70 is enough, how to adjust the car handbrake cable

1.Determine the position of the handbrake handle.

To check whether the handbrake is normal, you can first check the handle position of the car handbrake. Normally, when the handle is lifted to 70% of the full stroke, the handbrake braking system should be in the normal braking position, so before checking the braking force of the handbrake, you should first find out this 70% working point, which can be determined by counting the ratchet sound.

2.Check if the handbrake is working.

Drive the car to a slope with a large slope and a good road condition (preferably an asphalt road), press the brakes, put the gear position in neutral gear (or hang it in N gear if it is an automatic transmission), and pull the handbrake handle to the position of the working point just determined. Then slowly release the brake pedal, if the car does not slip, it means that the handbrake is working well. This inspection should be done once on the uphill slope and once on the downhill slope.

3.How to adjust the handbrake.

In the above inspection, if it is found that the braking efficiency or sensitivity of the handbrake is not ideal, it can usually be solved by adjusting the operating copper cable of the handbrake. There is an adjustable compensation mechanism at the junction between the bottom of the handbrake handle and the copper cable (generally covered by the interior parts), and the length of the brake copper cable can be stretched by loosening the lock nut with a wrench. However, the adjustment mechanism of some cars is located at the bottom of the car, and if it is inconvenient to adjust, it should be handled by professional maintenance personnel.

If the handbrake is loose, it is recommended that you do not adjust it yourself, but go to a 4S shop or other car repair shop to repair it. After all, you are not professional enough and do not have some professional tools, and you also have to think about your own safety and the safety of others. For specific operations, you can follow the following steps, for reference only:

1: Open the armrest box and remove the two fixing screws inside.

2: Loosen the handbrake wire fixing bolt to the loosest state.

3: Ignition in neutral, press the brake twice, and then you can see that the steel wire that was originally pulled out is withdrawn.

4: Turn off the heat. 5: Begin to tighten the handbrake wire fixing bolts, generally the bolts are exposed 1cm most sometimes start to try to pull the handbrake, I adjust the 5-6 gla death, this is a personal suggestion, this is the best distance I try to come down.

6: After adjustment, let go of the handbrake, light the brake and step on the brake more, turn off the engine and get out of the car to retreat to see, if there is no very laborious state, it means that the adjustment is very good, if it is very laborious to push, the handbrake adjustment is too tight, to loosen it, but it is recommended to follow the first method in the re-get.

Hope! Thank you.

If you need to replace the car handbrake cable, you need to go to the 4S shop or repair shop of the car to replace it. It cannot be replaced by itself to avoid damage to the car's handbrake parts.

The car handbrake is regarded by the driver as the last safety barrier, but when the handbrake is used too frequently, its effectiveness will be reduced. In many cases, it is clear that the handbrake has been pulled, but it cannot play its due role due to system failure or improper use, which is also a major hidden danger of causing accidents, so the owner should regularly maintain and check the handbrake.

The traditional handbrake needs to rely on the driver to start comfortably by manually releasing the handbrake or skillfully throttle and clutch cooperation when starting on a slope.

The Auto Hold automatic parking function gives accurate parking force by the controller through the slope sensor, and when starting, the parking control unit automatically releases the parking brake when the driving force is greater than the driving resistance through calculation, so that the car can start smoothly.

Even if you are congested and parked in the city, as long as you enable the auto hold function, the corresponding automatic parking function will be activated. The intelligent Auto Hold function allows the vehicle to automatically activate the four-wheel brake when waiting for a red light or stopping uphill or downhill, even in D or N gear, you don't need to keep your foot on the brakes or use the handbrake, the car is always stationary.

When it is time to release the standstill state, you can also release the brake with a simple tap of the accelerator. This configuration is really practical for those car owners who often stop and go in the city, and it also reduces some unnecessary accidents caused by everyone's carelessness.

It can be solved by adjusting the handbrake cable, and there is an adjustable compensation mechanism underneath the handbrake handle. When adjusting, you need to remove the decorative cover of the handle first, and then use the tool to adjust the length of the cable to ensure that the hand brake is in the best working condition.

However, few car owners will pay attention to check the hand brake, most of the vehicle's hand brake needs to be adjusted, experts remind the majority of car owners not to ignore the importance of hand brake, hand brake work poor need to be adjusted in time.

Hello, friend.

There are adjusting screws on the handbrake cable.

Twist it with a wrench.

Hello, friend.

There are adjusting screws on the handbrake cable.

Twist it with a wrench.

Hello!Some cars can be adjusted behind the middle armrest, and some cars need to be jacked up to adjust [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Hello, the handbrake line of the car is loose, how to adjust it? The loose handbrake cord of most models is caused by the wear of the handbrake pads. After replacing the handbrake pads, it's basically the same. I hope my answer is helpful to you, and I hope to adopt it, thank you.

This is normal, the car handbrake is a main wire rope to the rear axle, and then the tail end is fixed on one side of the rear axle, divided into two by the brancher, and the two auxiliary cables are respectively to the brake drum (disc) on both sides, because the main cable is on one of the sides, so the length of the two auxiliary cables is different.

Summary. The handbrake cable adjustment method is as follows; 1. First check the vehicle handbrake cable to ensure that the handbrake cable is not damaged, not broken, deformed or worn, and ensure that the cable can be used normally. 2. Check the adjusting bolt of the vehicle handbrake cable to ensure that the adjusting bolt of the cable is not loose or damaged, and ensure that it can be used normally.

3. Disassemble the handbrake cable, pay attention not to break the cable when disassembling, and tighten both ends of the cable and not to break it. 4. Tighten the cable adjustment bolt and adjust the length of the cable to ensure that the length of the cable is suitable for the vehicle. 5. Install the cable and install the cable on the vehicle handbrake cable hanger to ensure that the cable can slide normally on the hanger and is not affected by tension.

6. Pull wire pull test, the pull force of the pull wire should be within a certain range, and exceeding the range will affect the normal use of the handbrake. 7. After completing the adjustment, check whether the length and tension of the cable meet the requirements of the vehicle to ensure that the cable can be used normally.

Dancheng County, Henan Province**, there is a place to sell Volkswagen Lavida handbrake cables.

The handbrake cable adjustment method is as follows; 1. First check the vehicle handbrake cable to ensure that the handbrake cable is not damaged, not broken, deformed or worn, and ensure that the cable can be used normally. 2. Check the adjusting bolt of the vehicle handbrake cable to ensure that the adjusting bolt of the cable is not loose or damaged, and ensure that it can be used normally. 3. Disassemble the handbrake cable, pay attention to the cable not to be broken when disassembling, and the two ends of the cable should be fastened and not broken.

4. Tighten the cable adjustment bolt and adjust the length of the cable to ensure that the length of the cable is suitable for the vehicle. 5. Install the cable and install the cable on the vehicle handbrake cable hanger to ensure that the cable can slide normally on the hanger and is not affected by tension. 6. The pull force of the cable should be within a certain range, and the normal use of the handbrake will be affected if the range is exceeded.

7. After completing the adjustment, check whether the length and tension of the cable meet the requirements of the vehicle to ensure that the cable can be used normally.

It is sold in the local auto parts city.

But now that the Chinese New Year is approaching, it should all be a holiday.

What to do if the handbrake line is elongated The handbrake line is generally not longer and longer, because it itself is relatively tough and will not be so easy to pull long: 1. The first oak professional name of the handbrake is the auxiliary brake, which is different from the principle of the brake, which is connected to the rear brake shoe by using a steel wire cable to brake the car; 2. When driving with a handbrake, the most direct hazard is that the brake disc will accelerate and wear and the brake pad will harden after heating, which will lead to a great decline in brake performance, and sometimes the burnt smell can be smelled because of this; 3. If the handbrake is pulled for a long time, it may also lead to the brake cylinder being crushed, the brake fluid leaking, and the brake fluid temperature being too high, resulting in the complete loss of the brake function of the car. @2019

Replacing the handbrake cable is very simple. First of all, disconnect the connection of the handbrake lever, then disconnect the connection of the rear brake caliper, and finally disconnect the buckle on the chassis that lacks the handbrake cable to fix the handbrake, so that the old handbrake cable can be removed, and finally the new one is installed.

However, the handbrake cable is not something that can be replaced by the owner himself, and it needs to be replaced by professionals.

The handbrake cable is only available in cars equipped with mechanical brakes, and most cars will be equipped with mechanical brakes or electronic parking brakes.

The electronic handbrake does not have a handbrake line, and the structure is different from the mechanical handbrake.

Cars equipped with electronic handbrakes have handbrake motors on both rear wheels. When the electronic handbrake button is pressed, the handbrake motor will clamp the brake pads, which can prevent the car from skidding.

Cars equipped with manipulator brakes have handbrake levers and handbrake cables, which will loosen when using the handbrake cables for a long time, and the owner needs to tighten the handbrake cables.

If the handbrake cable is broken, it needs to be replaced.

The mechanical handbrake is something that will soon become obsolete. Most cars use an electronic parking brake.

Generally, cars equipped with electronic parking brakes also have the autohold function, which is quite convenient to use with electronic parking brakes.

The electronic parking brake is easy to use and can improve the driving experience.

If you are interested in electronic parking brake, you can give it a try.

Millions of car purchase subsidies.