How to operate the car to start? Car start up steps

Hello, this step for your reference:

Star, hang a gear, slightly increase the throttle, loosen the clutch, loosen to a certain extent, the car walks up, increases the throttle, and the car starts quickly. Pay attention to the coordination of the throttle and the clutch, people who have just started to practice, generally like to put the throttle first, and then the clutch does not dare to put it, the engine is buzzing, but the car does not move! I'm also very nervous!

There are three elements of the clutch, fast, pause, slow, first fast, soon to a certain extent, the clutch and power engagement, at this time, to pause, and then slowly release the clutch! Proper gas pedal! If you start, especially when starting on a ramp, if you find that the body is shaking, it means that the power is not enough, put more clutch or increase the throttle!

The car began to run, when the engine sound began to roar, it was necessary to upshift, theoretically so, in fact, the car began to go, on the second gear, some people simply started in second gear, the speed of the second gear is about the same as running, the third gear is 40 yards, the fourth gear can be seventy or eighty, some look at the car, the main thing is to listen to the sound, and the main thing is to find the feeling, drive more! Pay attention when you want to upgrade the gear, first raise the speed when you want to upshift, such as hanging the third gear in the second gear, add more throttle in the second gear, reach the speed of the third gear, step on the clutch, shift gears, the main thing is that the process should be very smooth! Don't look at the handle when you usually hang the gear, you have to feel it!

Pay attention when downshifting, if the brakes are more urgent, don't worry about the gear first, step on the brakes first, and look at the road conditions ahead! As long as the car is not fast enough to stop, it will not turn off, when it is really slow, you can step on the clutch, if the car is still fast after braking, judge the gear you should use according to the speed at that time.

Drive with gas, be fast when you should be fast, slow when you should be slow, and don't let the people in the car feel scared! Peace be upon you!

Whether it is a manual transmission or an automatic transmission.

Car start-up stepsCar starting operation steps: 1. First open the door, sit in the driving position, adjust the seat, and fasten the seat belt.

2. Turn on the turn signal to remind the vehicles and passers-by behind. 3. Insert the key ignition start, step on the clutch with the left foot, hang a gear with the right hand, put the right foot on the accelerator pedal at the same time, gently lift the clutch with the left foot, when the clutch is lifted to the semi-linkage state, when the car shakes slightly, the right foot gently steps on the accelerator, and at the same time releases the car handbrake, completely loosens the clutch, and the car starts the car steps: 1. The clutch slowly lifts the clutch and shouts quickly, and the car stabilizes the clutch when there are signs of shaking, slowly lifts the brake, and gently steps on the accelerator to make the speed to about 1300-1500; 2. Then the left foot continues to slowly release the clutch, and the right foot continues to lubricate synchronously, the faster you need to start, the more you need to refuel, but at the same time, the clutch should be released faster; 3. After all the leases are loosened, the car continues to move forward, and the speed is about 1800-2000 to change 2 gears, and then every 2000 to change gears.

Generally, when the car starts, it is necessary to press the accelerator while releasing the clutch.

1. Flat road starting operation:

First step on the clutch erector pedal with the left foot, hang the clutch pedal with the right hand into 1st gear, press the horn with the left hand, release the parking brake lever with the right hand, and then slowly lift the clutch pedal with the left foot to semi-linkage, slowly step on the accelerator pedal with the right foot to refuel, let go of the clutch pedal with the left foot after the car starts, and finally refuel with the right foot to speed up to the normal speed, drive the car into the normal lane and turn off the turn signal.

2. Half-slope starting operation:

When starting, due to the greater resistance, so the clutch should be more stable than the flat road 3-4 seconds, when you put down the hand brake, do not immediately loosen the clutch, Ling Fiber must be refueled immediately, and so that the car travels slowly 3-4m, and then slowly lift the clutch, so as to ensure that the car starts smoothly on the ramp without stalling.

To dare to refuel, start uphill, put down the handbrake, immediately refuel, so that the speed of the engine reaches about 1500 rpm, so as to ensure that the car uphill start with sufficient power, there will be no "shaking" phenomenon. The key to a smooth start on a ramp is to coordinate your hands and feet properly, otherwise, it will cause the engine to stall or the car to slip backwards.

Release the handbrake with your right hand and hold down the front of the handbrake, then stretch out the handbrake to completely press down the handbrake and release the handbrake. The left leg slowly stretches out upwards until the clutch is in a semi-clutch state, according to the different sensing points of the clutch, the half-clutch height is different, usually raised by 30-45 degrees in the middle position, the vehicle gradually trembles slightly, which means that the car power is enough.

When driving, it is very important to start, and you must develop the habit of starting in 1st gear, which is good for the car engine, clutch, and gearbox. The operation essentials of the clutch pedal at the start are one fast, two slow, and three linkages.

Correct operation

When the clutch pedal is semi-linked (at this time, the sound of the car engine changes), the speed of the foot pedal extension is slightly slower, and the foot pedal is slowly extended from the linkage to the process of complete cooperation. At the same time when the clutch pedal is extended, gradually press the accelerator pedal according to the size of the car engine's resistance to the land, so that the car can start smoothly.

Before starting the engine, be sure to check that the parking brake handle is pulled up and tightened, and that the gear lever is in neutral or P position. The time of each use of the starter shall not exceed 5 seconds, the interval between the two times shall not be less than 15 seconds, and the engine shall not exceed 3 times in a row.

The operation of starting from the car is to get into the car and prepare, adjust the seat, start the engine, put the gear, observe the road conditions, and start.

1. Get on the bus and prepare. Before getting into the car, you should walk around the car, check the condition around the vehicle, and pay attention to whether there are obstacles under the car and around the body. You can only get on the car after confirming that it is safe, because there are many blind spots in the car, and the vision is very limited when you look through the rearview mirror.

2. Adjust the seat. After getting into the car, we must first adjust the seat and backrest, improper sitting posture will cause us to feel abnormal when driving. If we can't flex or extend our legs freely, it will be very tiring to control the throttle and clutch for a long time.

After adjusting the seat, adjust the mirrors, and then fasten the seat belt.

3. Start the engine. After the car starts, usually we have to observe the indicator light in the dashboard, if the fault light is on for a long time, it means that the fault light is abnormal for the components, and the engine should be turned off immediately, and the vehicle should be checked and troubleshooting.

Getting Started:

1. Novices should pay attention when starting: learn to use the clutch pedal, accelerator pedal and brake pedal reasonably when starting. In the normal start, it is required to start smoothly and safely, to have a correct driving posture, not to look down at the parts, to look at the front and both sides of the road, and to start without rushing, shaking, stalling and intermittent arching.

2. Before starting, carefully inspect the condition around the vehicle, and pay attention to whether there are obstacles under the car and around the body. The engine needs to be warmed up when starting from a cold car, and the warm-up time depends on the temperature, and the idle speed is generally required to return to normal before starting.

3. Always remember to wear a seatbelt. Check if the driver's seat and mirrors are positioned appropriately, and adjust them if not. Adjust your sitting posture appropriately.

Driving to have a good sitting posture is not for pose, it is closely related to safe driving and riding comfort. A good sitting posture requires the driver to have their hands on the steering wheel naturally, their backs lightly pressed against the back of the seat, their eyes looking straight ahead, and their feet naturally resting on the pedals.

Starting is one of the basic skills that drivers must master when driving a vehicle, and the correct starting operation can ensure a smooth start and ensure safe driving. The following will introduce the specific operation steps of starting the car.

Adjust the seat position and mirrors.

Before starting, the driver needs to adjust the seat position and mirrors to ensure that they are seated comfortably and have a clear view of the vehicle.

Press the clutch.

Stepping on the clutch is the first step in getting the car started, and the clutch is used to disengage the engine from the transmission. While depressing the clutch, the brake pedal needs to be pressed to prevent the vehicle from slipping.

Gear. After pressing the clutch and brake pedals, the gear needs to be adjusted from neutral to first gear. When shifting gears, you need to make sure that you are in the correct gear to avoid danger.

Release the handbrake. Before the car starts, you also need to release the handbrake so that the vehicle can slide freely.

Release the clutch and brake pedal.

When the above steps are completed, the clutch and brake pedal need to be released slowly. It needs to be done slowly and evenly when releasing the clutch and brake pedal to ensure a smooth start of the vehicle.

When the clutch and brake pedal are fully released, proper throttle is required to ensure that the engine can propel the vehicle forward smoothly. The force of the accelerator pedal needs to be adjusted according to the road conditions and speed to avoid overspeeding or erratic driving.

Shift gears correctly. When the vehicle is moving, it is necessary to change the speed according to the speed of the vehicle and the road conditions. When shifting, you need to first press the clutch, then shift to the next or previous gear, and finally release the clutch slowly.

When shifting gears, it is necessary to pay attention to the accuracy and smoothness of the gear to ensure the smooth and safe driving of the vehicle.

In short, starting the car is a basic skill that the driver must master, and the correct starting operation can ensure a smooth start of the vehicle and ensure the safety of driving. It should be noted that you need to pay attention to the situation around the vehicle at all times during starting and driving, and maintain a high level of vigilance and caution.