What is the reason why Zede kitchen sewage lift pump does not stop

Updated on society 2024-04-18
6 answers
  1. Anonymous users2024-02-07

    The drainage of the basement is solved by using a sewage lifting pump, so that the sewage in the basement can be discharged from the low to the main sewage pipe at the high place, so that the anti-gravity drainage can be achieved, so that the water can flow from low to high, and it is a cleaner and easier drainage method.

    Can we solve the drainage of the kitchen and bathroom with one machine?

    In general, if the distance between the kitchen and the bathroom is not very far, you can use a machine to solve the drainage problem of the entire basement, such as 1500 series, 60 liters of volume can cope with the large flow of drainage, the machine's back-cleaning system can cope with the kitchen oil, eliminating the need for regular manual cleaning, using tap water to automatically clean the inner wall of the water tank, more concise, and 1500's 50mm large overflow diameter can also cope with the drainage of the basement bathroom, Even if the debris is too large, you can easily deal with it, and you don't have to worry about the occurrence of the problem of excessive debris blocking the pipeline, plus the 75mm large channel anti-clogging air pressure induction sleeve to prevent the oil from blocking the trachea and affecting the control, so that the drainage in the basement is more stable, and there is no need to worry about the problem of control failure.

    But if the distance between the kitchen and the bathroom is too far, it is not suitable to use a sewage lift pump to solve, because too long distance will cause the sewage to stagnate in the horizontal pipeline, although the slope will be set, but there is also this risk, especially the sewage in the kitchen, too much oil accumulation in the pipeline, will be easy to have a blockage problem, this situation is the kitchen and bathroom each with a sewage pump to solve the drainage problem is better.

  2. Anonymous users2024-02-06

    Do you add a grease separator in front of the sewage lifter in your kitchen, if you don't add it, the grease of the kitchen wastewater will condense in the water tank, which will affect the water level control of the sewage lift pump, and there will be no downtime!

  3. Anonymous users2024-02-05

    Stop draining. Zede sewage lifter alarm is overload alarm and overheating alarm, and the over-touch response stove load alarm exceeds the maximum water level, and the drainage should be reduced or stopped. The overheating alarm means that the equipment has been running for too long and the drainage should be stopped.

    German Zede water pump system**** In 1976, the external sewage lifter was invented in Frankfurt, Germany.

  4. Anonymous users2024-02-04

    The principle is to monitor and judge the working state and operation of the pump in the early mode, and trigger the alarm signal when the pump is abnormal. The details are as follows:

    1. Operation status monitoring: By monitoring the current, voltage, power and other parameters of the pump, you can judge whether the pump is operating normally. When the current or power of the pump exceeds the set threshold, it may indicate that the pump is faulty or blocked, triggering an alarm.

    2. Liquid level monitoring: Zede sewage lifting pumps are usually equipped with liquid level sensors to monitor the liquid level in the pumping station or well. When the liquid level exceeds the set high water level or falls below the set low water level, it may indicate that there is an abnormal situation in the pumping station or well, triggering an alarm.

    3. Temperature monitoring: The motor of the pump will generate heat during the working process, and it can be judged whether the motor is overheated by monitoring the temperature of the pump. When the temperature of the pump exceeds the set threshold, it may indicate that the pump is malfunctioning or not operating properly, triggering an alarm.

  5. Anonymous users2024-02-03

    Dear, hello, I am glad to answer for you, the reason why Zede lifting pump does not start Answer: Reason: The packing is too tight or the impeller and the pump body are stuck by debris and blocked; The pump shaft, Tongque bearing, and leakage ring are rusted; The pump shaft is heavily bent.

    Exclusion method: relax the filler, dredge the diversion tank: disassemble the pump body to clear the track wheel slip to remove debris or rust; Correct the bent shaft or replace it with a new pump shaft.

    The motor does not start, does not rotate and drains, accompanied by a humming sound, and the treatment method is as follows: If the phase is broken, repair the line; Bearing shaft, repair or replacement of posture; There are foreign bodies in the impeller and the pump body are stuck, and the foreign bodies are removed; If the voltage is low, adjust the voltage.

  6. Anonymous users2024-02-02

    1.Check the power supply: Make sure the power cord of the pump is properly connected and check that the power outlet is powered.

    Check that the power switch is turned on. If using an outlet switch, make sure it is turned on. 2.

    Check the wire connections: Check that the wire connectors are secure and not loose. If there are loose or damaged wire connections, reconnect or replace the wires.

    3.Check the fuse: Check if the fuse of the pump is working properly.

    If it is a fuse, check that the fuse is open and replace the fuse if necessary. 4.Clean the pump pool or pump body:

    Sometimes, blockages or dirt inside the pump can cause the pump to not work properly. Please disconnect the power supply first, and perform the necessary cleaning and removal. 5.

    Check the drain of the pump: Check if the drain is blocked or blocked. If you notice a blockage, clean the pipes to make sure the water is flowing smoothly.

    6.Check the float switch (if applicable): For sump pumps with float switches, make sure the float is not stuck and can move freely.

    Clean or replace any damaged float switches.

    It used to be normal, but now it smells bad and doesn't work.

    Check the power supply: Make sure the power cord of the pump is properly connected and check that the power outlet is powered. Check that the power switch is turned on.

    If using an outlet switch, make sure it is turned on. 2.Check the wire connections:

    Check that the wire connectors are secure and not loose. If there are loose or damaged wire connections, reconnect or replace the wires. 3.

    Check the fuse: Check if the fuse of the pump is working properly. If it is a fuse, check that the fuse is open and replace the fuse if necessary.

    4.Clean the pump pool or pump body: Sometimes, blockages or dirt inside the pump can cause the pump to not work properly.

    Please disconnect the power supply first, and perform the necessary cleaning and removal. 5.Check the pump's brother drain pipes:

    Check that the drain is not clogged or blocked. If the hair is blocked, clean the pipes to ensure that the water is flowing smoothly. 6.

    Check the float switch (if applicable): For sump pumps with float switches, make sure the float is not stuck and can move freely. Clean or replace any damaged float switches.

    Kiss to your expansion, mobile phone battery maintenance precautions: 1, but re-ignition guess charging, overcharging will accelerate the battery consumption. 2. Use the original charging head, the non-original charging head is very depleting of the battery.

    Happy leak type] <>

Related questions
8 answers2024-04-18

It mainly depends on how much you use in the bathroom, if it is a household, you can consider the Zede kompaktboy single pump series. >>>More

18 answers2024-04-18

Household or commercial, head, flow and discharge medium, a combination of choice. For example, you can choose a single pump for household use, and you can choose a double pump for commercial use.

12 answers2024-04-18

The installation of sewage lifting pumps, small household equipment, according to the installation pipeline interface and location reserved in the early stage of decoration. >>>More

14 answers2024-04-18

Friends who have a basement in the villa should not be very unfamiliar with the word sewage lifting pump, because if we have a water point in the basement, we will use the sewage lifting pump to solve the problem that the basement is not under water. >>>More

9 answers2024-04-18

After we have determined the model selected for the sewage lifting pump at home, the follow-up installation process is generally handed over to the technical installer, but we should still know some tips about the installation, so that in the follow-up use process to determine it is more handy, and also know how to better develop good habits. >>>More