How to paste tempered film on the mobile phone screen, how to paste the tempered film on the mobile

Nowadays, smartphones are becoming more and more popular, and the products related to them are becoming more and more abundant, and the screen tempered glass film is one of them. Tempered glass film is now getting cheaper and cheaper, so that many people like to buy it online and do it themselves, and paste it on their beloved mobile phone to prevent the screen from being scratched or accidentally shattered.

Today we will teach you some tips for applying film.

First. After the tempered glass film is bought, it generally has all the tools required for the film, such as dust-free cloth, alcohol wiping bag, and dust sticker.

Second. When tearing off the tempered film on the original screen, you need to operate slowly, because the tempered film has been pasted on the screen for a while, and the adhesion between some tempered films and the screen will be very large.

Third. After the mobile phone film is used for a period of time, there will be obvious dirt on the surface of the screen, at this time, you can first wipe the screen with a wiping cloth (wet cloth), and then use a dust-free cloth, and finally if there are still water stains left, you can wipe it again with a wiping bag (dry cloth).

Fourth, after the above cleaning, the screen is generally relatively clean, but there may also be some small dust, at this time, you can use a sticky dust paste to paste the surface of the screen again, so that it is very clean.

Fifth. Take out the tempered film, the tempered film generally only has the No. 1 label, and tear off the protective film of the No. 1 label.

Sixth. Hold the torn side facing the screen, align it with the hole, and gently lower it.

Seventh. After the tempered film is put down, two situations may occur.

1. The tempered film has not yet been attached to the screen, and the tempered film floats on the screen, at this time, if the hole position is not accurate, you can fine-tune it, and use your mobile phone to gently push the edge of the tempered film, and you can adjust the position. After adjusting the position, press your finger to the middle of the screen, and the tempered film will automatically adsorb on the screen.

2. The tempered film quickly starts to be automatically adsorbed from the edge.

Eighth. After the tempered glass film automatically adsorbs the screen, there may be some small bubbles, at this time, you can use a dust-free cloth to gently wipe back and forth a few times to press down these small bubbles, and you're done!

But there are a few things to keep in mind:

1 Before applying the film, you need to prepare a quiet environment with relatively stable air. Do not blow the fan or air conditioner to avoid excessive dust during the film application process and reduce the workload.

2 If the tempered film is crooked, you can slowly tear the tempered film up and realign it again.

3 If you find dust after pasting, pay attention to whether the dust is on the tempered film or on the screen when tearing it up, and use a sticky dust sticker to stick the dust away.

4. The production of tempered film needs to be carried out in a dust-free workshop, so the tempered film is not suitable for washing or anything, and it is easy to scrap the whole tempered film!

You can go to the repair shop and see how people put it up.

First of all, prepare the items to be used for the film, such as mobile phones, vacuum cleaning film, and wet and dry wipes.

Then remove the old tempered film from the phone, being careful not to damage the phone screen.

Then find the vacuum film and use the vacuum film to stick the dust off the phone little by little.

Then wipe the phone screen with a wet wipe, and the dirty things on the phone screen will dissolve on the wipes.

Take out the new tempered film and slowly apply it from top to bottom to the speaker until it fits perfectly.

After completing the above settings, you can attach the tempered film to the phone.

Tools and materials needed: mobile phone, tempered film set, clean water.

1. Clean your hands first to keep them clean.

2. After putting the mobile phone flat, the person should try to stay away from the position of the mobile phone, and gently buckle the corner of the tempered film with a fingernail along the edge of the mobile phone.

3. When the corner of the tempered film is lifted, the tempered film can be broken down along the direction of the paste.

4. Before pasting the new film, please wipe the mobile phone screen with an alcohol cotton and wipe off the excess alcohol on the screen with a dust-free cloth.

5. Use a dust suction film to suck off small dust that is not easy to wipe off.

6. Tear off the protective layer of the new film and stick it on the opening position of the mobile phone screen.

7. Gently squeeze to complete the film.

Wipe the mobile phone screen, take out the dry cloth, wipe the residual alcohol on the screen, tear the tempered film, align the mobile phone screen, start aligning from the earpiece, pay attention to the alignment around the earpiece, place it, press the middle part of the screen with your fingers, the tempered film will be automatically adsorbed, spread around, lift the tempered film at the corner, and squeeze out the bubbles with your thumb.

Mobile phones, tempered film.

01 First of all, we disassemble the tempered film we bought, and then check whether the items that need to be used are enough. Among them, we include tempered film, alcohol paper, small handkerchief, white edge filler, and dust removal sticker.

02 The first step is to unpack the alcohol paper and then wipe our screen.

03 Then after confirming that the entire screen is clean, we choose to use a small handkerchief to wipe off the excess water on the screen.

04 Then use the dust removal sticker to glue off the remaining gray stains on the screen, so as to avoid the residual dirt after we put the tempered film, which will affect the appearance.

05 At this time, we will gently place the tempered film along the screen, flat or slowly put it down from the side.

06 Then put the phone upright so that the bubbles can be easily discharged.

07 After that, wipe the surface of the tempered film with the remaining alcohol paper to help the air bubbles expel out.

08 Then remember to take out the white edge filler we prepared at this time, fill the white edge around the outer perimeter of the mobile phone tempered film, and apply it along the periphery anyway, of course, to confirm that our liquid has gone in.

09 Finally, we wiped the tempered film clean and pasted it.

If there is a white edge filler, it is used, which can prevent dust from entering the tempered film.

The tutorial of sticking tempered film on mobile phones is as follows:Tools: mobile phones, tempered films.

1. Tear off the film on your old phone.

2. Use a clean cloth to clean the dust off your phone.

3. Tear off the A side of the tempered film.

4. Paste the joint of the tempered film to the edge of the mobile phone.

5. Use the card to slowly close the tempered film to the mobile phone screen.

6. After pasting the film, if you find that there are bubbles, use the card to slowly drive out the bubbles.

7. If there are no bubbles, tear off the B side of the tempered film. When you tear off the B-side in advance to catch up with the bubbles, you will blur the screen.

The steps of how to paste the toughened film of the mobile phone are as follows:

Material preparation: tempered film, vivo Y67, etc.

1. Wipe the phone clean first, there can be no small dander on the screen, and then we prepare a new tempered film.

2. Tear off the protective layer of the new tempered film, and then check whether there is ash on the phone, and wipe it off if there is ash.

3. Then paste the tempered film on the mobile phone, and pay attention to the eyes on the mobile phone when pasting the tempered film.

4. After the tempered film is placed on the phone, press and hold the middle with your hand, and the air will automatically run out to both sides, and then press it with your hand.

What you need to know about taking care of your phone

1. Don't wait until the battery level of the mobile phone starts to alarm and shows that it is out of power before charging the phone. Generally, when the battery is only about 30%, it is time to charge the phone.

2. When charging your phone, don't overfill it. Don't rush too long, either. As long as the phone shows that it is full, or rushes to about 90 percent, it can stop charging.

3. Mobile phones are all lithium batteries. Lithium batteries are afraid of heat and are usually exposed to direct sunlight. It is also best to keep away from heat sources. When charging your phone again, don't charge it while playing with it.

4. Try to choose the original charger, do not often mix chargers, which will not only hurt the battery of the mobile phone, but also reduce the service life of the battery. And it's easy to cause**.

5. Smartphones have more functions. It is very convenient to use, but relatively, the power consumption is also relatively large, so there is no useful software, or the function should be turned off in time.

5. Smartphones have more functions. It is very convenient to use, but relatively, the power consumption is also relatively large, so there is no useful software, or the function should be turned off in time.