How to connect the fiber to the home information box, and can I reuse the switch after connecting?

You can use the Optical Modem to connect and set up the router by following these steps:

One: the connection of the router hardware.

1.First, connect the network cable on the modem side to the WAN interface on the router (this interface is usually colored or positioned to distinguish several other interfaces with the same appearance).

2.In addition, prepare a network cable to connect to any of the four LAN ports, and the other end to connect to the computer network port. (Skip if using wireless).

3.Connect the modem and the power cord of the router, turn on the switch (some brand devices will start automatically after connecting, no switch), and the hardware connection of the above router is complete.

2. Connection settings of the router.

1.Log in to the router settings screen

Open the browser and enter the router login address in the address bar, the login address is different for different brands, but most of them are or check the label on the back of the router or the router manual).

2.Enter the login username and password, the default username and password please check the label or manual on the back of the router.

3.After entering the password correctly, you will enter the settings interface of the router, and the router that has not been set will automatically pop up the settings guide interface.

4.After selecting the connection method, click Next, and the interface of entering the broadband username and password will appear, and the username and password filled in here is provided by the operator when handling the broadband.

5.After filling in the correct username and password, click Next, the connection of the router has been completed, if you need to access the Internet through wireless mode, please see the next wireless connection setting method.

Three: How to set up the wireless connection.

1.Turn on the wireless connection function, set the wireless connection name, and other options are usually default.

2.Set a password for the wireless connection.

3.Turn on the wireless network card on the computer to find the set wireless network name, click Connect, and enter the set password to connect normally.

At home, the optical fiber generally enters the indoor and walks into the weak current box, Netcom or Telecom will give an optical fiber splicing disc and optical modem, the optical fiber is first linked to the optical fiber splicing disc on the optical modem, and the optical fiber line is converted into a network cable, and then it can be connected to a router or a switch

The main line optical fiber access, connected to the input of the optical splitter (EPON technology), is generally connected with the user's pixfirst optical cable with 1 point 8 1 point 16 branches. If the user is connected to the optical modem, there is no need for a switch in the middle.

The network cable connection in the fiber to the home information box is as follows:

1. First of all, make a crystal head according to the connection method of T568B.

2. Also follow the connection method of T568B, and refer to the module prompts to connect the panel.

3. Connect one end of the network cable to a network panel interface on the wall of the room.

4. Connect the connected crystal head with the panel to complete the network cable connection of the information box.

Make a crystal head according to the connection method of T568B.

The other end of the network cable is generally connected to the network panel on the wall of the room, and the connection method of the panel is also in accordance with the connection method of T568B, and there will be a prompt on the module.

Once both sides are connected, the lines to the rooms are basically connected.

The renderings are as follows:

Find the incoming cable and link to the room network cable you want to link Note that it is generally 586B cable pressing If you want to have a network throughout the network, increase the size of the wireless router Incoming line to connect to the WAN port Each room to connect to the LAN port Set the router parameters according to the data provided by the operator There is generally no problem.

After the optical fiber enters the house, it is connected to the "Gigabit port" and then connected to the router.

It means that it is the pigtail of the optical fiber that is connected to your home. This kind of thing can only be received with optical cats. The connection method is very simple, find the pigtail, connect it to the corresponding optical port, and then connect this end to your optical modem.

Now there are three questions, one, do you know which mouth is your family? Second, do you have a light cat at home? 3. Do you have an account password?

So, you can't do it yourself. What a 568b, I can only laugh it off.

No one else can know your stuff unless there is a picture.

The optical modem given by general telecommunications is good, and the bandwidth of 20m is not very large, and the full load is affordable, but the dialing set by the optical modem is really not as stable as the dialing set by the router by itself, my home is 100m optical fiber, and the people of telecommunications come to install the dialing for the optical modem, and then it is really unstable to use, so I changed the route to dial, and now it is much more stable. If you are really worried about stability, buy a better router first, and then connect to the switch.

1.The optical modem can not be put in the optical fiber into the home box, which will reduce the network speed, and the equipment in the fiber into the home box also depends on the networking mode, optical fiber + LAN mode, the home box is a switch (this is called optical fiber into the building), and it can be used without a switch connected to the network cable;

The way is to enter the community with optical fiber, and there is only a splice box in the entrance box, with an ordinary cat;

3.The fiber-to-the-home mode is an optical splitter, and there is no electrical equipment, so you need to use optical modems, and you can't communicate with ordinary cats with photoelectric converters.

4.Modem is a photoelectric converter that can convert 232 485 422 serial signals to optical fibers for transmission, commonly known as serial optical fiber transceivers. It can realize two-way transparent transmission of data between optical fiber and RS-232 485 422 serial port.

Due to the long transmission distance of optical fiber (multi-mode 2km, single-mode up to 20, 40, 60km), strong anti-interference ability, it is the best choice for long-distance transmission connecting remote terminal units to the host and decentralized centralized control system, because optical fiber has a strong anti-interference ability, it can effectively avoid lightning strikes, surges and electromagnetic interference and other damage to industrial data communication equipment and interference of communication lines, and ensure the stability of communication systems.

Pulling fiber to the home requires optical modem equipment.

If you directly pull the network cable into the home, the optical fiber host is connected to the switch in the chassis.

Only one telecom household and one cat (need to change the dedicated because the optical fiber is the input light) Mobile Unicom in the corridor I hope to help you explain unprofessional.

The entrance box is the operator's optical port interface (sub-household port), to your home is the optical modem, the ordinary one is definitely not good, because the entrance is the optical signal, and you must convert the optical signal into an electrical signal through the optical modem before you can access the Internet

The equipment in the fiber-to-the-home box also depends on the networking method, but it is certainly not a cat:

In the optical fiber + LAN mode, the entrance box is a switch (this is called optical fiber entering the building), and it can be used without the switch being connected to the network cable;

The ADSL method is optical fiber into the community, and there is only a splice box in the entrance box, which is an ordinary cat;

The fiber-to-the-home mode is an optical splitter, and there is no electrical equipment, so you need to use an optical cat, which cannot be used with ordinary cats, because it is a photoelectric converter;

As for connecting the router yourself, it's another problem.

Directly take a network cable connected to the computer to connect to the switch, optical intersection first of all, with optical fiber module slot you buy but also buy an optical module, the grade is not in the same grade, 700 are more rubbish.

Fiber-to-the-home to multi-hub boxes.

Connect the LAN port 1 from the modem to any LAN port of the switch. Can.

Optical fiber is an abbreviation for optical fiber, which is a fiber made of glass or plastic that acts as a light conduction tool. The principle of transmission is 'total reflection of light'. Former President of the Chinese University of Hong Kong, Charles Kao and George A

Hockham was the first to propose the idea that optical fiber could be used for communication transmission, for which Charles Kao was awarded the Nobel Prize in Physics in 2009.

Dried tofu, dried Vatican tofu, dried tofu, dried tofu.

Make a crystal head according to the connection method of T568B.

The other end of the <> cable is usually connected to a network panel on the wall of the room.

The connection method of the panel is also in accordance with the connection method of T568B, and there will be a prompt on the module.

After both sides are connected, the lines leading to each room are basically connected.

The renderings are as follows: