How to disassemble the faucet, how to disassemble the faucet

You can spray the fastened bolts of the faucet with a rust remover to make the bolts moisturized and easy to disassemble.

You can use an open-end wrench to disassemble the fastening place of the faucet, which can achieve the purpose of unfastening.

If the open-end wrench cannot be unscrewed, you can try to unscrew it with a pipe wrench, which can be sprayed with rust remover, which can achieve better results.

If you really can't unscrew the position of the faucet connector, you can try to unscrew the section of the faucet that comes with the interface pipe.

a. Preparation.

If you don't want to waste too much water during disassembly, it's important to remember to close all the valves before you start removing the faucet. The operation method is very simple, after tightening the upper angle valve, find a larger basin and put it under the water pipe to prevent water seepage because it is not closed tightly.

b. Start dismantling.

Generally speaking, after completing the previous step, there will be some water left in the water pipe, so the specific dismantling process of how to disassemble the faucet is to separate the water inlet pipe and hose with the help of a wrench after the excess water is discharged. However, it is important to note that when dealing with bathroom inlet pipes, you must be very careful to avoid damaging the water pipes by using too much force.

c. Separate the faucet and basin.

In fact, one of the main troubles why many people don't know how to dismantle the faucet is that they don't understand the professional separation technology of basins and faucets. It is accurate to stabilize the water pipe on the one hand, and on the other hand, it can be easily removed by simply turning the wrench.

d. Use a saw to cut the interface.

After the above three processes are completed, it is time for the key link of how to disassemble the faucet, that is, to remove the interface area. It is recommended that you find a special saw for dismantling and sawing off the aging and obsolete faucet, rather than blindly dismantling it manually.

How to disassemble the faucet, the hose and the faucet are connected with threads, the hose is connected to the faucet with a joint, and there is a small hexagon on the joint with a wrench to clamp it and slowly rotate it counterclockwise, you can remove the pipe: 1

Close the hot and cold water inlet valve; 2

Unscrew the two hoses that connect the hot and cold water pipes to the faucet; 3. Unscrew the big nut that fixes the faucet under the pool; 4

Remove the faucet.

How to remove and replace different types of bathtub faucets? Faucet removal and replacement tips.

Various faucet disassembly**, teach you how to replace faucets.

Here's how to disassemble the faucet:

Tools: screwdrivers, wrenches, pliers, faucets.

1. Close the main valve first: to prevent the disassembly of the faucet from affecting the disassembly due to the water coming out of the faucet. Then remove the small screws above or behind the handle, and the handle can be removed, while the screws of some faucets are hidden under the metal buttons, and the screws can be seen as long as the buttons are opened.

However, it should be noted that the inlet pipe needs to be treated first, and the inlet pipe should not be squeezed too hard to prevent rupture.

2. Disassemble the valve core: After removing the handle, you can see the valve core above, and some valve cores have a shell cover on the surface, as long as the cover is removed. At this time, you can see the clamps on the spool, remove the clamps on both sides with pliers, and you need to remove it clockwise, and then the spool can be removed.

3. Separate the faucet and the basin: and then remove all the faucets from the basin, many people don't know how to operate. When separating the faucet from the basin, you need to master the method, if you want to stabilize the water pipe first, and then turn the faucet fixing with a wrench, you can easily remove it.

4. Use a saw to cut the interface: After the faucet is removed from the basin, the interface should be cleaned, and the aging and damaged parts of the interface should be sawed off with a saw. When operating, it is best to find a special saw, if you use an ordinary saw, it is difficult to cut, and it is very laborious.

Precautions for faucet removal

1. When disassembling, if it is very tightly connected with the basin, we should pay attention to the fact that the spool seat may be fixed on the main body of the faucet with a screw, and then use a longer screwdriver to unscrew the screw from below, and then disassemble.

2. If the water inlet hose is brittle or the fasteners are rusty due to too long use, the water inlet hose will not be easy to remove, and we can easily remove a few drops of oil on the rusty part.

01 If you want to disassemble the faucet, you must first close the main water valve at home, and only when the pipe does not enter the water, you can start the disassembly work, which is safer.

02 If it is a kitchen faucet, first separate the faucet from the basin and remove the fixtures of the faucet so that the faucet can be removed from the basin so that the faucet can be replaced.

03 If the main water valve is not closed tightly, as long as the water pressure flowing out of the faucet is relatively small, it can also be disassembled with some water, which is relatively not very convenient to work.

04 If the faucet to be removed is an open pipe, then close the main water valve first, and then separate the water inlet pipe and hose, so that you can twist it down directly with a wrench.

Kitchen and bathroom faucets are easy to break and need to be replaced after a long period of use. How to disassemble the faucet? PChouse will take you to find out.

1. Preparation.

First of all, we need to prepare the relevant things for disassembly, such as screwdrivers, wrenches, pliers, etc., if we want to replace parts such as sealing rings, then we must prepare these small things. In fact, its operation is very simple, that is, after tightening the upper angle valve, put a larger basin under the water pipe to prevent water leakage.

2. Start dismantling and dismantling.

Close the overall valve, remove the small screws above and behind the faucet handle, and remove the handle. There are some faucet screws, which are hidden under metal buttons or plastic buttons, and as long as you open the buttons, you will see the handle screws. However, it is important to remind everyone here that you must be very careful when dealing with bathroom water pipes to avoid using too much force and damaging the water pipes.

3. Separate the faucet and basin.

In fact, many people don't know how to dismantle the faucet, and one reason is that they don't know how to separate the basin and the faucet. It's as simple as stabilizing the hose on one side and easily removing it with a wrench on the other.

4. Cut the interface with a saw.

After the above three steps are done, it is time for the key step of how to disassemble the faucet, where the interface is removed. It is recommended that you find a saw specially used for disassembly, sawing off the aging and waste faucet, and remember not to remove it directly by hand.

Question 1: How to dismantle the faucet Hello! Your faucet is a porcelain core quick-opening faucet (the specification is a four-point pipe thread), not a rubber washer, even if you can buy a new porcelain core, you will still get water everywhere when you replace it, and the main valve can not be closed, you can only replace it with pressure, the method is as follows, please refer to.

1 Choose to replace it when the water is at its peak, so that the water pressure is lower.

2. When replacing, turn on all the faucets in the house, so that the water pressure will be a little smaller.

3 Cover the electrical socket in this room and turn off the main power supply at the same time to prevent water and electric shock.

4 Place wooden utensils and other items in the house in other rooms to prevent moisture.

5. Wrap the newly bought faucet pipe thread mouth clockwise with seven or eight turns of raw material tape facing you.

6. Use a pair of pipe wrenches or a wrench to unscrew the old faucet (be careful, don't use too much force, the faucet will be broken, and it will be very troublesome to break the thread mouth inside).

7. After removing, quickly align and screw the new faucet, and also not too tightly to prevent the thread from breaking.

Question 2: How to disassemble the faucet in the bathroom Turn off the main turn, fix it with a vise, and then remove it with a wrench, and the screws are rusty and put some lubricating oil on the screw contact port, if there is no one at home, then wipe some vegetable oil, and then remove it after a while.

Question 3: How to disassemble the faucet and the car? Faucet disassembly process:

1. Close the total water control valve first to avoid uncontrollable water splashing.

2. Remove the connection with the main water, and then remove the faucet connection.

3. Remove the faucet spout and clean it up.

4. Disassemble the connecting pipe, which is rusty and not easy to disassemble, unscrew it with a wrench and open the inside of the pipe for cleaning.

Question 4: How to dismantle the kitchen faucet at home? There is no need to disassemble other accessories, twist the two hoses counterclockwise from the angle valve, take out the whole faucet, and then grab a hose from the bottom of the faucet and twist it out counterclockwise. As shown in the figure, the installation diagram is for your reference.

Question 5: How to remove the faucet when it is broken Under normal circumstances, it is tight to turn clockwise, as you said, it may not be removed because the thread is rusty, you can try to remove it with a wrench.

Question 6: How to disassemble the kitchen hot and cold water faucet? First, use a small wrench to remove the hot and cold hose from the bottom of the faucet under the basin, and then use a wrench or small pipe wrench to remove the fixing wire and separate it from the basin.

Question 7: How to disassemble the handle of an ordinary faucet Hello, pick up the label on the handle with a toothpick, and then use a Phillips screwdriver to unscrew it to pick up the sail pin.

Question 8: How to disassemble this kind of tap The elbow part of the faucet and the valve body below are sealed with O-rings, which can be directly used. If the whole thing is removed and there is a faucet fixed under the sink, just unscrew it.

Question 9: How to dismantle the faucet pipe with a diagram There is only an installation diagram of a single-hole hot and cold water faucet, I don't know if it can help you.

Question 10: Ask the great god, how to disassemble this faucet? There is a nut under the pool, fix the faucet on the stainless steel pool, and bring the nut down, and you can take the faucet down! It may be necessary to remove the water pipes in advance.

Faucet removal tutorial as if removed:Material preparation: screwdrivers, wrenches, pliers, saws and other disassembly tools, close the main water valve.

Procedure: Empty and empty.

1. Remove the handle, then use a wrench to separate the water inlet pipe and hose, remove the small screws above and behind the faucet handle, and remove the handle.

2. Remove the faucet, then stabilize one side of the water pipe, and turn the other side with a wrench to remove the faucet.

3. The saw saws off the rusty part, and then uses the saw to cut off the rusty part of the interface that is difficult to remove.

Disassembling the faucet requires preparation, separating the inlet pipe from the hose, separating the faucet from the basin, and sawing off the rusty interface with a saw, as follows:

1. Prepare for bright or liquid work: Before replacing the faucet, first close the inlet valve. The inlet valve is located under the kitchen countertop.

If the valve is not closed tightly or cannot be closed, it can be operated with water, but during the installation, the new faucet should be prepared in advance with raw meal tape along the thread direction for 7-8 turns, and a large bucket should be prepared under the water pipe to receive water to prevent waste.

2. Separate the inlet pipe and hose. Use a wrench to separate the inlet pipe and hose first. The water inlet pipe in the bathroom is an open pipe that can be shaken by hand. When disassembling, be especially careful, hold the water pipe with your left hand and twist the wrench with your right hand to separate the two.

3. Separate the faucet and basin. Remove the faucet fixtures so that the faucet can be removed from the basin. When the hose of the faucet has become brittle, and the fixing has rusted and cannot be unscrewed with a wrench, the next step is required.

4. Cut the interface with a saw. It is difficult to operate due to the small space under the basin. And the glass glue between the washbasin and the countertop has long since failed, so the washbasin can be easily removed from the countertop.

Once the basin is removed, the construction will not get in the way. Then use a saw to cut off the rusty part that is difficult to get the lump down, and the faucet is successfully disassembled.

Notes:

1. Some water inlet hoses have been used for a long time, and the water inlet hose cannot be unscrewed for a while due to embrittlement or rusty fasteners. You can take out the basin faucet after two or three drops of oil can be applied to the rusty area.

2. After turning off the kitchen hot and cold water faucet, the water at the outlet has been flowing and cannot be stopped at all, which is usually a problem with the valve core of the water inlet, and the garbage blocks the sealing ring at the bottom of the valve core, the sealing ring is damaged or the impurities in the pipeline scratch the valve core.