Various types of bucket teeth of excavators, what materials are used for excavator digging bucket to

Suitable for all types of excavator buckets:

1. Light bucket.

Suitable for excavating low-impact, low-wear materials (e.g. dirt, loam, clay).

The shallower bucket profile makes it easy to dump the clay.

The lightweight construction reduces loading time and increases lifting force.

Reserved for borehole side strength plate can be optionally equipped with a side shovel.

2. A general-purpose bucket.

Suitable for excavation of low-impact, moderately abrasive materials (e.g. dirt, sub-clay, gravel and clay).

The shallower bucket profile makes it easy to dump the clay.

The lighter construction reduces loading time and increases lifting force.

Reserved for borehole side strength plate can be optionally equipped with a side shovel.

3. Heavy-duty bucket.

For abrasive applications (e.g. concrete, clay and stone).

Thicker bottom and side wear plates improve wear resistance.

Stronger construction than general purpose buckets.

Reserved for borehole side strength plate can be optionally equipped with a side shovel.

4. Heavy duty rock bucket.

Suitable for demanding loading in high-wear applications (e.g. crushed stone, granite).

The thickest wear plate to extend bucket life in harsh applications.

Stronger construction than a heavy gravity bucket.

The side wear guards extend further into the upper part of the bucket to provide maximum bucket protection in the rock.

Excavator bucket teeth:

Lightweight teeth – for most applications.

Long teeth – for most applications.

Wide bucket teeth – used to clear the ground. The capacity is increased and the overflow is small.

Heavy-duty long buckets – mounted on large machines for general loading and excavation operations. It has a long wear life and higher strength.

Short bucket – for high impact and prying out operations (e.g. stone). Super strong and sturdy.

Heavy-duty abrasion bucket – Mounted on large machines for sand, gravel and gravel operations.

Penetrating teeth – for dense compaction materials (e.g. clay). Provides enhanced penetration.

Self-sharpening twin tip bucket – used to increase crushing capacity. Worse penetration than the sharp teeth. Wear resistance than the pointed teeth.

Enhanced Penetration Bucket – for materials that are not easily penetrated under high impact conditions (e.g. sedimentary rocks).

cemented gravel or crushed stone with a large degree of lump).

Models are distinguished by machines, according to different brands, and then according to the size of the model, such as PC200, PC300, EX200, SY65 and so on... The bucket is the same, the model is different for different models. According to the construction site, the bucket is divided into earthwork bucket, rock bucket, sand digging bucket, etc., and the bucket teeth are the same.

If you want to go to the first business, you can go to the Internet to find, Zhejiang Ningbo, Ningdong, Wanguan, etc., Jiangxi Nante, Yinhui, Xinxing, etc., there are many factories that produce this.

1.Standard bucket.

Standard digging bucket is also called earthwork bucket, is a common digging bucket, generally small and medium-sized excavators are equipped with this standard digging bucket, suitable for clay, sand and other earthwork excavation and loading operations, its bucket capacity is larger, the bucket mouth area is large, the filling coefficient is high, and the standard plate thickness is used at the same time, there is no reinforcement and thickening, the production cost is low, and the overall cost performance is higher.

2.Strengthen the bucket.

On the basis of the original standard bucket, the reinforced bucket is reinforced with high-strength wear-resistant steel materials for high-stress and easy-to-wear parts, which greatly improves the strength and wear resistance of the bucket, and is suitable for excavating hard soil, gravel, gravel, etc.

3.Rock digging buckets.

As the name suggests, excavators equipped with rock buckets are suitable for excavation and loading of rocks, sub-solid stones, weathered stones, solid rocks and ore after blasting, and are widely used in harsh environments such as mines and quarries. The whole bucket is made of thickened plates, the bottom is added with a reinforcement plate, and the side guard plate is added to the side, so that the strength and wear resistance are further enhanced.

4.Mud buckets. The mud bucket is also called the dredging bucket, and the difference with the above-mentioned digging bucket is that it has no bucket teeth, the width is larger, and it is suitable for the plane trimming of slopes and steep slopes, and it is also suitable for cleaning the silt of the ditch and river.

5.Loosening bucket.

The teeth of the loosening bucket are very sharp, generally three teeth, easy to break the soil, and take into account the excavation and loading function in the case of loosening effect, which is suitable for loosening, excavation and loading operations on frozen soil, hard soil, stone ore and other geology, especially suitable for pipeline laying narrow ditch operations.

It is distinguished by the number of teeth.

Hello, the excavator digging bucket tooth plate is generally used for wear-resistant steel plates. There is also high hardness wear-resistant steel according to the use environment. Introduction of high-hardness wear-resistant steel excerpted from French steel High-hardness wear-resistant steel is widely used in mining machinery, coal mining and transportation, construction machinery, agricultural machinery, building materials, electric power, railway transportation and other departments.

For example, the steel balls and liners of ball mills, the bucket teeth and buckets of digging and shelving machines, and the rolling walls, tooth plates, hammer heads of various crushers, etc.

The teeth are ductile iron.

Detailed introduction: According to the environmental classification of the use of excavator bucket teeth. Excavator bucket teeth can be divided into rock teeth (used in iron ore, stone mines, etc.), earthwork teeth (used for digging soil, sand, etc.), and conical teeth (used in coal mines).

According to the bucket tooth holder, the excavator tooth can be divided into vertical pin tooth (mainly Hitachi excavator), horizontal pin tooth (Komatsu excavator, Carter excavator, Daewoo excavator, Kobelco excavator, etc.), rotary digging bucket tooth (V series bucket tooth).

1. The bucket teeth are ductile iron, the tooth emperor is cast steel, the gum is manganese steel plate, the angle knife is also manganese steel, and the main material of the bucket teeth is the general ship steel plate. The ears that attach the forearm are cast steel.

2. A brief introduction to the bucket teeth of the excavator: the bucket teeth of the excavator are important consumable parts on the excavator, similar to the human teeth, which are a combination of tooth base and tooth tip, and the two are connected by pins. Since the tooth wear failure part is the tooth tip, as long as the tip is replaced.

3. According to the environmental classification of the use of excavator bucket teeth. Excavator bucket teeth can be divided into rock teeth for iron ore, stone mines, etc., earthwork teeth for digging soil, sand and rocks, etc., and conical teeth for coal mines. According to the state cavity bucket tooth holder to divide:

Excavator bucket teeth can be divided into vertical pin bucket teeth, horizontal pin bucket teeth, rotary digging bucket teeth.

The size of the excavator bucket is based on the capacity of the bucket to carry out the quantification of the model, the general bucket capacity is different, and the size of the bucket has a great relationship, such as the width, height and depth of the bucket capacity, etc., are one of the criteria for determining the size of the bucket.

The bucket can be divided into material type and functional products, and the application amount of the general material type bucket is still relatively large, which can meet the needs of different construction fields for products, such as the bucket for river cleaning, the bucket for hard stone and soft soil operations, and the hard stone operation'Buckets, these buckets are relatively high-quality buckets, with good corrosion resistance and bending resistance.

Generally, according to the different fields and places of bucket application, it can be divided into standard bucket and reinforced bucket, and the demand for rock bucket is also relatively large, and this type of bucket can be used in trench excavation, municipal cleaning, agriculture and forestry operations.

The main device on the excavator is the bucket, which is a kind of working device on the hook machine, and in the process of carrying out the construction and operation of the excavator, the demand for the bucket is still relatively large, and the performance requirements are relatively high.

First, the size standard of the excavator

The size of the excavator bucket is based on the capacity of the bucket to carry out the quantification of the model, the general bucket capacity is different, and the size of the bucket has a great relationship, such as the width, height and depth of the bucket capacity, etc., are one of the criteria for determining the size of the bucket.

The bucket can be divided into material type and functional products, the application amount of general material type bucket is relatively large, which can meet the needs of different construction fields for products, such as the bucket for river cleaning, the bucket for hard stone soft soil operations, and the bucket for hard stone operations, these buckets are relatively high-quality buckets, with good corrosion resistance and bending resistance.

Generally, according to the different fields and places of bucket application, it can be divided into standard bucket and reinforced bucket, and the demand for rock bucket is also relatively large, and this type of bucket can be used in trench excavation, municipal cleaning, agriculture and forestry operations.

The main device on the excavator is the bucket, which is a kind of working device on the hook machine, and in the process of carrying out the construction and operation of the excavator, the demand for the bucket is still relatively large, and the performance requirements are relatively high.

Second, the size of the backhoe excavator

Hoisting operations can be carried out, and the specification requires that bucket hooks need to be installed, and it is not allowed to hoist Komatsu with bucket teeth, and the machine has an L mode specifically for hoisting operations.

The materials excavated by the excavator are mainly soil, coal, sediment, and soil and rock after pre-loosening. The three most important parameters of the excavator are: operating weight (mass), engine power and hopper capacity.

Classify. According to the different sizes, excavators can be divided into large excavators, medium excavators and small excavators.

According to the different ways of walking, excavators can be divided into crawler excavators and wheeled excavators.

According to the different transmission methods, excavators can be divided into hydraulic excavators and mechanical excavators. Mechanical excavators are mainly used in some large mines.

According to the use, excavators can be divided into different categories such as general excavators, mining excavators, marine excavators, and special excavators.