There are several ways to partition a hard drive

1.The built-in fdisk partition command can be run under DOS.

Enter dos and run fdisk

2. Use partitioning software PQ magic or diskgen, the specific method, there are these, you can take a look at it in detail.

Several ways to partition learn tutorials:

1. fdisk partition method:

2. DM partitioning method:

3. Use partitionmagic to adjust the partition capacity

I've got all the hands.,Can you add more points?,Thank you.。

Good luck! 1

You can take a kitchen knife and divide it into several districts if you want to, and the kid dares to ask questions without points.

Enter dos and run fdisk

2.I do it with Windows computer manager and see the figure.

fatfat32

If you want to know more about NTFS, you can try to reinstall the system.

How do I partition a newly bought hard drive? What is the hard drive partitioning method? This is something that noobs need to understand, and in general, the hard disk partitioning principles are:

No matter which partitioning software we use, we should follow the following order when creating partitions on a new hard drive: Create Primary Partition Create Extended Partition Create Logical Partition Activate Primary Partition Format all partitions.

Terminology Introduction:

The primary partition refers to the main partition of a hard disk, that is, the hard disk partition that contains the files and data necessary for the operating system to boot, and the hard disk must have a primary partition to install the operating system on the hard disk.

An extended partition is a partition other than the primary partition, but it cannot be used directly, and it must be divided into several logical partitions.

Logical partitions are the d, e, and f disks that we usually see in operating systems.

Partition format: "Formatting is equivalent to marking a grid on a white paper", and this partition format is just like the style of this "grid", different operating systems play "grid" in different ways, the partition format used by Windows is mainly FAT16, FAT32, NTFS, and almost all operating systems support FAT16. However, the actual utilization efficiency of hard disks using FAT16 partition format is low, so this partition format is rarely used nowadays.

FAT32 uses a 32-bit file allocation table, which greatly enhances its ability to manage disks, and it is currently the most used. Partition format, Win98 Me 2000 XP supports it. In general, when partitioning, King recommends that you set all partitions to FAT32 format, so as to get the maximum compatibility.

The advantage of NTFS is that it is extremely safe and stable. However, except for Winnt 2000 XP, other operating systems do not recognize this partition format, so you can't see the partition with this format in DOS and Win9X.

There are 3 types of hard disk partitions, namely primary partitions, non-DOS partitions, and extended partitions.

1. Primary partition.

The primary partition is a relatively simple partition, usually located in the front area of the hard disk, forming a logical C disk. The main bootloader is part of it, and this section of the program is mainly used to check the correctness of the hard disk partition, and determine the active partition, which is responsible for handing over the boot power to the DOS or other operating system of the active partition. If this program is corrupted, it will not boot from the hard disk, but it will be able to read and write to the hard disk after booting from a floppy drive or optical drive.

2. Non-DOS partitions.

In the hard disk, the non-DOS partition is a special form of partitioning, which is to divide a piece of the hard disk separately for another operating system, and for the operating system of the main partition, it is a piece of storage space that is divided. Only non-DOS partitioned operating systems can manage and use this storage area.

3. Extend the partition.

The concept of extended partition is relatively complex, and it is easy to confuse hard disk partition with logical disk. The fourth byte of the partition table is the partition type value, and the normal bootable basic DOS partition value greater than 32MB is 06, and the extended DOS partition value is 05. If you change the basic DOS partition type to 05, the system cannot be started and the data in it cannot be read or written.

If you change 06 to a type that is not recognized by DOS, such as EFH, DOS thinks that the partition is not a DOS partition and cannot be read or written. Many people use this type of value to implement the encryption technology of a single partition, and restore the original correct type value to restore the partition to normal.