hidden files in the computer, to view these files, you can open my computer, Tools folder option (window7, in the "organization"), select the view tab, put the "show the contents of the system folder" and "show all files and folders" The two options are checked, and then remove the "Hide protected operating system files" check, you can see all the files and folders under the windows system. There's also antivirus.,You can use a little red umbrella.,It's very good.,Better than Rising and the like.。。。 That's all, hope it works for you! ~~

No partition will take up a part of the space to make the cache capacity, and it is impossible to display as much as the hard disk is.

Normally, the hard disk manufacturer is pressing 1g

1000m counted.

And the system is pressed 1g

1024m counted.

So it looks like there's a lot less space.

Hard disk manufacturers are not kind to this, and the standard is calculated according to 1024.

Format it and take a look, if it doesn't work, delete the volume from the hard disk management, and create a new one!! I've had it too!!

The display capacity of the hard drive does not match the actual one.

The nominal capacity is not the same as the actual capacity.

The algorithm is different. So it's not the same.

Check to see if there are any hidden partitions or hidden files.

Why can't it be displayed? If it is on the computer, right-click on the computer, Guan Jing quietly, Disk Tube Mountain Type, check whether the storage space of the mobile hard disk is displayed, if there is a partition but there is no drive letter, you can right-click to assign a drive letter, and then you can use it.

The portable hard drive shows the drive letter but has no capacity, and needs to be formatted.

The steps are as follows:

1. Click Open My Computer to enter the disk partition directory page.

2. Select the portable hard disk on the disk partition page and right-click.

3. Select Format in the right-click menu.

4. Click Start.

5. After formatting, the disk capacity can be displayed.

It is because the mobile hard disk has a disk bad sector, but it is not a non-fatal bad sector, so it can be solved by borrowing software to repair the bad sector of the mobile hard disk.

Here's how to fix it:

1. Open the browser under the Windows system and enter "low-level format of mobile hard disk".

<>3. After the installation is completed, open the "Mobile Hard Disk Low Level Format" software.

4. Select the portable hard drive you want to repair the bad sectors and click Continue.

5. In the pop-up window, select "Low-level Format".

6. Finally, select "Format this device" in the lower left corner to solve the problem.

If the portable hard drive displays a drive letter but has no capacity, it may be due to a corrupted partition table or file system. Here are three solutions for you:1

Use Disk Management Tool: In Windows operating system, you can use Disk Management Tool to repair hard disk partition tables or file systems. Open the Absentee Computer Management window, and then select Disk Management.

In this window, you can check the status of the disk, reassign partitions, modify the file system, and more. 2.Use the command line tool:

If you are used to using the command line, you can also use the command line tool to repair the hard drive. Open a command prompt window (run as administrator) and type "chkdsk fr", which is the drive letter of the disk you want to repair. 3.

Try using data recovery software: If none of the above methods can fix the hard drive error, it is recommended to try data recovery software. These software can scan damaged file systems and partitions and try to recover lost data.

Commonly used data recovery software is Recuva, Easeus Data Recovery, and so on. Note that before attempting to repair your hard drive, always back up your important data and make sure that you take proper precautions to avoid data loss.

The portable hard drive shows the drive letter but has no capacity, and needs to be formatted.

The steps are as follows:

1. Click Open My Computer to enter the disk partition directory page.

2. Select the portable hard disk on the disk partition page and right-click.

3. Select Format in the right-click menu.

4. Click Start.

5. After formatting, the disk capacity can be displayed.

Hello, I have seen your question, and I am sorting out the answer, please wait for a while 1. Click to open my computer and enter the disk partition directory page; 2. Select the portable hard disk on the disk partition page and right-click.

Questions. I didn't respond to it.

3. Select Format in the right-click menu. 4. Click Start. 5. After formatting, the disk capacity can be displayed.

Questions. Including device management, disk management is useless.

Wait a minute, let's analyze it here.

Questions. If you don't respond to it now, you can't format it.

It's just that if it doesn't work, you have to format it.

Questions. Clicking the mouse didn't respond to how to lattice the ruler.

Pro, there is a problem with the mouse.

Questions. Didn't you say that, didn't you say it?,Is it normal to have a problem with the mouse?。

There was a problem with the system assigning a drive letter and it was not assigned a drive letter. It's actually connected. Right-click, My Computer, Manage.

Then click: Disk Management, and the move disk appears at the bottom right. Right-click, change the drive name and path, change, and then manually specify a drive letter.

You can also right-click and open it directly, but at this time, the address bar shows no path.

If it still doesn't work, just reinstall the system.