How to fold stars with plastic tubes How to fold stars with plastic tubes

Tie a knot at one end of the straw and you'll see the pentagon, then you'll find a chubby pentagon along the edges, and then finish by tucking one end into the previous stack. At this time, it's not like a star, the key is that in the end, you pinch it in the middle of each of the five sides of the pentagon, so that a star with a strong sense of three-dimensionality will come out, hehe.

It is to tie a knot in the simplest way, flatten it, and then wrap the remaining straw layer by layer along the shape of the knot, and finally press it in the middle of each side to puff it up into the shape of a star.

I would.

But how am I going to teach you?

Haha, it needs to be hand-in-hand!

Let's find a skillful girl around you.

I've learned, it's not difficult. Good luck learning soon!

The fold of the stars is as follows:Step 1: Fold the hollow plastic tube in half.

Step 2: Fold the plastic tube at a ninety-degree angle along the fold of the fold to form an isosceles right triangle.

Step 3: Fold the other side of the tube towards the side of the triangle, just over the triangle.

Step 4: Fold back half of the square formed.

Step 5: Repeat the action you just did.

Step 6: Once you have made the six triangles, put the first and sixth together. The two tubes cross up and down around the horns of the stars.

Step 7: Hold one of the tubes in place by threading it through the void.

Step 8: Cut off the excess and you're done.

Material: A small straw for one step:

1) The straw is folded backwards;

2) Turn the left tube to the bottom right;

3) Turn the top tube down to the left;

4) Turn the two tubes up together;

5) Wrap the left tube through the right tube and fold it to the bottom right;

6) Wrap the upper tube through the lower tube;

7) the two tubes are turned up together, and the steps (4), (5), (6), and (7) are repeated with the same step (4);

8) Place the first corner close between the two tubes;

9) Wrap the left tube through the first corner;

10) The upper tube is folded to the bottom;

11) Repeat steps (9) and (10) to fold the tube to the end;

12) pass one of the tubes through the star;

13) Prune after tensioning;

14) Done.

The following materials and tools are required to make plastic tube folding stars:

Material: Colored plastic tube.

Scissors. Tools:

Hand drill. Drill bit.

Steel wire. Steps:

1.First of all, prepare the colored plastic tubes, preferably different colored tubes, so that you can make a more beautiful folding star.

2.Use scissors to cut the plastic tube into small pieces about 20 cm long, and you can determine the length according to your preference.

3.Use a hand drill and a chia da drill to drill a small hole at each end of each plastic pipe, and the size of the hole should be slightly smaller than the steel wire.

4.Insert the wire into one of the small holes and lift it straight until it sticks out from the hole at the other end.

5.Bending the plastic tube along the wire into a triangular shape with an angle of 60 degrees is the first step in folding out a triangular star.

6.It is then bent again along the wire so that the plastic pipe and the wire form a regular triangle.

7.Then, repeat steps 5 and 6 to fold out 5 triangle-like shapes and bend them along the wire.

8.Cut the wire with scissors to leave some space at the end of the plastic tube, and then fold the end of the remaining wire so that there is a small loop at the end of the wire.

9.Finally, thread all five triangular plastic tubes through the wire loop, placing the ring on the small hole at the other end.

10.By adjusting the angle and pulling, the pentagram becomes flat and hung as an ornament.

This is the step of making a plastic tube to fold stars, I hope this tutorial will be helpful to you, and I hope you can make a Zen He Liang folded stars.