Xiao Wang s family purchased a new printer and shared it with a laptop through a desktop computer?

1. Right click on the win icon in the lower left corner of the desktop computer.

2. Select Network Connection in the pop-up menu.

3. Then click Change Adapter Options.

4. Right-click on the Ethernet icon in the new window and select Properties.

5. Click on Internet Protocol version 4, and then click on Properties.

6. Set the IP address as shown in the figure below, click OK. Once you have set up your IP address, you can share your printer.

Printers can be shared in a variety of ways, and network printers can be used for more convenient connections.

Hello! It's not that troublesome! If both computers are under the same router, then the printer can be shared normally, and the IP address does not need to be set separately.

Either one is fine, as long as it doesn't conflict with other network devices such as laptops. Gateway or.

Subnet mask.

The printer is hung on the desktop and then shared out. Press Win+R on the laptop to enter the IP (desktop) at the running place, and right-click to connect the printer that pops up.

Just click below to set it up.

IP address. Mask gateway.

dns hope to give one, thank you!

Xiao Wang's family purchased a new printer.

It can be shared with a laptop computer via a desktop computer.

After the printer is installed on the desktop, the printer is set to share, and the notebook can be installed with a network printer (shortcut: press the windows key + R, bring up the running window, enter this is the desktop IP], the window will have the printer, right-click to connect, and then you can print).

Keep them all on one network by adding a network printer.

1. Connect the two computers through a router or switch.

2. Set up two computer components for LAN and set up sharing.

3. Connect the printer to one of the computers, install the driver, and debug it to print normally4. Add a network printer to another computer, point to the printer of the other computer, and install the driver, and you can share the printer.

Note: The computer on which the printer is installed cannot be turned off, otherwise the other computer will not be able to use the printer.

One: Host.

1.First of all, the driver should be installed, and then right-click on the printer icon to --- share (the name of the share is best to write the printer model) - if a small hand appears on the printer, the sharing is successful.

2.Configure Netsoft Sharing Protocol: To share printers, all computers must have file and sharing protocols installed.

First of all, the NetNeighbor - right-click --- Local Connection - Properties, check in front of Netrob and File Printer Share, and click Install - Double-click on the protocol - Add IPX, SPX protocol point OK (if you can't establish a workgroup, run the Netrox Installation Wizard)1First, open the online neighborhood (click on the home or small office network, click on the next - select the other --- next - the first one - write the name as you like - and go all the way to the end. ）2.

Use to resolve LAN sharing. 3.Enter it in the command.

Find the computer

browser

Then change the startup type to Automatic.

Select Start for Service Status.

At least one machine must be optionally started).

Two: passenger aircraft. 1: First click Add Printer in the printer--- select the screen printer--- select Browse the printer to find the name of the first printer (or select the name of the printer connected to this printer.

The name is written with the name of the first station).

2: Then install the file sharing protocol, add ipx, spx protocol.

1. Both computers are connected to the same router.

2. Right-click on the desktop network --- properties --- change the advanced sharing settings 3. Select Public Network --- select the following options: Enable network discovery--- Enable file and printer sharing--- Enable sharing so that users who can access the network can read and write files in public folders (can be left unselected) - Turn off password protection sharing (other options use the default).

4. Save and confirm.

5. Select the folder or drive letter that needs to be shared, right-click --Properties 6, open the Share tab--- select Share --- pop-up dialog box--- add "guest" - share.

7. Select Advanced Sharing --Select Share this file --OK8. Double-click on another computer to open the network, and the folder or drive letter you just shared will appear.

Note: To prevent accidental errors, turn off the firewalls on both computers.

1. All the computers you want to share are operated in the following steps: right-click on the online neighbor = >> Properties = >> set up your home or small office network, after several next steps, set the computer name casually (each computer is set different), set a team name (each computer must be set to the same), and one step to pay attention to selecting "Enable File and Print Sharing", exit after confirmation, and restart.

2.Just set up the printer on the computer connected to it.

3.If unsuccessful, set or disable the WIN Firewall.

1. First click to open the control panel in the start menu bar.

2. Click System Security, and then click Firewall.

3. Click this to turn on or off the firewall and <>

4. Then select All Closed.

5. In the control panel, select the printer and right-click to select Preferences.

6. Click on this share, and then click OK.

7. On the computer where you want to add a printer, click to open "Devices and Printers" in the start.

8. Then enter the control panel, click Add Device, and select the printer you want to connect.

9. Then you can connect.

1. Find the printer on your desktop computer, select Share, after successful sharing (Note: the sharing group is best the same group as yours) and turn off the firewall. Look at your desktop's IP address, or hostname.

2. There are two ways to add printers on your computer:

Click Start Menu --Run--Enter " Shared Printer Name.

Click on the network neighbor (winxp) or network (win7) to open the workgroup, if you add the share is the same workgroup, you should be able to see your shared printer directly, click add it.

Ask. Now the same working groups can't visit each other.

Set up a local area network: Double-click on "Online Neighbors" - select "Set up a home or small office network" under "Network Tasks" on the left - n....Next is followed by "Enable File Sharing."

to continue to "Next" --Create ing--- create successful--- there are four options, choose the last one --ok

Both computers need to be built, the workgroup should be the same, the default is the mshome test: online neighbor -- view the workgroup -- find another computer -- success.

If you cannot connect to the host after the creation is successful, turn off the firewall of the host.

First, make sure that computer A has a printer installed and is shared. We click on the system"Get started"- Devices and printers: click the "Add Printer" button in the pop-up dialog box: click "Next" in the dialog box that pops up later

Select "Network Printers or Printers Connected to Other Computers": Select "Browse Printers": To this interface we pay attention:

If it is a company user, we can see that there are many workgroups in the box of "shared printer", we need to know the workgroup of computer A connected to the printer, and find the name of the shared printer in its workgroup, and click "Next" If it is a home user, then what we see is the printer shared in our home. At this time, the "Connect to Printer" dialog box will pop up, and we can click "Yes" to install: then the interface will pop up as shown below, asking us if we need to print the test page, and we will click "Next" after selecting it, that is, to complete the installation.

Finally, we open the "Devices & Printers" dialog box on our computer and see the printers we added.

Hello. To share, the computer must be on a local area network and have a fixed IP address.

First, click "Start", "Settings", "Printer & Fax" to enter the printer interface. Right-click the printer you want to share and click "Share" to confirm.

Then click "Start" and "Run" to enter cmd Enter, enter ipconfig in the pop-up window to view the IP address item, record it, and close the window.

Then go to another computer, click "Start" and "Run" to enter the IP address you just recorded (don't forget the first two backslashes), and press Enter. In the pop-up window, you can see the printer you just shared. Right-click on the properties of this printer, click "Connect", and a shared printer will be generated in the computer after success.

PS: It should be noted that some computers have firewalls and some antivirus software, which will block access, so it is best to turn off the firewall or something in the connection.

I don't know what printer yours is, A shift of printers are installed on the desktop, and then the printer is shared, and then the notebook finds the shared printer on the desktop through the network, and then sets the found printer as the default printer, so that as long as the desktop is turned on normally, the notebook can use the printer normally,

First of all, you need to open the sharing of your XP system, that is, to allow guest access, generally the default is on, as long as you use 360 and other optimization software to optimize with one click, and then find the printer in the control panel, after seeing the brother model printer, right-click to select Share the printer, and then enter the control panel printer option on another computer, add a printer, add a network printer, and then it will automatically search, the search may be a little slower, normally you can see your shared printer, After it is selected, the driver will be installed, and it can be printed after installation.

In a local area network, if the printer has a wireless or wired network printer, the printer driver can be installed and used, of course, the following settings must be made, if the machine does not have the network printing function, the printer can be set as a shared printer, and the printer can be used in a shared way.

The computer driver is ready, and the printer for the computer is plugged into that line.

Hello, do it in your desktop computer.

1. Select "Printers & Fax Machines" from the start menu

2. Click on the printer you have installed.

3. Select "Share".

Do the following in your notebook:

1. Select "Printers & Fax Machines" from the start menu

2. Add a network printer.

Set up a home LAN to link two computers through a router and then share a printer.

You start by watching the online tutorial on forming a home area network.

On your laptop, enter the computer name of your XP desktop computer. Login appears, enter the username and password on the XP.

The two computers must be in the same local area network, and the printers must be shared before they can be connected.

How to share printers between desktop computers and laptops.

Refer to the following:1Start by clicking to open the Control Panel in the Start Menu bar.

2.Click on System Security, and then click on Firewall.

3.Click this button to turn the firewall on or off as shown below.

4.Then turn off all the options as shown below.

5.In the Control Panel, select the printer and right-click Preferences.

6.Click Share, and then click OK as shown in the image below.

7.On the computer where you want to add a printer, click "Devices & Printers" to get started.

8.Then go to the Control Panel, click "Add Device", select the printer you want to connect as below.

9.Then it's time to connect, as shown in the image below.

Right-click the printer icon in the desktop start setup printer and fax machine, select the "Share" command, open the printer's properties dialog box, switch to the "Share" tab, select "Share this printer", fill in the name to be shared in the "Share Name" input box, for example, compaqij, and click the "OK" button to complete the sharing settings.

Configure the network protocol.

In order for printer sharing to be smooth, we must install the File and Printer Sharing Protocol on both the host and client computers.

Right-click on the "Network Neighbors" on the desktop, select the "Properties" command, enter the "Network Connections" folder, right-click on the "Local Connection" icon, select the "Properties" command, if you don't find "Microsoft Network File and Printer Sharing" in the "This connection uses the following items" list in the "General" tab, you need to click the "Install" button, select "Services" in the pop-up dialog box, and then click "Add", and select in the "Select Network Services" windowFile & Printer Sharing, and finally click the OK button to finish.

Installation and configuration of the client.

Now that we've done all the work on the host, it's time to configure the clients that need to share printers.

Step 1: Click Start Setup Printers & Faxes, start the Add Printer Wizard, and select the Network Printer option.

Step 2: There are several ways to add a network printer on the Specify Printer page. If you don't know the specific path of the network printer, you can select the "Browse Printers" option to find the printers shared in the same workgroup on the LAN, the computer that has installed the printer, and then select the printer and click the "OK" button; If you already know the network path of the printer, you can use the Common Naming Convention (UNC) format to access the network resource to enter the network path of the shared printer, such as "James Compaqij" (James is the username of the host), and finally click "Next".

Step 3: At this time, the system will ask you to enter the printer name again, after entering, click the "Next" button, and then press the "Finish" button, if the host has set a shared password, here it will ask for the password. Finally, we can see that the icon for the shared printer has appeared in the "Printers and Faxes" folder of the client, and our network printer has been installed.