How to change the access code of the COUNS model CU K05

There are two cases:

1. If the initial password has not been changed, it can be changed in this way:

0 New Password Repeat New Password * is the asterisk key).

2. The initial password has been changed, you can change it like this (but you must be cautious, it is best to recommend professionals to operate):

Initial password recovery first, as follows:

Turn off the power first, then dial "reset" to the "on" position, power on, ring three times, and then dial back to the "off" position.

Note that after the restoration, the card that has been issued will no longer be able to open the door and will need to be re-registered. So be sure to operate with caution.

Then change the password in the previous case.

1. Initial password: The programming password is 9999.

2. Enter the programming state: Press * Programming password to enter the programming state.

3. Function settings: Modify the programming password: Press * Programming password 0 New password Repeat new password * Note: The password is 4-6 digits of any number.

In this way, the access code can be changed.

COUNS-K05 manual.

When you enter programming, you can look at the indicator light prompt or the sound prompt to judge whether it is correct. couns-k05

The programming password at the factory is 9999.

Change programming password: Press * 9999 0 New password Repeat new password Note: The password is 4-6 digits. Note that the programming password is not the door opening password.

Modify the door opening password: press * programming password 9999 5 + new password (4-6 digits) new password access control programming is the administrator who enters the program, it is impossible to open the access control, and if you want to open the access control, you must set the access control door opening password.

Pay attention to the features you want to implement.

Couns - This brand is Guangzhou Gaoyou, ask them!

Nowadays, people just like bargains, regardless of where the brand is, where the manufacturer is, and whether the service keeps up!

Find a professional person to replace!

How to set up and use:

1. Initial password: The programming password is 9999.

2. Enter the programming state: Press * Programming password to enter the programming state.

3. Function settings:

1) Change the programming password: Press * Programming password 0 New password Repeat new password * Note: The password is 4-6 digits of any number.

2) Add user card: Press * Programming password 1 to read the card Enter the card** * Note: The ** of the card is 001-999 non-repeatable three digits, and you must enter **, otherwise the card is invalid.

If you need to add cards consecutively, you don't have to press to read the second card directly after losing the three-digit **.

3) Delete the user card (there are three ways):

a. Press * Programming Password * to delete all macro account cards;

b. Press * Programming password 2 Read card * Delete the card being read;

c. Press * Program password 2 The card** * Delete the lost card;

4) Set the door opening mode

Press the Programming Password to read the valid card to open the door.

Press the Programming Password to read the card plus the password to open the door.

Press the Programming Code to read the card or password to open the door.

Note: The factory settings are to read the card or password to open the door;

6) Set the public door opening password: Press * Programming password 5 New password Repeat new password * Note: The password is 4-6 digits of any number.

5. How to use:

1) Read a valid card in normal working condition to open the door;

2) If you need to read the card and add the password, enter the correct password within 10 seconds after reading the card to open the door;

3) If you have forgotten the programming password, you can use the jumper switch "reset" on the motherboard to restore the factory settings. Turn off the power first, dial the jumper switch to the "on" position, and then turn on the power, and then dial the jumper switch back to the "off" position after the buzzer rings three times to restore the factory settings.

Note: 1. Please turn off the power first when installing the wiring, and do not operate with electricity!

2. Under normal circumstances, the electric lock is connected from the power controller.

Summary. Hello, we are glad to answer for you: the initial programming password of the COUNS access control model CU-K05 is 8888, and the use password is 0000.

2.Then press the "* button" on the CU-K05 access control, enter the programming password, and then press the " " button to enter the programming state.

3.After entering the programming state, enter the number 0, then enter the new password, press the " " key, enter the new password again, and finally press the " " key and the "*" key in turn to end, so that the password is reset (it should be noted that the password is 4-6 digits of any number).

4.Not in the programming state, press the "* key to read the user card, the green light flashes, press the use password, and then press the " " key to enter the password change program, enter a set of four-digit new passwords, press and then enter the new password again, press the " " key and the "*" key to end.

Couns access control password K05C

Hello, I am glad to answer for you: the initial programming password of the CUUNS access control model CU-K05 is 8888, use the password to then press the "* key" on the CU-K05 access control, enter the programming password, and then press the " " button to enter the programming state from the thick number. 3.

After entering the programming cavity first state, enter the number 0, then enter the new password, press the " " key, enter the new password again, and finally press the " " key and the "*" key in order to end, so that the password is reset (it should be noted that the password is 4-6 digits of any number). 4.Not in the programming state, press the "* key to read the user card, the green light flashes, press the use password, and then press the " " key to enter the password change program, enter a set of four-digit new passwords, press and then enter the new password again, press the " " key and the "*" key to end.

I hope the above is helpful to you If you are satisfied with me, please give me a thumbs up

Summary. Hello dear, proximity card password access control manual CU-K03 The steps to change the password are as follows:

Open the door password to change press the * word key + programming password and then press 5 Enter the door opening password you want to change Confirm, and then enter the door opening password you modified again Confirm, press the * key to exit, and the modification is successful! Press the password plus to open the door.

Proximity card access control:

1) Selection of sensor: In high-end hotels and office buildings, you can choose a high-sensitivity sensor; In places where people often pass by, such as banks and shops on the sidewalk, choose a microblog sensor in a narrow area (the sensors are adjustable).

2) Safety auxiliary device: In high-end hotels and other places where it is necessary to eliminate the induction of the induction of the incident, you can choose to install an anti-pinch infrared sensor.

3) Equipped with backup power supply: In order to ensure that the automatic door can also work normally in case of power failure, it can be equipped with backup power supply.

I hope mine is helpful to you, if you are satisfied with my service, don't forget to give a thumbs up, thank you! Happy work and life! <>

Proximity card password access control manual CU-K03 how to change the password.

Hello, I am glad to serve you, I have received your question, and I am sorting out the answer for you, it takes time to guess the word on the bridge, and please be patient and wait for a while, and answer it for you immediately! Potato eyes.

Hello, proximity card password access control manual CU-K03 The steps to change the password are as follows: open the door password to modify the * word key + programming password and then press 5 Enter the door opening password you want to change Confirm, and then enter the door opening password you modified again Confirm, press the * key to exit, and the modification is successful! Press the password plus to open the door.

Proximity card access control: 1) Selection of sensor: In high-end hotels and office buildings, you can choose a high-sensitivity brightness adapter; In places where people often pass by, such as banks and shojing morning finger stores, choose a microblog sensor in a narrow area (the sensors are adjustable).

2) Safety auxiliary device: In high-end hotels and other places where it is necessary to eliminate the induction of the induction of the incident, you can choose to install an anti-pinch infrared sensor. 3) Equipped with backup power supply:

In order to ensure that the automatic door can also work normally in the event of a power failure, it can be equipped with a backup electric opening and rolling source <>

I hope mine is helpful to you, if you are satisfied with my service, don't forget to give a thumbs up, thank you! Happy work and life! <>

How to set up and use:

1. Initial password: The programming password is 9999.

2. Enter the programming state: Press * Programming password to enter the programming state.

3. Function settings:

1) Change the programming password: Press * Programming password 0 New password Repeat new password * Note: The password is 4-6 digits of any number.

2) Add user card: Press * Programming password 1 to read the card Enter the card** * Note: The ** of the card is 001-999 non-repeatable three digits, you must enter **, otherwise the card is invalid.

If you need to add cards consecutively, you don't have to press to read the second card directly after losing the three-digit **.

3) Delete the user card (there are three ways):

a. Press * Programming Password * to delete all user cards;

b. Press * Programming password 2 Read card * Delete the card being read;

c. Press * Program password 2 The card** * Delete the lost card;

4) Set the door opening mode

Press the Programming Password to read the valid card to open the door.

Press the Programming Password to read the card plus the password to open the door.

Press the Programming Code to read the card or password to open the door.

Note: The factory settings are to read the card or password to open the door;

6) Set the public door opening password: Press * Programming password 5 New password Repeat new password * Note: The password is 4-6 digits of any number.

5. How to use:

1) Read a valid card in normal working condition to open the door;

2) If you need to read the card and add the password, enter the correct password within 10 seconds after reading the card to open the door;

3) If you have forgotten the programming password, you can use the jumper switch "reset" on the motherboard to restore the factory settings. Turn off the power first, dial the jumper switch to the "on" position, and then turn on the power, and then dial the jumper switch back to the "off" position after the buzzer rings three times to restore the factory settings.

Note: 1. Please turn off the power first when installing the wiring, and do not operate with electricity!

2. Under normal circumstances, the electric lock is connected from the power controller.

The first is to clear zero, and then go to set a new password.

I have already changed the initial password and want to change the password, how do I set it?

The password of this model can be reset, mainly secretly, and then enter the password on the line.

Not our product I don't know.

Summary. Dear, hello, I'm glad to answer for you, answer couns access control model CU-K05 password can be reset in this way The initial programming password of COUNS access control model CU-K05 is 8888, and the use password is 0000. Then press the "* button" on the CU-K05 access control, enter the programming password, and then press the " " button to enter the programming state.

After entering the programming state, enter the number 0, then enter the new password, press the " " key, enter the new password again, and finally press the " " key and then the "*" key to end, so that the password is set again (note required.) When not in the programming state, press the "*" key to read the user card and the green light flashes, press the use password, then press the " " key to enter the password change program, enter a new four-digit password, and then enter the new password again.

How to reset the password of CUUNS access control model CU-K05?

Dear, hello, I'm glad to answer for you, answer couns access control model CU-K05 password can be like this hidden ridge to reset the initial programming password of couns access control model CU-K05 is 8888, use the password is 0000. Then press the "stove infiltration*" button on the CU-K05 access control, enter the programming password, and then press the " " button to enter the programming state. After entering the programming state, enter the number 0, then enter the new password, press the " " key, enter the new password again, and finally press the " " key and then the "*" key to finish, so that the password is set again (you need to bet on it.

When not in the programming state, press the "*" key to read the user card and the green light flashes, press the use password, then press the " " key to enter the password change program, enter a new four-digit password, and then enter the new password again.

After the new password is set, then press the rice word, and the green light is not on.

The fingerprint lock battery is insufficient, and a low-voltage alarm will be issued when the fingerprint lock is about to run out. Poor contact of the fingerprint lock battery may lead to the occurrence of such a situation, at this time, the backup battery can be used to start the door lock system unlocking, or you can use the emergency mechanical key to unlock, and adjust the fingerprint lock battery after entering the door to make the fingerprint lock work normally. It may be that the door lock is not energized, and the emergency power supply is used to power on the operation, and the battery or rear motherboard can be replaced.

The software freezes, you need to press the core branch reset button, and use a sharp object to touch the switch.

It's not a battery, it's a 220-electric one.

Fingerprint lock battery contact is not good, potato tease may lead to the occurrence of such a situation, at this time you can use the spare battery to start the door lock system unlocking, you can also use the emergency Wang mechanical key to unlock, after entering the door to adjust the fingerprint lock battery, so that the fingerprint lock works normally.

It may be that the door lock is not energized, and the emergency power supply is used to power on the operation, and the battery or rear motherboard can be replaced.

This is not a fingerprint lock, it is a lock with a card.

Then you can only call after-sales to get it for you.

The main thing is that the new password is set, and then press the meter button and the green light is shining, how to do this?

What do you do when you're done?

It's done.