How to paste the tempered film every time there are bubbles, and what to do if there are bubbles aft

Updated on number 2024-03-10
9 answers
  1. Anonymous users2024-02-06

    Since the bubbles of the tempered film are mostly caused by the residual dust on the screen, it is impossible for the bubbles of the tempered film to disappear by themselves under normal circumstances. If the air bubbles under the film are large, it will affect the use, and if it cannot be removed, the film can be re-applied.

    If you can't push it out, you can only uncover and repost. There is also a case of white edges, which is a problem with the phone itself, and this can be purchased with white edge filler. In what case, it is recommended to consult the seller to avoid waste.

    Will the tempered film bubbles disappear on their own3

    When we paste the bubbles left by the tempered film can not get out, in addition to the quality of the tempered film itself, in addition to the tempered film fit is not enough and the mobile phone screen is not cleaned is also an important cause, the tempered film is different from the general film, it is electrostatic bonding, and the hole is aligned.

    1. Hard card processing.

    If there are air bubbles in the tempered film, first use a hard card to pry open the corner close to the bubble, and the bubbles will disappear after full contact with the air. Then use the bank card to press the unopened tempered film part and slowly press the tempered film forward, so that the pried part is in full contact with the mobile phone screen and is tightly bonded. Finally, use the bank card to scrape the phone screen back and forth several times to make the tempered film look flat and bubble-free.

    2. Hair dryer treatment method.

    First turn on the power of the hair dryer, turn on the hot air gear of the hair dryer, blow on the mobile phone screen, after the screen softens, immediately turn off the hair dryer, and then press the bubbles in the tempered film with your fingers, after pressing for a period of time, the bubbles will disappear. It should be noted that when using a hair dryer, you must control the time well to avoid damage to the mobile phone screen if the temperature is too high.

    3. Lubricating fluid treatment method.

    First, use a toothpick to dip an appropriate amount of lubricating liquid, and then pry open the corner of the mobile phone screen close to the bubble, so that the lubricant on the toothpick is in direct contact with the bubbles.

  2. Anonymous users2024-02-05

    To eliminate the bubbles of the mobile phone tempered film, the materials that need to be prepared include: cards and transparent glue. 1. First of all, you can use a card to scrape off the bubbles, as shown.

    2. Then, so that the bubbles are eliminated as shown below. 3. Then, if there is blistering that cannot be pushed off, it is because bubbles have formed inside the film, and you can stick transparent glue on the film, as shown below. 4. Then, gently pull the transparent glue and pull up one side of the film as shown below.

    5. Finally, use another piece of transparent glue with the other hand to stick the dust off, as shown below. Precautions: 1. If you buy a non-customized film, you need to prepare scissors, rulers, pens, and non-woven fabrics, and cut the film and equipment on a flat desktop to fit the device screen.

    Cutting should be fast, accurate, and a success, so that it is beautiful. 2. If you have purchased the original film that matches your own equipment model, you do not need to do it separately. Generally, when you go to a physical store to buy a mobile phone, the film is pasted, and friends who like online shopping buy a bare machine, and most of them have to do it yourself How to deal with the bubbles in the mobile phone film 1

    Scissors and scotch tape, and a small piece of cloth 2. Use a small piece of cloth to push away the air bubbles that can be squeezed out. Fold the cloth a few times and use its edges to push the bubbles. 3. There are still these bubbles that can't be pushed off.

    Why can't they be pushed off? Because there is dust, it is the dust that forms bubbles in it, and we have to take out the ash method to remove this bubble. 4. Cut the scotch tape one to two inches long and stick it next to the dust bubbles on the film, and then cut a small section of the scotch tape with the glue side up.

    5. At this time, use one hand to pull up the transparent tape attached to the film, and use it to pull up the film up a slit, as long as you pull a slit, you can let the tape in the other hand.

  3. Anonymous users2024-02-04

    You can use this small piece of cloth to push the bubbles on the screen first, so that the contact area between you and the entire screen becomes larger, and there will be no gaps when pushing to let the bubbles run away. You can also fold the cloth in half a few times when pushing, and then use its edge to push the bubbles.

    After pushing a few times, you will find that there will still be a few very fine bubbles on the mobile phone screen, and even if you push it a few more times, you will still find that this bubble will not be removed, that is, because this bubble has quite fine dust in it, which is a fine bubble formed by dust, so no matter how you push with a cloth, if you don't remove the dust inside, there will always be such bubbles. At this time, all we have to do is to remove the dust inside the bubble.

    At this time, you can use the tape, maybe you think of using the tape to stick the fine dust, in fact, this is the method, but we still need to do some skills when using. You can cut a piece of tape, and then stick it directly on the phone screen, and then pull up this piece of tape, and the stickiness of the tape can pull the film up the way. Only a small gap is needed, and then a small piece of tape is cut out, and the dust on the screen or film is directly glued off, so that the whole phone can become more clean and tidy very effectively, and finally the film is pasted on the mobile phone, and finally you can find that many of the original bubbles are basically gone.

  4. Anonymous users2024-02-03

    How to solve the problem of bubbles on the edge of the mobile phone tempered film.

    Method 1: We can fold a piece of hygiene into a thicker and softer square, and then aim at the bubbles to push and press out, give priority to the large bubbles in the process of pushing, and push the bubbles to the edge of the film. When handling small bubbles, try to push them out as close to the edge as possible.

    Method 2: Push the hard card next to the film with appropriate force, and give priority to the large bubbles in the process of pushing. When you push it to the edge of the film, you can let the bubbles dare to go out. When handling small bubbles, try to push them out as close to the edge as possible.

    Method 3: Sometimes the bubbles are often caused by dust in the film, so you can gently lift up the dusty side of the film, use transparent glue to wipe off the dust inside, and then gently put down the film. Then use toilet paper.

    Or just press the glasses cloth so that the film fits snugly against the screen, and we're done.

    The above is the specific operation method of how to solve the bubbles on the edge of the mobile phone tempered film, I believe that everyone can quickly learn how to operate and deal with it through the understanding of the above content.

  5. Anonymous users2024-02-02

    The tempered film generally does not have bubbles.

    If you can still do it next to it, if the bubble is in the middle, you will have to replace it from the beginning. The film application speed must be fast, otherwise there will be too much dust.

    If there are as many bubbles as there are in the normal membrane, I can clean them out.

  6. Anonymous users2024-02-01

    Reasons: 1. Tempered film quality problems.

    Second, in the normal use of the mobile phone, it is inevitable that there will be various pressures on the mobile phone screen, and the force is uneven in various places, and there will be bubbles for a long time.

    Method of pasting mobile phone tempered film:

    First, clean up the dust and oil stains on your hands first, and wash them with hand sanitizer.

    2. Wipe the surface of the mobile phone with a glasses cloth or a soft cloth that does not shed a small amount of water, and clean up the dust and fingerprints on the surface.

    3. Tear off one side of the protective film, then aim at the phone, align the top and left sides of the film and paste the film.

    Fourth, slip or when sticking the film, try to maintain a constant speed, and pull back less when bubbles appear to ensure that there are no bubbles on the surface of the film. Then use wool felt.

    Scrapers, or padded scrapers, to avoid scratches. Slowly press the film little by little on the surface of the phone, in this case, there will be few bubbles instantly.

    Fifth, after the paste, repair the bubbles in some areas. Wrap the credit card with a hard card, credit card, etc., with the soft cloth that just wiped the screen of the letter, and then slowly exert force to scrape the bubbles out of the edges.

    Introduction to tempered film:

    Tempered glass mobile phone film.

    It is a new mobile phone protective film launched in China in 2012, and it is currently the most powerful high-end new product to protect the screen.

    The thickness of this protective layer is only millimeters, and the high silver can completely cover the original screen surface, prevent damage and scratches by external forces, and increase the impact absorption, which is 5 times higher than the standard of PET film. It does not affect the effect of the screen.

  7. Anonymous users2024-01-31

    Pro-[warm] bubbles after pasting the tempered film is a relatively common situation, and the following methods can usually be tried:1Extrude bubbles:

    Use a card or fingernail to gently squeeze the edge of the bubble outward until the bubble is completely extruded. 2.Remove air bubbles:

    If the bubble is large or the squeeze cannot be solved, you can use a special bubble remover or similar gadget for the mobile phone screen protector to suck or squeeze out the bubble. 3.Wait for the bubbles to disappear:

    In some cases, small bubbles may disappear on their own within a few days or weeks without affecting use. Note: In the process of handling air bubbles, avoid using sharp objects to cut the surface of the tempered film to avoid scratches and damage.

    At the same time, it is recommended that Mengyin clean the mobile phone screen before the film to ensure that there are no impurities such as dust and grease on its surface, so as not to affect the effect of the film.

  8. Anonymous users2024-01-30

    There are air bubbles in the tempered film, which can be removed with the help of tools such as scrapers, and the operation method is as follows

    Tools: scraper, tempered film.

    1. Pick open the gaps.

    Find the corner of the newly applied tempered film and pick it open with your hand.

    2. Use a scraper to scrape out air bubbles.

    After lifting a slit, use a scraper to start scraping close to the bubbles.

    3. Compress the tempered film.

    After scraping out the bubbles, re-press the edges of the tempered film by hand.

    Precautions for pasting tempered film1. Pay attention to wipe the screen with your own film. If you want to apply the film yourself, pay attention to wipe the screen clean, this is very important, generally there will be a wiping cloth in the film, and you must thoroughly wipe the fingerprints and dust on the screen.

    2. When sticking the film, pay attention to the uniform pasting, and try not to produce bubbles, otherwise it is easy to enter the air and dust, and you can't see the patterns and subtitles on the screen clearly, which is easy to cause visual fatigue. If you can't stick it yourself, it's best to go to a professional store to find someone to apply the film.

  9. Anonymous users2024-01-29

    The treatment method of the tempered film with bubbles is as follows:

    1. With the help of a hard card: first use a hard card or bank card to pry open the corner close to the bubble, and the bubble will disappear after full contact with the air. Then use the bank card to press the unopened tempered film and slowly press the tempered film forward, so that the opened part can also be in contact with the mobile phone screen and glued together.

    Finally, gently scrape the phone screen with a bank card to make it look neat and comfortable. The advantage is that it is simple and the tools are easy to find. The disadvantage is that it is easy to scratch the tempered film.

    2. With the help of the hair dryer key: use the heat of the hair dryer to soften the tempered film, blow the bubbles with hot air for a period of time, and then press and hold the bubbles for a period of time, repeatedly, so that the tempered film is easier to fit the mobile phone screen. The advantage is that the bubbles are easy to remove when they are in the middle of the screen.

    Disadvantages: It is not easy to grasp the time and heat of blowing, and it is easy to damage the screen.

    3. With the help of a clip: find a clip with a relatively large clamping force, before going to bed at night, clamp the bubble at the edge of the mobile phone screen, clip it overnight, and get up the next morning, surprised to find that the bubble is gone! The advantage is that it is simple, and the tools are easy to find and buy.

    The disadvantage is that if you accidentally slip the clip, the edge of the phone will be scratched by the iron edge of the clip, so you accidentally damage the paint of the phone.

    The biggest role of the tempered film is to protect the glass of the mobile phone screen, because the current mobile phones are full lamination technology, so the glass damage replacement needs to replace the entire screen, compared with a mobile phone film is much higher, and the anti-collision performance of the plastic film is not as good as the tempered film.

Related questions
8 answers2024-03-10

Nowadays, smartphones are becoming more and more popular, and the products related to them are becoming more and more abundant, and the screen tempered glass film is one of them. Tempered glass film is now getting cheaper and cheaper, so that many people like to buy it online and do it themselves, and paste it on their beloved mobile phone to prevent the screen from being scratched or accidentally shattered. >>>More

5 answers2024-03-10

Flat tempered film: It is the kind of cabbage price tempered film that we commonly use **9 pieces of 9 free shipping, there is no problem in workmanship, it is a very ordinary tempered film, with an electrostatic adsorption coating, if your mobile phone is an ordinary flat screen mobile phone, you can choose a tempered film at will, in fact, the scientific and technological content of the tempered film is not high, and the electrostatic adsorption coating is basically used for 1 2 years without a problem, and it will not fall off. >>>More

7 answers2024-03-10

Reason: Generally, when you go to a physical store to buy a mobile phone, the film is pasted, and friends who like to shop online buy it are bare metals, and most of them have to apply the film yourself. >>>More

7 answers2024-03-10

From the perspective of protecting the mobile phone screen, the tempered glass film is better, and when the mobile phone is dropped, the impact resistance effect is better, and the screen is not easy to break. >>>More

17 answers2024-03-10

Most of the small bubbles disappear when sunburned. Car wrapsAfter there are bubbles that will disappear automatically. >>>More