The natural gas recharge is successful, but it still can t ignite the fire, what s going on The wate

Reasons and solutions for natural gas stoves not catching fire:

1. The gas stove does not open the gas valve.

Sometimes this situation will also be encountered, generally encountered by the elderly forgot to open the gas valve, want to turn on the gas stove but can not ignite.

Solution: As long as the gas is turned on, it is to open the gas valve and naturally turn on the gas to ignite normally.

2. Dirt from fire extinguishing holes.

When there are a lot of dirty things in the fire extinguishing holes of the gas stove, especially for friends who often cook and don't pay attention to cleaning the gas stove, the gas stove at home is dirty.

Solution: You can try to clean the fire extinguishing hole of the gas stove, because if the fire extinguishing hole is blocked, it will hinder the burner gas mixture to leave it naturally unable to catch fire.

3. The nozzle of the gas stove is blocked.

If the nozzle is blocked, affecting the nozzle to ignite the gas, this naturally cannot catch fire, the light is a little bit of the sound of the fire needle, but it just can't catch fire, this is the nozzle blocked.

Solution: If the nozzle is clogged, you only need to clean the nozzle to ignite normally.

4. The hose is folded.

Generally, the gas pipe of the gas stove is of the hose type, and then it is folded very badly, so that the gas cannot flow normally to the gas stove, and the natural gas stove cannot be ignited.

Solution: It is necessary to find the place where the hose is folded, smooth the hose, and let the gas input normally, so that the ignition can be smoothly.

5. There is no clicking sound of the ignition needle.

If the ignition needle does not make a clicking sound, it is likely that the ignition needle is damaged, the battery under the ignition needle ignition is out of power, and the ignition needle cannot be ignited, which is the most common reason why the gas stove cannot ignite.

Solution: In general, the battery needs to be replaced, especially if the battery of some gas stoves that have been used for a long time is out of power, it will naturally not catch fire.

What is the reason why the gas stove and gas water heater cannot be opened at the same time, is it a problem with the gas appliance or the gas pipe, or the problem of the gas is not ventilated, etc., then we first use the elimination method:

1. Whether the valve in front of the table is closed. This situation is better because the gas stove and gas water heater can be used by turning on the ventilation.

2. In the absence of gas, is the gas meter moving? If there is no gas meter still being done, there must be a gas leak, resulting in the gas stove and gas water heater can not be used at the same time, so we take measures to turn off the valve in front of the meter and contact the gas company personnel to repair.

3. There is a problem with the gas pipeline leading to the gas floor. If there is a leak in the gas pipeline, close the main valve and contact the gas company personnel for maintenance.

Through the elimination method, we can quickly know the result, if the above situation occurs, please contact the relevant professionals to deal with it in time, do not deal with it yourself, it is our responsibility to ensure the safety of our families.

Kitchen and bathroom appliances can choose the era of the brand, the era of kitchen and bathroom has range hoods, gas stoves, gas water heaters, electric water heaters, steam ovens, dishwashers, integrated stoves, integrated sinks, water purifiers, kitchen appliances and other ten categories, positioning the mass market, with the quality that can stand the test, the first and the service that can stand the test to create a cost-effective advantage.

If the water heater and the gas stove can't be turned on, it is likely that the gas meter is out of gas, you can first turn off the valve behind the meter, unplug the hose, and then open the valve to see if the gas meter is supplying, if the gas is supplied, then the problem is the stove and the water heater, look down in order; If there is no gas supply, then you need to replace the gas meter battery, or re-swipe the card to try, because the current gas meter will lock the solenoid valve at every turn, and it will be good to re-magnetize it with the IC card.

The gas has been recharged, but it still can't be called, so confirm whether the recharge has arrived. There will be a while from top-up to gas.

Confirm that it has arrived, and if it is a smart meter, press the button on the meter and try it in ignition.

The gas stove does not catch fire, generally for the following reasons:

1.The gas stove is faulty, the gas stove battery is dead, the lighter is broken, and the stove hole is blocked.

2.The gas pressure is low.

3.Arrears. 4.If it is a smart gas meter, the battery voltage is low and there is no power.

In the kitchen, whether it's a loving breakfast for the family or a delicious late-night snack for yourself, our stoves are indispensable. However, the stove will sometimes have a little temper, but often this trouble, the whole kitchen has to strike for it. If we can't catch fire, we can only stare at these failures?

Don't rush, look down, there is a trick.

Why do you find it difficult to start a fire when using a new stove for the first time? Many new users will let go immediately as long as they see the spark when ignition, so it leads to a decrease in the success rate of ignition, it is recommended that the user press down in place after the operation of the left, and when the sound of clicking is heard, pause for 2-3s (when the Fotile gas stove is used, different brands need to extend the time appropriately), so that the success rate of ignition will be greatly improved. There are two other reasons why this can happen:

1) There is a lot of residual gas in the pipeline, please try to hit it a few times. [You can also operate according to this method after replacing the gas cylinder] (2) The position of the fire cover is not accurate. It is advisable to check that the fire cover is flattened, closed, and the umbrella is aligned with the ignition needle.

There is a clicking sound when the stove is lit, and the spark is faint, but it is difficult to hit or it does not catch fire at all? In this case, it is recommended that you first confirm whether the stove has electricity, when the battery is out of power or weak, there will be a clicking sound, the spark is weak, Fotile gas stove recommends replacing the battery once a year, find the battery box under the stove, generally replace a No. 1 battery.

Why is it difficult to turn on the stove after putting out the pot, or turn off the fire as soon as you let go? It is recommended to wait for the temperature of the stove to drop, and then clean the stains on the inner and outer fire cover, check whether the fire cover hole is blocked, and wipe the copper-colored thermocouple with a dry rag Oh [In the case of letting go of the fire alone, you can also follow this method to operate] The fire cover hole can be dredged with a toothpick.

Is it only half the problem that the fire is out, or is there only a fire in the inner ring and no fire in the outer ring? This situation is usually due to the fact that after long-term use, oil stains and food residues block the fire hole, resulting in a part of the fire not catching fire, and the outer fire cover is usually because the fire groove is blocked.

Cleaning and maintaining the gas stove can effectively extend the service life of the stove and maintain a good use effect. In addition to the normal cleaning of the cooktop and fire cover, the cleaning of the automatic flame-out protection device should not be ignored. In addition, if the gas stove has a movable cleaning cup to help the stove clean, it will make daily maintenance more labor-saving.

Summary. The gas is still not available after charging, it may be due to two reasons: the card is not plugged in properly, or the gas is out for maintenance!

1. Check whether the gas source is open, and whether there is gas For this problem, I believe that friends will not forget, but sometimes they will accidentally turn it off or carelessly forget to add gas, resulting in the situation that it cannot be ignited, so it can be gased. 2. Whether the battery has electricity or not is the most common problem in daily life, and it is also a problem of general concern to the public, if the gas stove is not on fire, it is recommended to check whether the battery has electricity, if there is no electricity, replace the ordinary No. 1 battery. 3. Look at whether the ignition nozzle is on fire 1) If there is no fire, you need to check whether the discharge needle is working normally, if not, it means that there is a problem with the part, and it should be replaced, if there is, it means that the valve body is faulty, and the valve body should be replaced.

2) If there is a fire, it is necessary to see whether it burns normally, if the flame is too weak and cannot reach the furnace head, the air pressure is too low, and it is recommended to replace the new pressure reducing valve; If the flame can reach the fire cover but does not catch fire, it may be that the valve body is blocked, and the nozzle can be unblocked with wire.

The gas is still not available after charging, it may be due to two reasons: the card is not plugged in properly, or the gas is out for maintenance! 1. Check whether the gas source is open, and whether there is gas For this problem, I believe that friends will not forget, but sometimes they will accidentally turn it off or carelessly forget to add gas, resulting in the situation that it cannot be ignited, so it can be gased.

2. Whether the battery has electricity This is the most common problem in daily life, and it is also a nuclear pulse problem that the public is generally concerned about, if the gas stove is not on fire, it is recommended to check whether the battery has electricity, if there is no electricity, replace the ordinary No. 1 battery. 3. Look at whether the ignition nozzle is on fire 1) If there is no fire, you need to check whether the discharge needle is working normally, if not, it means that there is a problem with the part, and it should be replaced, if there is, it means that the valve body is faulty, and the valve body should be replaced. 2) If there is a fire, it is necessary to see whether it burns normally, if the flame is too weak and cannot reach the furnace head, the air pressure is too low, and it is recommended to replace the new pressure reducing valve; If the flame can reach the fire cover, but does not catch fire, it may be that the valve body mill is blocked, and the nozzle can be dredged with iron wire.

You've done a great job! Can you elaborate on that?

4. Overvoltage protection For many gas stoves, there is usually an overvoltage protection device, so once it exceeds a certain value, the gas stove will not start, and it is recommended to replace a pressure reducing valve to try. 5. Pipeline blockage This is the most common type of fault in the use of gas stoves, once this situation occurs, the gas valve should be checked immediately, if you can smell the gas smell, it may be a gas blockage if you say that there is no ear Hanming, at this time you can use the wire to dredge or change it with a new one.

What is the reason for the successful top-up of natural gas or the absence of gas? The card is plugged in to show how much square gas there is, but it can't catch fire and the water heater doesn't have hot water.

Hello, pro 1, did not reopen the solenoid valve for the prepaid gas meter, they have a solenoid valve that can automatically cut off the gas, this solenoid valve will automatically close after the gas meter is in arrears, cut off the gas **. When we recharge again, we can't automatically open the solenoid valve. The reason why this design is to prevent accidental leakage of gas, for example, the valve of the follow-up equipment is not closed, and we do not care about it after recharging, which may lead to gas leakage and cause accidents.

Therefore, many gas meters have to be manually restarted after recharging, and if they are not restarted, they are still not gasy. Solution: There are different methods according to different gas meters, which can be roughly divided into two categories, one is to press and hold the button on the gas meter after recharging, when you hear the sound of the valve opening, the LCD screen shows that the valve is opened, even if it is opened.

The other type is the gas meter without buttons, you need to re-insert the recharge card of the gas meter, insert it into the gas meter, and wait for a few seconds to hear the valve open, and you're good to go. 2. At present, many gas meters are still powered by dry batteries, and when the battery is insufficient, the solenoid valve of the gas meter cannot be opened automatically. Although sometimes, the gas meter shows normal, the solenoid valve still does not open.

The main thing here is that the battery is low enough to support the information display of the gas meter, but not to support the rotation of the solenoid valve motor and open the solenoid valve. Even if it can be used normally when there is gas before, the number of oaks does not mean that it can still support the reopening of the solenoid valve after closing. In this way, there will also be the problem that gas cannot be used after recharging in arrears.

Solution: In the above situation, replacing the battery of the gas meter can solve the problem. The gas meter generally uses 4 No. 5 batteries, let's not care whether it is displayed normally, take out the old battery, replace the new battery and then restart the gas meter to solve the problem.

Generally, the data of the natural gas card is not synchronized to the user's residence. If it's natural gas, it can't be hit. It has nothing to do with Tianfu Weiranqi. I'm from the gas company, and I've had a problem like yours.

1. Check your gas stove, the label under the gas stove will show the type of gas, natural gas and liquefied petroleum gas, if you don't see this, find the gas pressure, the gas pressure of the natural bridge hall wide gas stove is 2000pa, and the gas pressure of liquefied petroleum gas is 2800pa. The liquefied gas stove cannot use natural gas without modification, and try not to modify it, which is prone to danger.

2. The gas meter is not gas, although everything is displayed normally when the battery is pressed, but there will be an internal fault of the gas meter, which depends on whether there is a sound of gas flow when you turn on the gas stove Minliang, in addition to the sound of da-da, if there is a gas flow sound, it is the problem of your gas stove, as mentioned in 1.

3. The purity of natural gas is not enough.

If you've topped up your natural gas card and your gas stove still won't ignite, there could be a few reasons:

Gas valve not open: Make sure the gas valve is open. Check the switch or knob next to the gas valve and set it to the open position.

Gas lines are not connected or leaking: Check that the gas lines are properly connected and make sure there are no gas leaks. If you suspect a gas leak, close the gas valve immediately and contact a professional gas repair technician for inspection and repair.

Igniter issues: Check that the igniter on the gas hob is working properly. If the ignition digger is damaged or fails to produce a spark, it may need to be replaced or repaired.

Cleaning issues: Check that the combustion port of the gas stove is clean. If there is dirt or residue on the combustion port, it may affect the ignition effect. Use an appropriate detergent and brush to clean the burners and make sure they are dry before attempting to start a wildfire.

If you have tried the above methods and still cannot solve the problem, it is recommended to consult a professional gas repair technician or contact the manufacturer or after-sales service center of the gas appliance for accurate fault diagnosis and repair advice. At the same time, ensure that relevant safe operations and precautions are followed when inspecting and handling gas appliances.