The results of the test with the memory testing software are analyzed by the experts

Your memory module should be a memory module that is often referred to as a bad fun in the enterprise, an IC problem.

Let's buy a new one.

How to confirm the defect:

1. Appearance confirmation (mainly to confirm whether the resistance is offset or dropped; Whether the gold finger has a short circuit or an open circuit).

3. If you are at home, use the dedicated test software (there are many on the Internet).

Friend,,, it's not too difficult to be like you, first determine whether the memory is broken, to see if the small resistor on the memory is broken, but also whether it is broken, your computer can not be used, other computers can be used, this situation occurs, it means that your memory is likely to be repaired, to see if there are solder joints on the memory IC in different places, if there is a repaired memory,,, it is best to go to the regular store to change an original memory,, Some motherboards are not very compatible with some of the original memory,,Generally speaking, as long as it is the original**Most of them are no problem,,It is best to restore the biso to the default before reinstalling the system before installing the system,,There is also a situation,,Your computer has a strong virus,,You need to use a disc to start the antivirus and then install the system,,I opened a computer store at home,

Generally, the voltage can be measured with the software AIDA64.

The hardware can detect the card with the memory and can also know the voltage.

1. The core power supply of DDR3 can be measured on the PIN of the value card or the memory module.

2. The load power supply of DDR3 is half of the VTT DDR of the main power supply (, which can be measured on the pin.

3. The SPD power supply VCC SPD of DDR3 can be measured on 236pin.

4. The reference voltage VREF of DDR3 is and can be measured on the PIN.

5. There are a total of 4 clocks of DDR3, which can measure the voltage or waveform on the pin.

6. The reset voltage of DDR3 is 168pin, which can be measured.

7. The voltage that can be measured on the PIN of the system management bus SDA and SCL of DDR3.

Use a black pen to connect the metal case on the motherboard (which case is plugged into the earphone), and then use a red pen to measure the metal shrapnel of the memory slot. Each shrapnel has a name abbreviated in English, and if you don't know it, you can test it one by one. There is no and there is none. Good luck!

The load of the car has increased, so it has caused the car to idle and shake, so I specially consulted an experienced car repair master, and the car repair master said that if the car idles and shakes as soon as the air conditioner is turned on, it may be because these places should be checked.

I would like to make the following suggestions:

1.Manual testing.

In fact, many such as making slippery nuts really have problems with memory. It won't even start. This is in a bad situation.

2.The software test is good or bad (I recommend the following software):

memtest86 is a free memory testing software, the test accuracy is relatively high, and the hidden problems of memory can also be checked! You can get there.

memtest86 is a Linux core-based test program, so its installation and use are a bit different from other memory testing software. After unzipping the memtest86 program**, we can see 4 files that are used to install the memtest86 program to a floppy disk. Double-click to run this program in the pop-up window "Enter Target Diskette Drive:."

After entering the drive letter of your floppy drive, such as A, then press Enter. Insert a formatted floppy disk, click enter to open the pure file to start the installation, so that memtest86 will be installed on the floppy disk. As we said earlier, memtest86 is based on the Linux core, so we can't see the contents of the floppy disk in Windows Explorer (don't mistake it for not having content on the floppy disk).

If you don't have a floppy drive, the homepage of MEMtest86 has the ISO file of the software, which can be burned directly to the CD-ROM dust disk, and tested after booting with the CD-ROM drive.

If you are using a sedan chair to roll down win7,Enter the word memory in the start menu,Select the memory diagnosis option that pops up,Then it's left to the computer to complete it yourself。

Desktop My Computer Left-click the mouse My Computer and click on the properties to view the memory size, specifications and brand!