How many degrees are set for the manual water boiler, and how to adjust the temperature of the comme

Hello dear! The way to adjust the temperature of the commercial water boiler is as follows: fill the container with water, cut off the power supply, remove the electrical box cover, and then turn on the power supply to make the water boiler in normal working condition; (2) If the water temperature is lower than 98, the thermostat is not turned on, and the heating element is not heated, please adjust the thermostat knob clockwise to the thermostat to turn on (green light on); (3) If the water temperature reaches 100 degrees Celsius and the thermostat is not turned on and the heating element does not stop heating, please adjust the thermostat knob counterclockwise to the thermostat to disconnect (the green light is off).

After Hongchang repeated 2 or 3 cycles of adjustment, the requirements can be met. Hopefully, this service will help you <>

<> you can click on my avatar to follow me, and if you have any questions in the future, it is convenient to consult me again, and look forward to serving you again. Wishing you well; Have a good life and all the best! If you are satisfied with my service, please give a thumbs up<>

Once again, I wish you all the best! Peace and joy.

There are differences between models. You may have a digital display (if it's analog, just adjust the temperature setting knob). Take a certain paragraph as an example, the following is for reference:

When the power is turned on, press the temperature adjustment button, and the digital display flashes to display the last set (or factory default) temperature, such as 75 degrees you talked about (generally this 75 degrees is the maximum temperature that can be set). Each time the temperature adjustment button is pressed, the setting value changes by a certain amplitude (e.g. 5 degrees), which can generally be cycled between 30 and 75 degrees. For example, the original 75, press once to change to 30 degrees, press again, change to 35 degrees, press again, change to 40 degrees (press and hold the button continuously, it will also change according to the amplitude of the continuous ladder).

You can set it to the desired temperature accordingly. After 3 seconds, the system automatically confirms that the temperature is the set temperature, and the monitor resumes to display the actual temperature of the water temperature after 1 second.

Generally, the microcomputer control has a power-off memory function (generally, the "reservation function" does not remember), even if the power is off, and then the power is sent to work, the set temperature will still be remembered and retained, and there is no need to adjust it again.

If you have a mixing valve and many people are going to take a shower continuously, it is recommended that the temperature should not be set too low, for example, it can be set to 55 degrees, 60 degrees, 65 degrees. If you don't have a mixing valve and you're only using it for 1 person, you can set it to 45 degrees.

When not necessary, of course, setting a low point is good for the life of the water heater and can also save energy. How much is better to set can be determined according to actual needs.

Summary. Hello! The method of adjusting the temperature of the commercial water boiler, the way of adjusting the temperature of the commercial water boiler is as follows:

Fill the container with water, cut off the power supply, remove the electrical box cover, and then turn on the power supply to keep the water boiler in normal working condition; (2) If the water temperature is lower than 98, the thermostat is not turned on, and the heating element is not heated, please adjust the thermostat knob clockwise to the thermostat to turn on (green light on); (3) If the water temperature reaches 100 degrees Celsius and the thermostat is not turned on and the heating element does not stop heating, please adjust the thermostat knob counterclockwise to the thermostat to disconnect (the green light is off). After repeated 2 to 3 cycles of adjustment, the requirements can be achieved.

Hello! The method of adjusting the temperature of the commercial water boiler is as follows: fill the container with water, cut off the power supply, remove the electrical box cover, and then turn on the power supply, so that the water boiler is in a normal working state; (2) If the water temperature is lower than 98, the temperature control is not connected to Kailiangtong, and the heating tube is not heated, please adjust the thermostat knob clockwise to the thermostat to turn on (green light is on); (3) If the water temperature reaches 100 degrees Celsius and the thermostat is not turned on and the heating element does not stop heating, please adjust the thermostat knob counterclockwise to the thermostat to disconnect (the green light is off).

After repeated 2 to 3 cycles of adjustment, the requirements can be achieved.

Hello! The above is how to adjust the temperature of a commercial water boiler.

When summer comes, the water temperature must be low, so if you lower the heat point knob or turn it to a simmer,If the water temperature is still too high, you can also adjust the water temperature according to the adjustment of the water temperature knob or the water seepage proportional valve, generally in summer, the water temperature knob is adjusted from high to low or the proportional valve is adjusted from small to large, and the satisfactory water temperature can be adjusted. The first thing to check is the stress in your home. In some homes, the water pipes are exposed to the outdoors, and the temperature of the water in the pipes is likely to reach around 35 degrees Celsius after being exposed to the sun.

This also means that the water in the water heater is already very hot before it is heated, and the water temperature will be higher when it is heated through the water heater in the middle and later stages, and the water released in it will of course be hotter. First. If the cold water is especially large.

The flow of hot water is small. Then check the hot water gate valve, tap faucet, and shower nozzle to see if there is any blockage, and make the water from the water heater drain outlet immediately, and see the water flow size. Inspection of a section of water mains and a section of water pipes.

The flow of water in hot water has increased, and the temperature has of course decreased secondly. For example, hot water, cold water, are very small.

Indicates that there is little stress at home. It is necessary to consider installing an automatic booster pump to increase the water flow. Then of course, the temperature will be reduced.

Third, you can also use the manipulation, the size of the valve, to manipulate the water temperature. The factor of the problem is that the tap water temperature is too high. Natural gas water heaters are water-vapor linkages, and the water flu responder will ignite as soon as the water flow is detected.

You must have an exposed part of the water pipe, and the temperature of the tap water may already be 30 degrees in the summer, and then it is undoubtedly far higher than the comfortable 38 degrees in the summer when you take a bath.

Close the bypass valve of the natural gas water heater and adjust it little by little to the minimum force that does not affect the application. It is sufficient to make the fire discharge only ignite with the minimum amount of natural gas, so that it can meet the normal operation situation. Modify the booster water pump to make the water flow according to the burner as soon as possible, and reduce the heating time of the water flow, which can also effectively reduce the water temperature of the water output.

The toilet tap water inlet was retrofitted with a teeImmediately received the shower shower, the tap water temperature is hot to this level and the branches collapsed, immediately shower without a problem.

As an electrical product, the safety of commercial electric water boiler is very important. Since the general consumer does not have the knowledge of electricity, it is best not to install it by yourself after purchasing the product, and it is best to install it by the professionals of the manufacturer. Before using the product, consumers should carefully read the product instruction manual and operate in accordance with the instructions.

Generally, the water boiler should be placed on a solid platform, and there should be a drainage floor drain near it, so that the water boiler can be cleaned and drained and overflow under fault conditions. The external power supply should be installed with an independent power switch and leakage protection device before connecting to the water boiler. The metal casing of the water boiler should be reliably grounded.

Consumers should pay attention to the following 6 aspects in use:

1 Do not install the water boiler in a humid environment, such as in the bathroom. Because the air in the bathroom is humid, the water vapor is easy to condense on the surface of the insulating medium after entering the electrical box, reducing its insulation performance and causing leakage accidents.

2 When using the water boiler, it should be filled with water before turning on the power supply, and do not adjust the thermostat by yourself to prevent the thermostat from being adjusted above the boiling point temperature. There is an instantaneous energy-saving water boiler that prevents dry boiling, and when the water is connected, the water will automatically enter the working state after the power is on.

3 During use, do not remove the grounding wire of the water boiler, because the grounding measure is the last protective measure to prevent the contact of Jianyu Electricity. 4. Always check the inlet water source of the water boiler to prevent the water inlet from being blocked and avoid the occurrence of dry burning of the electric heating pipe.

5 Descale regularly. If the local water quality is poor, a water purifier can be installed at the water inlet of the water boiler to improve the work efficiency of the water boiler, prolong the service life, and ensure the cleanliness and hygiene of drinking water.

6. Before maintaining and cleaning the water boiler, the water source and power supply of the water boiler must be cut off. When cleaning the shell of the water boiler, it should be wiped with a clean rag, and it is strictly forbidden to rinse the shell and electrical box with a jet of water.

1. Do not install the water boiler in a humid environment, such as in the bathroom. Because the air in the bathroom is humid, after the water vapor enters the electrical box, it is easy to condense on the surface of the insulating medium, reducing its insulation performance and causing leakage accidents.

2. When using the boiling water machine, it should be filled with water before turning on the power supply, and do not adjust the default setting content of the circuit version at will to prevent unexpected safety problems.

3. During use, do not easily remove the grounding wire of the water boiler, because the grounding measure is the last protective measure to prevent electric shock.

4. It is necessary to check the inlet water source of the water boiler frequently to prevent the water inlet from being blocked, and avoid the occurrence of the phenomenon of dry burning of pure pipes (of course, the water boilers are now anti-dry burning).

Water heater is one of the most important household appliances in our daily life, if you want to take a hot shower, you must know how to turn on the water heater water temperature switch correctly. Here are some simple steps that can help you turn on your water heater water temperature switch successfully.

Step 1: Know your water heater type.

Before turning on your water heater, you need to know your water heater type and operate it according to its characteristics. Generally speaking, there are two types of water heaters, which are gas water heaters and electric water heaters. If your water heater is an electric water heater, then you just need to find the temperature knob on your water heater.

If your water heater is a gas water heater, the temperature knobs and gas valves you need to operate may vary.

Step 2: Confirm the position of the water temperature switch.

The location of the water heater water temperature switch may vary depending on the brand and model. Generally speaking, on electric water heaters, the temperature rotary Zheng Ji button is usually located on the front or side of the water heater and is marked with different water temperature scales. On a gas water heater, the temperature knob or control switch may be located on the top or side of the water heater, while the gas valve is located on the bottom.

Step 3: Check the gas and electricity.

Always make sure that the associated gas and electricity** are turned on and working properly before operating the water heater. If both the gas valve and the power supply are turned on, the appliances or components in the water heater can work properly.

Step 4: Adjust the water heater temperature.

Toggle the temperature knob or adjust the water heater switch until you are satisfied with the water temperature. If your water heater is an electric water heater, you should not adjust the temperature too high to avoid damage to the water heater. If your water heater is a gas water heater, you should gradually adjust the water temperature by turning the temperature knob left or right.

Step 5: Wait for the water temperature to rise.

After you adjust the water temperature of your water heater and turn it off early, you need to wait a while for the water in the water heater to rise to a suitable bath temperature. In general, the water temperature inside the water heater can rise in just a few minutes, allowing you to enjoy the comfort of a hot bath as soon as possible.

Overall, turning on the water temperature switch of the water heater is a very simple operation. As long as you follow the steps above correctly, you can enjoy a comfortable hot bath in no time.