How should I wash my skates?

Single-row roller skate cleaning is mainly for bearings and shoe lining, the following methods can be used:

Cleaning of bearings: Prepare a dry cloth or toothbrush.

If the bearing is contaminated with dust, it can be cleaned with a dry cloth or toothbrush.

If the bearing has been used for a long time and feels unsmooth or has a loud "rustle" sound when sliding, you can take off the bearing, soak it in the "stain removal oil" for about half an hour, clean off the impurities in the bearing, and then spray the engine oil or special oil for the bearing.

2.Cleaning of the inner lining: Prepare warm water, detergent.

Start by adding a professional detergent. Place the liner in the laundry tub and add warm water. Soak overnight, take it out the next day, and leave it in the shade to dry.

How can you tell if bearings need to be cleaned and replaced? You can tell from the following:

1.When the wheel turns, there is a strange sound, such as a rustling sound, which may be the bearing forest entering the sand.

2.I feel that the speed of the wheels has slowed down a lot.

It should be noted that once the bearings are dismantled, after washing, the original thicker lubricating oil will be washed off, and it will become easier to enter the sand than before, so the general advice is: unless it is really unbearable, or really idle, otherwise do not take it apart and wash.

Preparation tool: Allen wrench x2

2.Clean rag x1

3.Toothbrush x1

4.Cleaning container (wide-mouth basin) x1

5.Slotted screwdriver for lock glasses x1

Unleaded petrol or stain remover oil.

7.Lubricating oil (e.g. WD-40, sewing fluid).

Working Steps:1Remove the bearings from the rim after removing the wheels.

2.Take a screwdriver for glasses and remove the C-ring of the cartridge bearings.

Remove the dust cap after removing the ring.

4.Then put the dismantled bearings into a wide-mouth basin and pour in the clean solvent.

5.Use a toothbrush to clean the butter and dirt in the bearings.

6.Wipe the washed bearings with a rag.

7.Then drop an appropriate amount of lubricating oil into the bearing.

8-1.Then put the dust cap and C-ring back into the bearings.

8-2.If you find it troublesome to remove the cover for the next cleaning, you can also leave the dust cover on, but remember to install the side without the dust cover facing inward.

Put it in the basin and wipe it with a damp cloth, and you shouldn't be able to get into the washing machine.

This is simple, stuff a stack of thick clean paper towels in it for two or three days, and you can absorb the smell of your feet. And the paper towel can still be reused after absorbing odor, of course, it is not used to wipe the face, it can be used to wipe the oil or something.

Shoes or wipe the surface, put in the water after the wheel and the knife holder will be rusty, as for the tool holder bearing can not be taken down only wipe, the bearing position is regularly oiled, if the tool holder bearing can be disassembled, the tool holder is mainly cleaned and the wheel connection place, the bearing is soaked in oil is the best.

With a roller skating driver, loosen the screws and you can remove them.

Inline roller skates are comfortable and easy to learn, and are loved by the majority of roller skating enthusiasts. I am here to introduce the maintenance of roller skates for your reference, as long as you can maintain your inline skates well, you can save a lot of money, in addition to thorough maintenance of skates, it is also very important for your own safety, so you must do a good job in the maintenance and maintenance of skates, in order to make skating fun. The maintenance of the wheels will gradually wear out with the increase of use time, so the most important thing in the maintenance of the wheel shoes is the inspection of the wheels, it is best to check the wheels once a week to see the degree of wear and tear of the wheels, if the wheels have a certain side of the wear is more serious, you must change the position earlier, otherwise the wheels may break, in addition, you must wipe off the dirt on the bearings with a cloth, check whether there will be strange sounds between the bearing washers and the bearings and the rotating shaft, and rotate each wheel at the same time to see if they can roll normally, Also pay attention to whether the axis of rotation is bent.

Since these parts are often worn out, it's a good idea to have a backup set at all times. The secret of wheel replacement 1Number the wheels first and mark them.

2.When changing wheels, it is recommended that you swap the No. 1 wheel on your left foot with the No. 3 wheel on your right foot, and it is best to rotate (reverse) the inside and outside of the wheel. According to this rule, the No. 2 wheel on the left foot and the No. 4 wheel on the right foot are swapped, then the No. 3 wheel on the left foot and the No. 1 wheel on the right foot are swapped, and finally, the No. 4 wheel on the left foot and the No. 2 wheel on the right foot are swapped.

Special attention is paid to the action of changing wheels only once every half a month to a month. Adjustment of wheel height Some models of wheel shoes, when installing the wheel on the base, need a part called adjustment pad, we can adjust the height of the wheel with various sports needs. Cleaning of bearings If the bearing is contaminated with dust, it can be cleaned with a dry cloth or toothbrush.

If you want it to turn more smoothly, you can use a special maintenance oil. Replacement of bearings Remove the bearings with a three-pronged screwdriver and wipe them with a dry cloth. When putting the bearing back on, do not lock the screws too tightly.

In addition to the helmet, pads such as knee pads and elbow pads are not only easy to absorb sweat, but also easier to get dirt when falling, so they quickly become smelly and dirty, so they must be cleaned regularly every once in a while. Cleaning steps for the inner lining Step 1: Put the liner in the laundry tub and add warm water.

Step 2: Add a detergent that is designed for soaking and does not need to be rinsed. Step 3:

Soak overnight, take it out the next day, and leave it in the shade to dry. (Remember to use lukewarm water, if you soak in cold or hot water, it will cause the liner to break.) Replace the brake pads The brake device on the heel of the shoe will wear out quickly if it is used frequently, and once the wear is severe, it is easy to lose balance when stepping on the brakes, and it may also lead to ineffective brakes, so the brake pads must be replaced immediately after they are smoothed.