How do I make a system clone disk? How to clone a system disk from one disk to another

With ghost this software:

It generally takes no more than 10 minutes to restore the system with ghost, and it takes an hour or two to redo the system and install common software. Therefore, ghost has a powerful and fast function in system backup.

So how do you make a master? Ghost is very good under 98, and the system above win2000 does not have pure DOS, and Ghost must be under DOS to run. Therefore, for more than 2000 systems, before making a system, you should use the win98 boot disk with format c:

Format the system disk,Then install the system,After installation, there will be a dos option,Then use ghost to back up your system,Once the system has a problem,Restore it and it's OK。

If you don't format the system disk according to the above method before making the system,You can go to the next MXDOS,It can add a pure DOS entrance for your win2000 or more system,With DOS, you can use ghost backup to restore。

Make the system, install common software, games, if it is a system of more than 2000, it is recommended to optimize it, especially the XP system, ** is very necessary.

Single-disk Kelong is simple, hang a hard disk to be engraved on the computer where the master disk is located, engrave the disk under DOS, engrave the partition, and the whole disk Kelong is OK.

If you need to make a large LAN, network engraving is a must, that is, to make a master disk, use the network, load the network card driver and then carry out the network engraving, after the engraving of each computer's system content is the same.

How to clone the original original hard disk C drive system into a new hard disk, you will also be after reading it!

If you want to back up your system, use ghost to select Disk to Image. You will be prompted to select the source disk you want to back up (usually C drive), and then select the path where you want to save the mirror file. If you want to restore, you can do an image to disk.

That's probably it, and there's no problem with the above NTFS partitions.

If you finish the system and then make a ghost scene file yourself and back it up, then you can clone it directly.

If you want to use a master disk that has been done to clone another child disk, you can use ghost software, after entering the selection of three are the first item, and then you can clone after selecting the master disk and the slave disk, but be careful not to contradict it, or your master disk will become the same as the child disk! You can create a folder in the master disk that you recognize yourself, and you won't go wrong when it comes to grams!

The so-called clone disk is also the original disk.

Divide the original disk into sections, and after formatting, just do a good job of the system. You can use ghost, but the partition format must be FAT (16 or 32).

You must have ghost software. Then it's a matter of putting the original tray into the system. Then connect it from the disk to DOS and then make a ghost clone.

With one"Startup disk"Start your computer.

Go into pure DOS and do it with the ghost tool.

Select Local Partition to Image, then select the partition you want to back up, then select the name you want to save, and just continue.

You can use Ghost, but the partition format must be FAT (16 or 32), or use the ISO image to engrave it to the disc (any disk will do, but you must install your system), as long as the hardware configuration remains the same, and the NT kernel uses a universal driver, you can use it!

Joy is just joy with you.

I originally wanted to write it myself, but I didn't add it, so I found one directly on the Internet and sent it to you, ok

Tools Materials.

Aomei easily backs up your computer.

Here's how. <>

2. After entering the page, select a disk to clone, as shown in the figure below, select disk 0.

3. Then you need to select a location to clone to, as shown in the following figure, select disk 1.

4. Make sure the disks are selected correctly, click the "Next" option, and wait for the system to clone automatically.

5. As shown in the figure below, wait for completion.

<>2. After opening the software**, in the partition assistant window, left-click the system disk c of disk 1, and on the left side of the window, click Migrate the system to a solid-state disk (click this item for mechanical hard disks).

3. In the open solid-state disk migration system, click Next.

4. In the "Select Disk Space" window, left-click the unallocated space of Disk 2 and click "Next".

5. In the window of resizing the partition, we create the main partition by default, use the symbol d (you can change the drive letter later), and then drag the small dot pointed by the arrow to the left with the mouse to adjust the partition to 101g (for example, if you install a dual system later, the software program will be installed on the system disk, so install 101g. If you're not ready to install a dual system, you can only arrange about 50g). Then click Next.

6. In the "Boot Operating System" window, Huai Noise clicks "Finish".

7. Go back to the Partition Assistant window and click Submit in the upper left corner.

8. When the dialog box pops up, click Execute.

9. Click "Execute", and then click "Yes".

10. After the computer knows which new one is started, the system migration operation will be automatically performed, and the computer will be restarted 2-3 times during this period. After the system migration is complete, shut down the computer, disconnect the power supply, remove the source disk, connect the new disk to the slot of the source disk, and then turn on the computer.

To clone a hard drive system to an SSD, follow suit:

1. Make a USB flash drive tool of a PE system and use it to start the computer to the desktop;

2. Run the ghost software included in the system, make the main partition data of the original mechanical hard disk into an "image file", and save it to a USB flash drive or mobile hard disk;

3. Shut down the power off, remove the mechanical hard disk, if it is a desktop, directly attach the SSD hard disk, and install the SSD hard disk to the original mechanical hard disk location;

4. Still use the USB flash drive to boot the system, and after entering the desktop, use the ghost tool to release the saved "image file" to the designated SSD hard disk main partition;

5. After completion, restart the computer, enter the BIOS elimination window, set the SSD hard disk as the first boot device, restart the computer after the security bridge is saved, and check the system startup and running status in the SSD hard disk.