I m going to take the DJI Phantom 4 on the plane, but I don t know if I can successfully board it

Yes, just like the camera computer, the battery should be taken out, and you can go through the security check normally. Batteries cannot be checked in, and no more than 3 batteries can be carried through the security check (including the fuselage). Customs generally does not check it. Links to relevant reference materials.

Generally speaking, yes, but the battery should be noted, due to the differences between airlines and countries for passengers to carry lithium batteries to the cabin, it is recommended to check with the specific airline and the competent authority of the reference flight destination.

The DJI aircraft is in a non-prohibited zone and has a maximum flight altitude.

for 500 meters.

The remote control distance of the equipment is different in different radio systems, and the following table lists the maximum flight distance and altitude of each model of the Phantom series for you

The maximum flight distance depends on the strength and stability of the video transmission signal, so please be sure to keep the aircraft in the best communication range.

The certification standards of the aircraft cannot be changed, and the aircraft will comprehensively judge the country and region based on the mobile device and the GPS of the aircraft.

Then switch to a standard that complies with local regulations.

Preparation steps before DJI Phantom 4 takes off:

Check that the remote controller, Intelligent Flight Battery, and mobile device are fully charged before takeoff.

Whether the propellers are installed correctly.

Make sure a micro-SD card is inserted.

Whether the camera and gimbal work normally after the power is turned on.

Calibrate the compass after powering on and check if the motor starts normally.

Whether the surrounding environment meets the flight conditions (it is recommended to be in an open field, avoid tall buildings, crowds).

The top switches of the Phantom 4 remote control are S1 and S2.

The S1 switch can be switched between three different flight modes: P mode (positioning), A mode (attitude), and F mode (function). Refer to the owner's manual for more details on airplane mode. It is recommended that novices turn the S1 switch to the top when controlling the aircraft, that is, select P mode (positioning).

The S2 switch triggers the Smart Home Switch, and flipping the S2 switch up and down once in flight allows the aircraft to return to the home point and land automatically.

The Phantom 4 is powered by DJI's next-generation flight controller, which supports the following flight modes:

P Mode (Positioning): Uses the GPS module to achieve precise hovering of the aircraft. According to the GPS signal reception strength, P mode.

Dynamically switch between the following states:

P-GPS: GPS satellite signal is good, GPS module is used for precise hovering.

P-ATTI: GPS satellite signal is not good, and does not meet the positioning conditions, only provides attitude stabilization.

A mode (attitude): does not use the GPS module for positioning, only provides attitude stabilization, if the GPS satellite signal is good, it can realize the return home.

f Mode (Function): Accessibility mode, please refer to the appendix for details on how to set the function.

The airplane mode is locked to P mode by default, if you need to switch to other airplane mode. Users need to go to the "Advanced Settings" page in the "Camera" interface of the DJI Go app and enable the "Allow Airplane Mode Switching" function.

In the DJI Phantom 4's mobile app, the aircraft function can be found by following these steps:1Open the DJI Phantom 4 mobile app.

2.Connect your remote control reciprocator to the aircraft. 3.

From the app's home page, tap the "Fly" button in the top right corner of the screen. 4.Once you're on the flight interface, you'll be able to see different aircraft function buttons, including:

Fly Spine World Rest Mode, Take-off and Landing, Return Home, Automatic Flight, Manual Flight, etc. 5.Click on the function button you need and follow the prompts.

It should be noted that different aircraft models and versions may have slightly different operation interfaces and function settings, but in general, aircraft functions can be found in the flight interface. Make sure that you have connected the aircraft and the remote controller, and that the app is properly connected to the aircraft in order to use the aircraft functions correctly. 

Hello, we are glad to answer for you: The "Find Plane" feature of DJI Cave Phantom 4 can be found in the DJI GO 4 app. The specific steps are as follows:

1.Open the DJI GO 4 app and connect your remote control and drone. 2.

Tap on the "Flight Recording" button at the bottom right of the app. 3.In the Flight History page, select the flight record you want to find, and then click the "Aircraft" icon.

4.Click on the "Find Plane" button and the app will show the last location of the drone on a map and provide some information about the aircraft. Please note that in order to use the "Find Plane" feature, you will need to turn on the drone's GPS location function during the flight and make sure that the app has sufficient permission for the visitor to ask for your device's location information.

Also, this feature is only available for aircraft that you have already flown and may not be available if your drone has never taken off or is offline.

You can also start the motor by performing the lever breaking action (inner eight: the left rod is broken to the lower right corner, and the right rod is broken to the lower left corner), and after the motor starts, please release the remote lever immediately.

When the aircraft lands, pull the throttle stick to the lowest position and hold it for a few seconds before the motor stops.

Indoor take-off to turn off the novice mode. In order to take off in two strokes within eight dozen.

After opening DJI GO and connecting to Phantom 4, there will be a prompt if it is not activated, just follow the steps to activate.