Can PA11 be mixed with PE to make pipes?

I think it's okay to mix blowing. However, to achieve a high level of transparency, it is necessary to have a precise grasp of the addition ratio. PE polyethylene is an addition reaction and polymerization reaction of ethylene (CH2=CH2).

It is best not to put these two together to make some coffins, because this kind of production is likely to lead to the unsturdy pipe.

PA11 can be mixed with PE to make pipes, but its performance may not meet the requirements you need.

These two are separated from each other, so they can't be managed together.

I just inquired for you. These two can be mixed together. No problem at all.

If the two of them are mixed together, they can't be in charge, because each girl is different.

This is also possible, because their two materials are basically very common on the market, and this one is also very safe and non-toxic.

In this case, it is not possible because they have some conflicts in some cases, so it is not possible in this regard, and it is easy to have some failures.

That thing can't be mixed together, because the two machines are different, the models are different, no.

It is better not to mix the two products you are asking about, and it is better to use them separately in the context of school questions.

Can they be put together to make tubes? They can also be put together to make tubes, and if they can't be connected, they can be soldered.

PPR and PE pipes should not be hot-melt connected, but should be directly connected with internal and external teeth. The wall thickness of PE pipe and PP-R pipe is different, and the welding strength of the two materials cannot be reached.

PE should be able to be dried with PE, and this should be a little stronger, so it should be able to do better some time.

The unit can be used together with leather powder to make a tube. If you do it together, you can make it together according to his configuration, and you can make it according to various configurations.

Can P 211 be managed with an ETF? No, the period of Feng Yong Lesson 17 is managed, and if you mix and wait for a while, then don't give him the management management.

This is definitely okay because they are the same on this model, so it must be very good to say this, thank you.

If it's two forms of stuff, you can't be an official.

Hello, this situation is generally not supported, so you must be patient, otherwise it will not work normally.

If it's mixed together, it shouldn't be particularly good.

Under normal circumstances, then he should not be able to do it directly, so this still needs to be done by adding some other things. In general,

OK! However, the amount of addition should be moderate, and we sometimes use PP and PE to make modified materials.

Polyethylene (PE) is a thermoplastic resin prepared by polymerization of ethylene. In industry, it also includes copolymers of ethylene with a small amount of -olefins. Polyethylene is odorless, non-toxic, feels like wax, has excellent low temperature resistance (the lowest use temperature can reach -100 -70 °C), good chemical stability, and can resist the erosion of most acids and bases (not resistant to acids with oxidizing properties).

It is insoluble in general solvents at room temperature, has low water absorption and excellent electrical insulation.

PE can only account for a small amount, about 10%, and a compatibilizer must be added. Pull tabs are no problem.

PE pipes can only be produced with PE materials, and if you need to enhance and toughen, you can add other things to modify them.

The current pipes are basically made of recycled materials, but PE pipes must not be added with PP

The full name of PPR that will definitely have problems is non-return copolymer polypropylene, PE seems to be called friend side answer non-return copolymer polyethylene barrier, the properties of the two materials are completely different, and they cannot be well bonded together. If PE or PPR is to be used, a wire fitting is required for conversion.

I've tried to use PE fittings to connect the source grip PPR water pipes together.

I've also tried to connect PPR pipes with Pert fittings. It can also be linked together.

But I still agree with the upstairs, after all, the material is not the same as the crack is now possible, who knows what will happen in the future!

Looking at the ratio, if there is less PPR, the problem is not big, and it is not cost-effective to separate.

PU thinner as PE thinner can not achieve the dissolving effect on the paint, which will cause the orange peel on the paint surface, and the use of PE thinner as PU thinner will cause the phenomenon of biting the bottom.

PP and PE can be compatible, there is no problem with mixing together for granulation, the performance is between the two, of course, if it can be separated, it is better to separate and granulate separately.

There are a lot of mulch films, woven bags, etc.

Yes, that's fine.