How to paste PVC self adhesive wallpaper so that it does not bubble

For the best results, the wallpaper should be applied to a smooth surface, and the surface of the wall must be dry and free of mold, oil or other dirt. If you stick wallpaper to a rough surface, you should first grind it with sandpaper and wash it with water or a neutral detergent to avoid affecting the use effect.

Tailor the product to the size of the surface to be pasted. It is better to leave a margin of about 5cm. Tear the film from the bottom paper, pull the film forward with one hand, and flatten the surface of the film from the middle to both sides with the other hand. It is easier to smooth with a soft cloth.

When you start pasting, it is recommended that you stick it along the wall from top to bottom, and gently accumulate bubbles and folds from the middle to both sides. Large bubbles that can be punctured with a needle to squeeze out the air.

Self-adhesive wallpaper pasting method:

1. Wipe off the dust and oil stains and other pollutants on the surface of the position to be pasted and dry it (the surface of the paste should be flat and not wet).

2. Hold the sticker in hand before pasting it, and then measure the cropping.

3. From top to bottom, carefully paste the wallpaper, gradually remove the bottom paper on the back, remove the bottom paper at the same time, use a soft cloth or towel to gently smooth the wallpaper ** to both sides, and discharge all the bubbles to ensure a smooth effect.

4. If there are bubbles after pasting, prick it with a needle and run away from the air.

1. Carefully inspect the wall, if there is a hole or protrusion, fill it with putty, and level the wall with a scraper. In order to ensure smooth application, it must be kept dry and free of mold, grease or other dirt. If the surface of the object is rough, it must be sanded smooth and scrubbed with water or a neutral detergent to prevent the overall effect from being affected.

2. Measure the size of the wall, and measure the wallpaper based on the area of the wall, pay attention to the length of the wallpaper 5cm more than the actual veneer.

3. Separate the film from the bottom paper, and then paste it along the wall from top to bottom, and then gently accumulate folds from the middle to both sides, and the slightly larger bubbles can be punctured with a needle to squeeze out the air.

4. When encountering a power switch or socket, you can first cover the wallpaper on it, then brush it flat with a wooden handle brush, and use a utility knife to spend a cross in the form of a diagonal line on it, and then use a wooden handle brush or scraper against the edge of the switch, and finally use a utility knife to cut off the excess part along the edge of the switch.

5. If you encounter the connection of the printed style wallpaper, find the same position of the pattern in the place where the two wallpapers meet, overlap and paste about 12cm wide, wait until the whole wallpaper is all aligned, and then use a scraper to resist, and cut the overlapping part with a sharp knife.

6. Finally, when dealing with the wallpaper around the doors and windows, the method is the same as the wallpaper treatment method at the power switch.

Self-adhesive is not easy to stick, easy to blister and fold.

Now there are many types of wallpaper, there are a lot of patterns and colors, and it is a more popular decoration material, but sticking wallpaper is a process work, and it is very important to paste it wellHow do you stick the wallpaper so that it doesn't blister? What should I do if the wallpaper posted at home is not good-looking? Let's find out!

How to paste the wallpaper so that it does not blister

The first is to check the flatness of the wall, smooth out the uneven areas on the wall with a spatula or other tool, and then clean the wall.

Then apply putty to make the walls smoother. After the putty is dry, apply a layer of primer to the wall, and after the primer is completely dry, you can start to draw the vertical line, measure the vertical reference line with a cross center hammer, start from the corner of the Chunhui wall, draw along the vertical reference line with a pen, and finally paste the wallpaper.

What should I do if the wallpaper posted at home is not good-looking?

If it is for construction reasons, the wallpaper is ugly and not good-looking. That is to say, in the construction process due to the pattern splicing caused by asymmetry, wrinkles, tilt and other problems, the construction personnel can modify in time, because the wallpaper is still wet when just pasted, it is easier to correct it. Once it's been a long time, it's hard to fix.

If you don't like the wallpaper after pasting, you can only replace it, tear off the wallpaper, and then paste the new wallpaper.

If you are still not satisfied after trying the above methods, the solution is to remove the original wallpaper and replace it with a suitable color paint to remedy the second decoration. Paint construction is best carried out in good weather, which can be air-dried in time to avoid moisture on the wall.

How to paste the wallpaper so that it does not blisterWhat should I do if the wallpaper posted at home is not good-looking?

How to remove self-adhesive foam wallpaper glue; How to clean foam glue off wallpaper: alcohol. For wallpaper, cleaning the wall foam glue with alcohol will not cause much damage to the wall, but the volatilization of alcohol can minimize the damage to the wall by cleaning.

Salt. This method uses physical friction. However, because salt is a white crystal, there is no need to worry about the strange color of the wall caused by friction.

In the process of rubbing, you can use white gauze or cloth that can wrap salt, wrap a small packet of salt, rub gently, and slowly you will find that the foam glue left on the wallpaper is slowly disappearing, and in turn sticking to the fabric, you just need to stop while rubbing to remove the clumps of foam glue on the gauze. Scrub cloth. This method is more harmful to the wall paint, because if you are not careful, you may grind into the wallpaper itself.

Hello, dear is very high, Jian Yinxing can answer this question for you. <>

What to do with foam wallpaper non-adhesive tape: If the wall cloth can't stick to the adhesive tape, you need to use wall cloth adhesive to stick it. The wall cloth is glued to the wall before it is glued.

The wallcovering paste needs to use non-woven wallpaper glue, and the glue can not be directly applied to the back of the wallcovering, but should be painted on the wallcovering, and it can be evenly coated with 2mm. When pasting the wall cloth, the glue is required to be thicker and thicker than other wall glue, so that the fluidity of the glue is not so strong.