Can the ant protection board be set to factory reset?

Protection Plate Calibration:

1.Single voltage calibration: You can change the cell voltage value by adjusting the "system reference voltage" (the default left and right), and slowly increasing and decreasing the amplitude until it is accurate!

2.Total voltage calibration: You can change the total voltage by adjusting the "parameter of converting the total voltage AD value to the actual voltage" (about 3330 by default), and slowly adjust the size of this value until it is accurate!

3.Current calibration: You can adjust the "current sensor range" and slowly adjust the magnitude of this value to change the current until it is accurate!

Note: Please do not change the "Power Starting Current" item in the parameter settings, too much may cause the discharge MOS tube to be burned!!

There are three ways to reset: reset recovery (can only be reset within 2 minutes to 10 minutes after the miner is turned on, otherwise it will be unsuccessful) After powering off and restarting for 2 minutes, press and hold the "reset" button for 5 seconds, and then release it, the miner will restore the factory settings and automatically restart within 4 minutes (no need to power off the miner).

Tool raw materials computer mining machine.

Method: Read step by step.

reset (can only be reset within 2 minutes to 10 minutes after the miner is turned on, otherwise it will not be successful).

After 2 minutes of power failure and restart, press and hold the "reset" button for 5 seconds, then release it, and the miner will restore the factory settings and automatically restart within 4 minutes (no need to power off the miner).

Restore with a web page in the background interface.

Click Upgrade - Perform Reset and click "OK" in the pop-up dialog box.

IPRortale button factory reset (currently only applicable to S9, T9).

How to use: Power off the miner, press and hold ipreporte without releasing it, and at the same time power on the miner, release it after powering on for 5 seconds, and the miner will automatically restore to the firmware when it leaves the factory.

Summary. Hello, boot management can activate the ant protection board standby mode operation, if the ant protection bar has been thinking, you can temporarily turn off the power first, or turn off its switch, see if you can make this want to stop, and then start again and try again.

Hello, boot management can activate the ant protection board standby mode operation, if the ant protection bar has been blindly thinking, you can temporarily turn off the power brother jujube, or turn off the switch to remove it, see if you can stop this kind of thinking, and then start it again and try again.

Hello, boot management can activate the ant protection board standby mode operation, if the ant protection bar has been blindly thinking, you can temporarily turn off the power brother jujube, or turn off the switch to remove it, see if you can stop this kind of thinking, and then start it again and try again.

P+, P- output. B+ is connected to the positive pole of the cell, and B- is connected to the negative pole. If the shouting is multi-segment series, the negative electrode of B1 and the positive electrode of B2 are connected together, and the negative electrode of the last battery is connected to BN-.

Solder the wire first, then connect the battery, don't connect it wrong. If there is no output after completion, remember to use the charger to charge and activate on the charging port of P+ and P-lead. Filial piety.

But I've shut down the system.

You can open it.

How to solve it now, Bluetooth can't be connected, and the two small wires are still the same.

P+, P- output. B+ is connected to the positive pole of the cell, and B- is connected to the negative pole. If the shouting is multi-segment series, the negative electrode of B1 and the positive electrode of B2 are connected together, and the negative electrode of the last battery is connected to BN-.

Solder the wire first, then connect the battery, don't connect it wrong. If there is no output after completion, remember to use the charger to charge and activate on the charging port of P+ and P-lead. Filial piety.

Won't wow. <>

This is the easiest way to do it.

Hard. <>

Kiss or find a friend Generally boys understand.

Hello, glad to answer for you. According to the above situation: the ant protection board can't be adjusted how to restore the factory settings.

A: If your ant protection board won't adjust and you need to restore it to factory settings, you can try the following steps:1

First of all, turn on the power switch of the ant protection board, and wait for it to fully start. 2.After waiting for all the lights on the panel to turn off, using a thin-tipped needle or other similar tool, press and hold the "Reset" button on the panel until the lights on the panel start flashing.

3.As soon as the light on the panel starts flashing, release the "Reset" button. Your ant protection plate has now been restored to factory settings.

4.If your ant protection board is connected to the network, you will need to reconfigure its network settings. In this case, please note that a factory reset will erase all the configuration data saved on the Ant Protection Board, so make sure you want to do a factory reset and make a backup.

In a word, you can restore the ant protection board to factory settings by long-pressing the "reset" button, but please note that before proceeding with this step, please back up your data to avoid data loss.

Summary. No password is required, and the ant protection board only needs to press the restart button to restart. If the restart fails, you can try the following:

1.Check if the power supply is normal, if not, replace the power supply or check if the power cord is not in bad contact. 2.

Check if the power button of the ant protection board is normal, if not, replace the power button. 3.Check if the circuit board of the ant protection board is damaged, and if there is damage, replace the circuit board.

4.Check whether the software of the ant protection board is normal, if not, please reinstall the software. 5.

Check whether the hardware of the ant protection board is normal, if not, please replace the hardware. The above are the solutions and practical steps for restarting the ant protection board, I hope it can help you.

No password is required, and the ant protection board only needs to press the restart button to restart. If the restart fails, you can try the following:1

Check if the power supply is normal, if not, please replace the power supply or check if the power cord is not in good contact. 2.Check whether the power button of the ant protection board is normal, if not, please replace the power button.

3.Check whether the circuit board of the ant protection board is damaged, and if there is damage, please replace the circuit board. 4.

Check whether the software of the ant protection board is normal, if not, please reinstall the software. 5.Check whether the hardware of the ant protection board is normal, if not, please replace the hardware.

The above are the solutions and practical steps for restarting the ant protection board, I hope it can help you.

Can you elaborate on that a little bit more?

In response to the problem, the restart of the ant protection board does not require a password. Ant Protection Board is a professional security protection device, which can effectively prevent network attacks and protect network security. Its restart operation is very simple, you just need to press the restart button, and you don't need to enter any password.

In addition, the Ant Protection Board has many other functions, such as detecting network attacks, blocking malicious network traffic, preventing network attacks, protecting network security, detecting network vulnerabilities, and providing security policies. It can also provide security policies, such as restricting network traffic, restricting network access, restricting network limb applications, etc., to protect network security. In short, the ant protection board is a very practical security protection device, it can effectively prevent network attacks, protect the network security, and the restart operation is very simple, no need to enter any password.

Summary. Yes, the ant protection board reboot requires a password to operate.

Yes, the ant protection board reboot requires a password to operate.

Can you add, I don't quite understand it.

If the ant protection board is affected by normal operation and needs to be restarted, it usually does not require a password. However, if a prompt "Please enter the administrator password" appears on the screen when restarting, you will need to enter the correct administrator password to restart. If you have forgotten your administrator password, you can try to reset it by following the procedures in the user manual.

It should be noted that resetting the password will erase all the data in the ant protection board, so a backup is required before proceeding. When using the ant protection board, it is recommended to strictly let Xiangge operate according to the operation manual to avoid unnecessary trouble caused by operation errors.