Who knows what should I do if I can t log in to the management interface after setting up the TP Lin

Sometimes we can't log in to the management interface of the TP Link702 wireless router after setting it up, so we can't perform more advanced operations on the TP Link702 wireless router settings. The occurrence of this phenomenon requires us to investigate the following causes step by step.

1.When connecting a wireless signal to a wireless terminal, make sure that the correct wireless signal is connected. Check whether the name of the wireless network that the computer has connected to is the default SSID of the router.

2.Make sure that the Internet terminal obtains the IP address through DHCP and obtains the correct IP address (the gateway IP address is the IP address of the front-end router).

3.Try to disconnect the line of the mini router (the wired interface of the router is not connected to any devices), power off and restart the router, and try to log in to the management interface again using the management address of the router.

4.If the above operations still do not solve the problem, we recommend that you reset the router.

5.After resetting, I still can't log in to the interface, so I need to check my browser settings.

6.If you still cannot log in to the interface, we recommend that you change the wireless terminal for testing.

It is recommended that children who cannot log in to the management interface after the TP Link702 wireless router is set up try the above operations. Router reset can solve many problems of routers, which is not only for 702 for Pulian, but also for Tengda, Pole Routing, Leike and so on.

You are not changing the password of the multi-wireless router, you can initialize the router under it.

Have you changed the address of the router?

1. This router has only 1 LAN WAN multiplexing interface, which is a WAN port when working in routing mode, and cannot be set with a network cable, so it should be connected and set up wirelessly.

2. The router is turned off by default DHCP at the factory, and the computer IP used for setting before enabling DHCP should be set to a static IP (.

3. The default IP address of the router is.

What should I do if the TP-Link wireless router cannot log in to the management interface?

Hello dear, happy to answer for you,Confirm that the method and input on the login management screen are correct. Open your browser and type "

cannot be entered as". And press enter. If it still doesn't open, go to the next step.

2.Check and confirm that the device is connected correctly. Connect the computer network cable to one of the router lan1 4, power on the router, check and confirm that the status of each indicator is normal.

Check and confirm that the computer network parameters are set correctly. The computer is set to automatically obtain the IP address by default. Hope this helps<>

Method steps.

Check 1: Check whether the line connection is correct.

Check 2: Make sure that the IP address of the computer is obtained automatically.

Check 3: Confirm the login method.

There are two types of routers: domain name login and management IP login, which are as follows:

1. Domain name login.

On the tin mark at the bottom of the router is written "Management Page:, as shown in the figure below:

The page pops up the login dialog:

2. Log in with your IP address.

Note: If the environment is a rental house, community broadband, office LAN, or hotel environment, the router will automatically detect the front-end network and adjust the network segment to avoid IP network segment conflicts. Therefore, when logging in to the management interface with an IP address, be sure to confirm the IPv4 default gateway address that the computer actually obtains.

Troubleshooting 4: Check your browser settings.

Please check your browser settings as follows:

Disable dial-up connection: Open IE browser, click Tools >>Internet Options, select Connections >> never make dial-up connections.

Disable Network**: Click Tools >> Internet Options, select Connect >> LAN settings, make sure none of the three options are checked, and click OK to go back to the previous Internet Options dialog box and click OK. As shown in the figure below:

Turn off offline status: Offline status will affect normal browsing of web pages, click the browser File >> work offline, and make sure that it is checked before offline work.

Once the setup is complete, try to log in to the router management interface.

Check 5: Change your browser or computer.

Change your browser (Firefox, Google Chrome, or another browser) or try to log in to the admin interface on a different computer.

Check the six-reset router.

When the router is powered on, use a paper clip or other pointed object to press and hold the reset button on the back panel of the router for 5-8 seconds, and the indicator light on the front panel flashes three times to become solid on, indicating that the router has been reset successfully. Reference:

It is recommended that you check the connected network cable, and if not, restore the router factory settings.

1. When the router is powered on, hold the reset hole or button for about 10 seconds, and wait for the indicator lights on the router to turn off and turn on again, and the router will be restored to factory mode successfully.

2. The computer connects the router through the network cable, and uses the default IP address of the router and the default login username and password to log in to enter the router background, and the default IP and user name and password can be queried through the parameter values on the back of the router.

Note: After the router is factory reset, you need to reset the Internet parameters to have a normal Internet experience.

Log in to take a look, and if it doesn't work, it is recommended to reset the router:

1.Change the local connection to automatically get an IP address.

2.When the wireless router is plugged in, do not connect the home network cable first, reset the wireless router (restore the factory), connect the computer to any "LAN" port of the wireless router, enter the setting page, and set it according to the PPPoE (ADSL virtual dialing) method. Then set the SSID, encryption method, and password.

Save, restart. After setting up, connect the home network cable to the "WAN" port of the wireless router.

First confirm that the network cable is connected correctly, plug the network cable of the computer into any port to connect the cat in the WAN port, and then enter **Enter in the browser, enter the username and password are all admin!!

1. You can restore the router to factory settings first, there is a small hole in the back of the router, generally RST or RESET, find a small and sharp thing such as a toothpick or pen tip, and poke this small hole for more than 5 seconds when the router is powered on to restore the router's factory settings; 2、.Re-set the relevant network parameters of the router: The router is a device that forms a LAN to achieve network sharing, and the general connection and setting methods are as follows:

Connect the network cable out of the broadband cat to the WAN port of the router, each computer is connected to the LAN port of the router, the IP address of the computer network card is set to be automatically obtained, enter it in the address bar of the computer browser, specifically to view the network parameters obtained by your computer network card, and log in through the IP address of the gateway) Log in to the router, the general user name and password are admin, select the WAN port setting, Set your broadband account and password to the PPPoE mode (if it is a fixed IP, you should choose the static IP mode), save and restart.

Check your local connection with your computer to see what the default gateway is.

Enter the gateway on the web page to enter the router, and the general account password is admin

If it doesn't work, try it with guest.

When you restore factory parameters, 703N is the default AP mode, in this case the DHCP function is turned off and no IP is assigned. And your computer automatically obtains the IP, if there is no other router on the front end responsible for assigning the IP, then it will definitely cause you to be unable to log in.

Set a static IP address on your computer, such as a mask, and then connect to 703n and log in to the management page.

- If you are using a wireless connection to manage the 703, then set a static IP for the wireless card of the laptop. If you are connected with a network cable, set the static IP address of the wired NIC in the local connection. Once connected, you run cmd and ping to see if it works.

If it's connected, but you still can't get in, clean up your browser's cache and try again. The 703N can be temporarily denied a broadband network cable.

The following steps can be used to resolve the tp-link wireless router that cannot be logged in

1. The default address of the tp-link route is to restore the factory settings if it does not work.

2. Turn on the router and press and hold the reset button on the router until all the lights flash at the same time, then the router will restore the default login address.

3. If you still can't log in, then check whether the network cable connecting the router and the computer is loose, or use a wireless connection to set it.

4. If it doesn't work, then it is caused by the failure of the router, and the router can only be repaired or replaced.

Check your local connection with your computer.

See what the default gateway is.

Enter the gateway on the web page.

It's into the router.

A general account password.

It's all admin

If it doesn't work, try it with guest.

It may be that the IP of the TP wireless router has been modified, try or, it is better to check the IP of the fiber modem, because it can't be the same, the wireless router must have been modified, I really don't know, the TP wireless router returns to the factory settings, and resets the wireless router.

1. Check the IP first, method: win+r--- enter: cmd--- enter in the black and white interface: ipconfig, press enter.

Log in to the router management interface

2. The router login interface pops up and enters the default login username of the router: admin and password: admin (if it is incorrect, look at the back of the router).

Note: The known password and the default password of the router are incorrect, and the administrator password can be retrieved by resetting the factory settings of the router; When the router is powered on, use a pointed object such as a paper clip to press and hold the reset button (button) on the back panel of the router for 5-8 seconds, and the indicator light on the front panel flashes three times to turn solid to indicate that the router has been reset successfully. Try logging in to the admin interface again.

Change the router password:

1. First of all, we log in to the wireless router control interface browser input;

2. There are wireless settings in the control interface - > wireless security settings;

3. We change the PSK password in wpa-psk WPA2-PSK on the right.

1. First of all, you can use a laptop or desktop computer to connect to this line to see if you can get IP and surf the Internet normally. If you're not sure, don't worry, as long as your laptop turns off the "Wi-Fi" and you connect to the Internet via wire, or your desktop goes straight to the Internet, everything is fine.

2. In case the computer cannot be connected to the network on this line, it means that the "DHCP" setting of the wireless router is not normal. You can log in to your router and set it up. Please refer to the manual of your wireless router for detailed steps. Key points:

a. "Enable DHCP".

b. Fill in the correct "gateway" or "network segment" (most of them, some of them).

c. Fill in the correct DNS server address, which can be viewed in the "Status" section of the router.

d. Some routers have "Enable DNS Relay", please enable it.

That's when you press the qss reset press on the back.

I don't really understand mine is typing in the browser.